Ubuntu Servers :: Bond1: ERROR While Getting Interface Flags: No Such Device
Oct 14, 2010
On Ubuntu Server 10.10 the second bond device won't come up. Someone please advise the correct configuration. Error message when I run /etc/init.d/networking restart:
Code:
SIOCSIFADDR: No such device
bond1: ERROR while getting interface flags: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
bond1: ERROR while getting interface flags: No such device
bond1: ERROR while getting interface flags: No such device
Failed to bring up bond1.
[code]...
View 5 Replies
ADVERTISEMENT
Mar 26, 2011
i am trying to connect my AWUS036H to my Compaq CQ60 laptop running Ubuntu 10.10. when i check ifconfig, one minute my wlan1 is there, next minute its not, if i try to do a sudo ifconfig wlan1 up i get, wlan1: ERROR while getting interface flags: No such device and when i try it again it accepts the command no probs, i suspect this is because the device is in and out every few seconds. when i checked rfkill, i found a hard block which i resolved with unblock all, i have checked the unit under windows and it works just fine so i suspect it is a problem with my ubuntu
View 2 Replies
View Related
Apr 9, 2010
I am having an odd problem with a program I'm trying to run which is supposed to connect to a network. The messages printed when I start up the program are:
SIOCSIFNETMASK: No such device
192.168.11.50: ERROR while getting interface flags: No such device
SIOCADDRT: File exists
One reason this is particularly odd is that the network itself appears to be working fine, otherwise. I can connect to the internet on my computer and everything, but the program is not able to connect to it, for whatever reason. I've tried tinkering with the settings but nothing worked.
View 3 Replies
View Related
Mar 29, 2011
I wanted to stop hi jacking the work around thread. I'm running Kubuntu 64 bit I started by following this walk through[URL].. everything is fine until i get to Step 5 this line :
sudo ifconfig wlan0 down (on some hardware it is ra0)I receive this output: wlan0: ERROR while getting interface flags: No such device I started browsing other threads to see what else could be happening. I ran this line : sudo lshw -C network
with an output of:
*-network:0 UNCLAIMED
description: Network controller
product: RaLink
vendor: RaLink
physical id: 0
bus info: pci@0000:06:00.0
version: 00
width: 32 bits
[Code]...
View 9 Replies
View Related
Jun 28, 2011
While using wifi slax every gos ok until i get wlan0 error while getting interface flags no such device how can i fix this.
View 1 Replies
View Related
Jun 14, 2010
yesterday without reason my eth0 dissappeared. I read through various threads, tried couple of things, and now its s back as eth3. If I bring up the network on the console it says [OK], but I cant ping my router or access any website.
BTW: During the proccess I removed network-manager-kde, which I regret now (cause I cant install it again w/o network). Even so my network was configured manually, it would be good to have it now for testing connections. The machine also got no CDROM-drive, I installed via USB.
EDIT: I booted up again, and now eth3 is gone again I get the former error message when I restart the network: "eth3: ERROR while getting interface flags: No such device"Same with all other ethX. As far as I can see w/ my basic knowledge, the realtek adapter is present and working. ifconfig only shows me "lo" nothing else.
View 9 Replies
View Related
Jun 15, 2010
I am reporting various network statistics in a c++ program by reading the values out of /proc. However, I am having trouble determining the link status. In particular, I am wondering:
1. How are the standard interface flags (IFF_UP, IFF_RUNNING) as referenced in if.h accessed from user land? The ifconfig man page lists its files as
/proc/net/socket (doesn't exist in suse), /proc/net/dev, and /proc/net/if_inet6. None of these seem to contain these flags.
2. ip link show reports a "NO-CARRIER" flag. How does this correlate with the "UP" and/or "RUNNING" flags as reported by ifconfig, and how is it accessed from user space?
View 1 Replies
View Related
Nov 15, 2009
I have 2 network cards eth0 and eth1, for eth0 i set a manual MACADDR in network scripts. Ok so every time i boot, if the cable is plugged in, my eth0 fails to mount or i don't know.. i get this after bood when i type ifoncifg eth0 (eth0: error fetching interface information:Device not found). So i have to unplug the cable when i boot, then plug it in and do a service network restart.
View 5 Replies
View Related
Jul 12, 2010
I am getting the same errors everytime I boot the server up:
Error: no such device {SOME-UUID}
Error: no suck disk
After that the system boots normally, but Im afraid ignoring this error can make my system crash in the future. I figured it was a grub error and I tried the update-grub2 command, it does detect all installed kernels no problem, but after I reboot I get the same error message.
View 9 Replies
View Related
May 5, 2010
My network name is eth2 it was changed by some reason and now i got these errors... i installed, reinstalled, re re installed, tried to run the asistant but no luck :/
Code:
* Stopping the Firestarter firewall...
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
[code]....
View 1 Replies
View Related
Feb 17, 2011
I'm trying to cross compile something and it requires a recent version of Boost. I'm using squeeze and gnome and my updates are all up to date. I could not get through the 'configure' stage with Boost dev packages from the debian repository, so I went to the Boost web site. I thought the package requires boost 1.44 or later, so I downloaded 1.45.0 from the site and proceeded to build and install it. I think I installed it right, using /usr/local/ as the prefix. Back at my main project, I try to configure my build and I get some of the following text and then the configure stops.
Code:
checking for Boost's header version... 1_45
checking for the toolset name used by Boost for arm-none-linux-gnueabi-g++... configure: WARNING: could not figure out which toolset name to use for arm-none-linux-gnueabi-g++
checking boost/date_time/posix_time/posix_time.hpp usability... yes
[code]....
I cannot get past the 'date_time' thing. Does anyone know what is meant by 'flags to link with Boost date_time' ?
View 2 Replies
View Related
Dec 26, 2010
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies
View Related
Aug 4, 2010
The system is an old AMD Duron 650MHz that was dug out of the garbage, trying to set it up as a light duty server. I installed ubuntu 10.04 with no errors or troubles during the install, however whenever the system is booted it sits at a cursor for about a minute then goes into busybox giving the error "Gave up waiting on root device." and says that the hard drive does not excist. If I sit at busybox for about another minute and type exit it then boots ubuntu 10.04 with no errors or issues.
View 7 Replies
View Related
Apr 13, 2011
I'm currently setting up a dell server with hardware raid 1 on sas 6r. i got 4 sas installed on the server and configured to raid 1 as stated below,
array 1:
slot 0 & 1
array 2:
slot 2 & 3
during the installation, the installer detect the array 2 as sda and array 1 as sdb.. so i proceed with installation on array 2. after completed the installation, the first reboot lead me to a 'grub-rescue" prompt. by following the guide at url Mode, i've noticed that the boot folder has changed to (hd1,1), which i believe it has changed to sdb1. default root device shows that prefix=(hd0,1)/grub.
View 3 Replies
View Related
Sep 6, 2011
I have a FireWire camera LifeSize connected to my PC in the FireWire interface. My PC has miniPCI slot and with external converter its having a FireWire interface. Now its Ubuntu who is not showing me anything at all when i try:
$ uname -a
Linux desktop 2.6.38-11-generic-pae #48-Ubuntu SMP Fri Jul 29 20:51:21 UTC 2011 i686 i686 i386 GNU/Linux
[code]....
View 1 Replies
View Related
Oct 17, 2010
I tried removing it and installing again but I still get the same code in the terminal:
[Code]....
View 3 Replies
View Related
Sep 17, 2009
Since May 12,2009. Our system lifekeeper has the error log "lifekeeper error: DEVICE FAILURE on SCSI device '/dev/add'", but it ran normally. Until last week, it failover to the standby server. The disk still running, the error still come out.
View 3 Replies
View Related
Feb 3, 2011
I have problems with my USB driver. After adding my device (MSP430 USB-DEBUG-INTERFACE) it doesn't work.
[ 60.476039] usb 2-2.1: new full speed USB device using uhci_hcd and address 8
[ 60.693959] ti_usb_3410_5052 2-2.1:1.0: TI USB 3410 1 port adapter converter detected
[ 60.693981] ti_usb_3410_5052: probe of 2-2.1:1.0 failed with error -5
I try to do: modprobe ti_usb_3410_5052.No changes.It's Linux
Linux ubuntu 2.6.35-25-generic #44-Ubuntu SMP Fri Jan 21 17:40:44 UTC 2011 x86_64 GNU/Linux
View 1 Replies
View Related
Oct 14, 2010
OpenSUSE 11.3, openssl was just updated with YAST (to see if there is any fix available but not)
# openssl version
OpenSSL 1.0.0 29 Mar 2010
# openssl -genrsa -des3 -out ca.key 4096
[code]....
View 2 Replies
View Related
Jul 15, 2010
I am having trouble setting up my second network interface on Ubuntu Server 10.04. When setting up the machine it did detect both cards but I only picked one to configure, and now I want to setup the second.
I went into /etc/interfaces and basically copied the settings for eth0 but changed the IP and the name to eth1. I then restarted.
Quite honestly it might be working! But when I run ifconfig -a I see no packets I see
Quote:
eth1 Link encap:Ethernet HWaddr 00:0e:0c:59:af:c4
inet addr:192.168.4.21 Bcast:192.168.4.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[Code].....
isn't that what "UP BROADCAST...." line means?
So perhaps my question is how do I test my 2nd interface? I tried using the 2nd IP with Putty (which is how I usually work on the machine) and couldn't connect.
View 7 Replies
View Related
Aug 20, 2010
I have a server with two active network interfaces. On one, I need ssh open for all users (it's running LTSP, and as I learned the hard way today, blocking ssh kills LDM access).
On the other interface (which connects to the rest of the network), I only want to allow a few administrative users to connnect.
Is there a way to do this cleanly using sshd_config or PAM? I don't want to do something hacky like running dropbear.
View 3 Replies
View Related
Apr 10, 2011
I'm currently running Ubuntu Maverick - 2.6.32-30-generic. I recently bought a Garmin eTrex Vista H, which connects via usb (from my reading, it looks like older versions connected over serial). Well, like so many before me, I can't seem to write to or read from the device via gpsbabel.Originally tried to read anything from the device (I have one waypoint in there) via:
Code:
gpsbabel -i garmin -f usb:
It returned "Found no Garmin USB devices." I then tried turning on the eTrex. Doing the same while locating satellites just does nothing - I have to escape from the command in terminal. Trying again produces the error:
Quote:
Claim interfaced failed: could not claim interface 0: Device or resource busy
After doing some research, I unblacklisted and then reblacklisted garmin_gps. I also went into
Code:
/etc/udev/rules.d/51-garmin.rules
to verify that the contents were:
Quote:
SYSFS{idVendor}=="091e", SYSFS{idProduct}=="0003", MODE="666"
as directed in this . Everything seemed to be correct.I then followed some other advice found here and created the policy under /etc/hal/... Still no luck!
View 5 Replies
View Related
Feb 28, 2011
I have an old PC that I turned into a server. I have Ubuntu 10.04 running on it. I am looking for some media server software that can stream .mp3s to multiple computers over a LAN. But, I would like a software that can stream through a web interface. I would like my family to be able to open a web browser and go to the server and play files by clicking on them.
View 5 Replies
View Related
May 2, 2011
Is there any web interface that I can install to remotely reboot ubuntu? It would only be accessible via a VPN or on the LAN so not too much worry over security.
View 3 Replies
View Related
May 9, 2011
Alright, here's the problem: I have a server going that was running 10.10, then upgraded to 11.04 with no problems, but when I reinstalled 9.04 (so i could muck around with GNUPanel), the install couldn't find the ethernet on the motherboard (which I had no problems with on 10.10 or 11.04). I'm a bit of a newb, but it seems to me that something is very wrong here because I can't get online. All of the other computers in my house are unaffected, so I think I can narrow it down to the device not being recognized, but beyond that, I'm lost.
View 3 Replies
View Related
Mar 17, 2011
I just compiled my first own kernel (I'm using Arch Linux), following the tutorial on the german site. Now I tried to boot it, I ended up failing with this message: Code: Waiting 10 seconds for device /dev/sda1 ... Root device '/dev/sda1' doesn't exist, Attempting to create it. ERROR: Unable to determine major/minor number of root device '/dev/sda1' Here is the important part of my menu.lst:
[Code]....
I simply copy&pasted the Arch-entry, i.e. I also had the disk by uuid there. The failure message was the same, just the root device name was the different name Also, at first I did not have the initrd line in my menu.lst (as written in my tutorial that I may not need it). In this case I had this error message:
[Code]....
View 10 Replies
View Related
Jun 16, 2010
I want to set up a home computer as server. I've installed Ubuntu Server Edition 10.04, and can access it through SSH. However, I would like to have a browser based interface for managing things, such as installing a phpBB forum and stuff like that. Also, I want my friends to be able to share files on my home server as well. I know I can do it by using FTP, but I would rather not have them to install a FTP program.
View 9 Replies
View Related
Jan 5, 2011
I have installed ubuntu server 10.04 sucessfully. But I'm new to ubuntu so I need graphical user interface(GUI). How can I install gui in ubuntu server 10.04.
View 5 Replies
View Related
Jan 7, 2011
I'm having an odd problem with Server 10.04. I have two interfaces but only one interface is brought up on boot - and it's not always the same interface. Usually eth0 fails and eth1 comes up fine, but sometimes eth1 fails and eth0 comes up. I'm using the same config that was previously used on Server 8.04, but never had this problem on 8.04.
/etc/network/interfaces:
Code:
# The loopback network interface
auto lo
iface lo inet loopback[code]....
Once the system has booted, if I run /etc/init.d/networking restart, then both interfaces come up fine. However, having read that this is now an upstart, I also tried service networking restart, but get:
Code:
restart: Unknown instance:
Don't know if that's significant or not.
Cannot find a single problem with networking reported in log files, other than bound services failing to start as a result of the interface not being up (dansguardian, squid, dhcp which are all bound to eth0, and therefore fail when eth0 doesn't come up. And when eth1 doesn't come up, the only process that fails to run is clamav-freshclam). Although at one point I did see something about interfaces being renamed which seemed a little odd.
I could just have networking restarted automatically once booted, but this obviously isn't a solution to whatever is causing the problem. There is quite a bit running on the server: Samba/LDAP domain controller with roaming profiles, squid & dansguardian with LDAP auth, postfix & dovecot with LDAP auth, mailscanner, dhcp & ddns, strict iptables policy with nat... so I'm not sure if any of those could have any bearing on interfaces?
View 1 Replies
View Related
Apr 12, 2011
2011-04-11 11:57:03 UTC I don't know what happening with my centralized log-server running octopussy. Currently it is working in a vmware setup with approx 980 Mb ram and is set in bridge mode. Currently is it set to receive logs from logs devices which are 4 in number one of which includes the core isg-1000 device. This setup is still in its test form....now what happens after some time (sometimes it taken days and sometimes just hours) when the connection (https) is suddenly lost to the apache and i can no longer access the interface. What happens more strangely my Ethernet interface gets shutdown on ubuntu. I have to restart the services by issuing /etc/init.d/networking restart.
Even at times it itself start receiving network packets on its own; without even restarting; i don't what the hell is wrong with the server. I cannot understand its erratic behavior. I need a sound and reliable Ethernet connectivity at all times because coz of loss of connectivity in my case would mean loss of logging functionality. I dnt want any time-gap in logging ...as im currently logging some highly critical devices on this server.
View 8 Replies
View Related
