I recently installed a new CPU and motherboard in my Media Server, but the ethernet port isn't showing up under ifconfig. Is there any way to install additional drivers? EDIT: The model is Realtek RTL8111/8160B.
View 3 Replies
I have installed ubuntu, xubuntu on this laptop with usb drives and even net install wont work. Once the os gets installed i see no indication that the ethernet is even there...
lspci:
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
[Code]...
My wireless works with Broadcom support. The ethernet has never worked, i think when windows was still on it, it did.
with my other ethernet card problem solved, I suddenly run into this:
Code:
eth1
Link encap:Ethernet HWaddr 00:02:e3:16:37:4c
inet addr:10.0.2.1 Bcast:10.0.2.255 Mask:255.255.255.0
inet6 addr: fe80::202:e3ff:fe16:374c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code]...
This card was working perfectly fine up until....an hour ago and it started doing this. My iptables isn't blocking it somehow, because I didn't change anything. I tried reverting to an older kernel and that didn't help. It's not the network cable, it works fine in any other card. Also, the dropped packets seem to count down? It seems to go down by exactly one every time I run ifconfig, no matter the length of time in between running it.
I absolutely love Lubuntu on VirtualBox. I installed it to my Compaq Mini CQ-10 without issue. However, there are no drivers for the Wireless or the NIC. Ok, so I go to Broadcom and download the drivers. But, when I try to install with the Makefile, Terminal tells me that make is not installed! Now, how do I install my drivers without make?
View 4 Replies View Relatedi have encounter strange situation i have set all my network configuration via /etc/sysconfig/network-scripts/ifcfg-eth0 ,eth0.2 ,eth1 etc ....i have used only once Gnome network manage settings to add routing since then all my network config change although all files mention above showing the same config i have set initially and same for Gnome network Manager.
View 3 Replies View RelatedI'm trying to grok a problem I'm having with an embedded machine. I'm pretty sure I can track down the larger problem, but I came across a usage of ifconfig that I don't understand, and I'm pretty sure this is the command that is failing.
The command is: ifconfig eth0 192.168.78.20:9134
I understand how ifconfig works. What I don't understand is the :9134. I can't see anything in the docs about what this means. I know in most contexts it's a port number, but what does it do when bringing up a network interface? Does it limit it to only using port 9134?
I have installed CentOS. I have two ethernet card (one onboard and one PCI). I am able to set ip for realtek ethernet card and my atheros(on board) is not shown in network ifconfig shows only one ethernet card (PCI) hen i gave the command lspci i got the following output
01:00.0 Ethernet controller: Atheros Communications AR8132 Fast Ethernet (rev c0)
03:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
i have an embbeded hardware that uses bootp for booting from a Network Managemnt Host (NMH)on the same ethernet. The embedded hardware has both kind of ports i.e ethernet as well as E1/T1. I would like ask, what do i require to establish a communication-link between the embedded hardware and the NMH throuh E1/T1 ports of embedded hardware, so as to make it boot through from E1/T1. Further, NMH possesses only ethernet port. Just to refine my questions i'd like to know what additions do i need to do on my NMH , like may be i have to put an E1/T1 port or is it possible that the E1/T1 port can be directly connected to an ethernet port on the other host.
pardon me if i am not making absolute sense here as my knowledge is limited on Layer 1 and layer 2.
My professor gave me an older ThinkPad, i1161, because he wants me to learn linux. So far, I successfully downloaded Hardy Heron onto the computer, using the Alternate version. Everything works great, and I can log on, play games, go into word processor, the whole nine yards. Unfortunately, the computer won't connect to the ethernet cable that I have plugged in. I am not sure what I am doing wrong, but that is probably because I don't know where to begin.
I also get an error message during boot, it says "ACPI no DMI Bios year" then it says "ACPI=force is required to enable ACPI. I don't know what this means, but I fugured it might have something to do with the ethernet.I am connecting through my University internet. Also, under Network Settings ->Connections, it only has one option, "Point to point connection" and it says "This network interface is not configured."
I am running 11.04 on a Dell Inspiron 1501 (the first gen.). I was using my Ethernet port to connect to the internet until about two weeks ago - suddenly the system no longer recognised that port even existed and just kicked me offline. I am able to get online now with a wireless card (replaced the broadcom card, that was a whole different can of worms...).
why my system is unable to connect with the Ethernet port? If I plug in the cable nothing happens.
I can't figure this out for the life of me. I am new to Linux too. Wireless works fine. I plug my Ethernet in and turn off wireless and I cant surf the web, download, etc...Network Manager finds the wired network under eth0 and it works perfect on my non-linux desktop (nervous to even mention Vista around here). Firewall was set up with basic setup (I didn't make any changes). I have a Sony vaio VPCCW21FX with fedora 13. Can anyone point me in the right direction?
View 10 Replies View RelatedI have a Dell Studio 1501 Laptop and I want to bridge the wireless with the ethernet port so I can hook my xbox360 to my laptop.
I've spent the last 2 hours trying different techniques but nothing is working.
I'm running Ubuntu 9.10 so the last thing I tried was going into the network manager, clicking on wired, editing the ethernet port and allowing it to share. This did nothing.
I tried to share the connect with firestarter but that did not work either.
I am using ubuntu 9 but unable to connect to internet via my usb Siemens c110 modem. I have a dual boot system of both windows7 and ubuntu9. I am using the same modem in windows7 and have installed virtualbox where i have installed the same ubuntu9 but there it automatically detects the wired connection(usb)[eth0] but in the actual boot it doesnt detect anything. I have typed in the terminal sudo ppconfig but it was unable to find anything.
View 1 Replies View RelatedI am running Ubuntu 11.04 and i am curious to if there is a way to share my established wireless connection through my Ethernet port.. I know it was possible in Windows by going to adapters and bridging the wireless, and Ethernet adapters. how to make this work in Ubuntu?
View 1 Replies View RelatedI have installed Ubuntu 11.04 on my Lenovo B570 in a dual boot config alongside Windows 7. I've downloaded the correct Broadcom STA drivers (the model is Broadcom BCM4313) with another PC, transferred them with a USB stick, installed them with Synaptic and locked the version as was recommended. I've also used the rfkill command to turn off the software block, so both hardware and software switches are OK.
The problem is when I go to the "Additional Drivers" application, it yells at me for not having internet access, and then shows up completely empty. This confuses me because I've manually installed it, so I would think it would show up regardless, but it doesn't. In a final effort to make it happy, I've brought it to work and connected it through the Ethernet, setting up the proxy LAN settings to let it through the firewall. I can get on the web with Firefox with that method, however when I launch "Additional Drivers", it sits there searching for drivers endlessly, so I'm guessing it's not really connected. I feel like I'm really close here - I just need to enable the Broadcom driver, but I can't because "Additional Drivers" won't show it.
it was working but after i installed updates and rebooted it could not get a ip address seems like strange timing it still registers under ifconfig it is not even working on the live usb anyway i can test to be sure it is the chip?
View 3 Replies View RelatedI changed to a 4 port ethernet router (D-Link DSL-2542B Adsl2+)with intention to share Internet access with my brother (he's on Vista).Initially it all went well,but 3 days ago there were connection problems occured on the part of the ISP. Without realized the problem,I had reset the router.This morning I've been informed by the ISP that the connection has been re-established.So,I accessed the Internet via the 4 port router but failed to do so (server not found).Suspecting that the problem was from the 4 port router,I reverted to my old Adsl router (DSL-520B single port) and without any problem I managed to access the Internet back.I really need help to configure back the 4 port ethernet router to its initial state.
View 9 Replies View RelatedI'm running an ubuntu maverick server, and I'm having a slight problem with networking. I've only got one ethernet line running into my room, and I've got loads of computers. The server has 2 ethernet ports, one integrated into the motherboard, one on a PCI card that I took from my old server. The on board ethernet never worked on my old server- but I only tried it out post-install, it was hooked up to the card during install (For the record, networking on linux has *never* worked for me if I installed then plugged in the networking stuff after the fact). So I just used the card instead. Transferred the hard drive into a new machine, and lo and behold, it would only work after I transferred in the card from the old one. What I wanted to set up is a basic NAT system, where the network connection is routed through from my server to my main desktop- but when I run ifconfig, my card is not detected, just lo and eth0. How can I fix this?
View 3 Replies View RelatedI am using Ubuntu 10.04 Lucid and VMware 2.0 server. I have a an XP virtual machine that is needed for work. When I am at home and I place my cat 5 cable to my cisco catalyst switch, my XP VM recognizes the ethernet card on my laptop and bridges fine with ubuntu and works fine and I can get to my network. When I take my laptop to work and I go to a site and I plug it into a World Wide Packet 311 management port on the switch, my XP Virtual Machine does not see the network no matter what setting I set it too(100 full, 10 full, 10 half and etc). It simply says that the network card is disconnect. Ubuntu see the network fine and I can ping and talk to the network without any issues but the VM does not.
View 2 Replies View RelatedI am getting the hang of IPTables.I've setup to open certain UDP ports but they simply refuse to show when I iptables -L.
iptables file:
$IPT -A INPUT -p udp --dport 13000 -j ACCEPT
$IPT -A INPUT -p udp --dport 13001 -j ACCEPT
[code]....
I get this ifconfig output for eth0:1 :
eth0:1
Where are all the packet statistics?
I reinstalled ubuntu and now there isn't a box that pops up saying "restricted drivers" where my wireless would pop up saying something like Broadcom STA wireless driver. and Broadcom BZ3 wireless driver (or something like that) I would then click STA wireless driver and click "activate" then it would make my wireless card work.
Why isnt this box popping up? how do I get to it?
I have a simple server running Ubuntu Server. Usually the server connects to the network by Wifi, so there is usually no cable connected to the Ethernet port. I noticed that there is a dhclient3 running on eth0 anyway. It is causing undesirable disk activity. Obviously, it is never going to get a response as long as no cable is connected. I can kill the responsible process manually, but I wonder first what is starting the process and how I can prevent it from being started. If there is a way to get the server to boot without starting this process, I wonder whether this is the right solution. Connecting to the network by Ethernet is the failsafe when Wifi doesn't work. I guess what I would like to see would be a way for the server to detect when eth0 does not have a cable connected and not start dhclient in that case, but to activate dhclient when a cable is connected.
View 4 Replies View RelatedI have a server in a colocation environment where I'm allotted 25Mbps. I'd like to avoid exceeding that for obvious reasons. Is there a way I can set the link speed or at least throttle the bandwidth for all services?
View 2 Replies View RelatedI'm currently using Ubuntu 9.1, and a motherboard which has two Ethernet ports on it.
What I would like to do is bridge these ports, so I can plug in another Ethernet cable and run it to an unmanaged switch in my room (handy for my work laptop when on-call and building other PCs, etc).
I.e. Router --> 8-Port Switch --> My PC.
Eth 0 --> 192.168.1.100 static
Eth 1 --> 5-Port Switch --> DHCP
I believe this is the config to make the ports bridged:
ifconfig Eth0 0.0.0.0
ifconfig Eth1 0.0.0.0
brctl addbr Bridge0
brctl addif Bridge0 Eth0
brctl addif Bridge0 Eth1
ifconfig Bridge0 up
- How do I save this so upon reboot it sticks?
- How do I force Eth0 to remain as a static IP of 192.168.1.100?
I have a Dell WLAN 1397 Half Minicard, 802.11 b/g card in my laptop, and I can't seem to get ubuntu to work with it. I tried this method:
1. Synaptic Pack Manager
2. Check "Install from Boot Disc"
3. Reload
4. Install and apply bcmwl-kernel-source
5. Reboot
This didn't work for me, so I tried entering sudo apt-get install bcmwl-kernel-source and that also didn't work. Another thing I tried is formatting my Ubuntu partition and reinstalling, and retrying both of those methods. The ethernet port does work, however.
I'm been wanting to try Ubuntu for a while now, and when my mom's netbook started to get insanely slow with WinXP, I tried the Netbook Remix on a USB stick. I LOVE it, except I am unable to get the wireless working, which is the only thing stopping me right now from a full install.
I believe my problem is that I need to activate the two drivers "Broadcom B43 wireless driver" and "Broadcom STA wireless driver" which appear as unactivated when I go into the hardware drivers admin tools. Unfortunately this netbook (HP Mini Netbook FW376UA) does not have an Ethernet port, so I can't just temporarily hard wire it to activate these drivers.
So my main questions are: 1) How can I activate those drivers without an internet connection?, and 2) Do you think that activating these drivers is indeed the answer to getting the wireless working?
The details:
Machine: HP Mini Netbook FW376UA
Network Controller: Broadcom Corporation BCM4312 802.11b/g
Ubuntu version: Ubuntu 10.04 Netbook
have a toshiba satellite L745 running Lucid Lynx I need drivers for the Atheros AR8151 ethernet card. Every post I have read on installing the driver give links to Atheros but they are all broken. Does anybody know where I can download driver?
View 9 Replies View RelatedI want to transfer the audio file on linux machine using Ethernet port, is it possible?
View 6 Replies View Relatedwhile my brother was browsing the web on my windows partition he had a blue screen pop up, one of the soft/hardware error ones, not a true BSOD, anyways, ever since my lan port on the computer seems to not be activiating as no wired connection is recognized. The lan port/card is directly attached to the Mother Board, it's a gigabyte motherboard in a self-build computer. I'm just wondering if there's anything I can do to troubleshoot this and see if it is truly a hardware problem or if its something else.
View 9 Replies View Related
