I have static eth1 defined. When I boot or restart, the networking will not start automatically - i must do it from terminal by ifup eth1.
Where can I put this command to have it autostart?
I am trying to attach my server to 2 diferent networks, with fixed ip addresses,
eth0 = 192.168.0.2 255.255.255.0 with gateway 192.168.0.1. This is currently working, and I can ssh o the machine on this address
eth1 = 192.168.150.5 255.255.255.0 with gateway 192.168.150.1
When I try and start eth1 with ifconfig eth1 up, I get the error message "eth1: unknown interface: no such device"
I have configured eth1 using system-config-network-tui and /etc/sysconfig/networking/devices/ifcfg-eth1 looks correct
GATEWAY=192.168.150.1
TYPE=Ethernet
DEVICE=eth1
BOOTPROTO=none
[Code].....
I need to setup two ethernets in my Centos box. OK no problem both ethernet and 1 virtual works perfect. eth0, eth1 and eth1:0. I'm trying to set up diferent routes for eth0 and eth1/eth1:0 I need eth0 has a 192.168.1.1 gateway and eth1/eth1:0 192.168.1.100 gateway.I think I've tried almost every thing but always get one gateway for all the eth.These are my config..
/sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:XX:XX:XX:XX:XX
inet addr:192.168.1.168 Bcast:192.168.1.255 Mask:255.255.255.0[code]......
I try to generate a server client code. What i try to do is sending video streams from eth0 and eth1 to the other server programs' eth0 and eth1. In order to do that, i decided to use SO_BINDTODEVICE. But the code is not working. Am i misunderstood the usage of SO_BINDTODEVICE.
1-Defining two ports
2-Defining two sockets
3-Assigning host ips on them
[code]....
Since I've updated to 9.10 my avahi-daemon sometimes won't start at boot.I've to "restart" it manually.I reinstalled it without success.Has anyone here the same problem? Or a useful solution?
View 1 Replies View RelatedWhen i start up the wireless is disabled automatically.
View 3 Replies View RelatedI have a Centos 5.4 server, I would like to know how to start NFS automtically when the server boots up so that I won't have to manually start the service after the server boots up. where and how do I accomplish this?
View 3 Replies View RelatedI have a new HP G62-352CA with the Realtek 8191SE wireless. I am running Ubuntu 10.10 everything works fine except every time I restart the computer I have to press fn f12 to restart the wireless. Is there a way to have it default on at startup?
View 3 Replies View Relatedi use ubuntu 10.10 installed in wubi on my girlfriend's machine.in order to connect to the internet i had to install a dialer script and then i need to type in terminal: sudo cable-start and then password BUT i wish this to happen automatically when booting the machine.i am sure that it is possible, but have no clue how to do it.
View 3 Replies View RelatedAfter an upgrade to 2.6.27.25-78.2.56.fc9.i686 in March, my Atheros wireless stopped working. (It had previously run without a hitch for 9 months). Anyway, I finally got around to working on it today and using the "WiFi misery" thread managed to consistently get it to start manually via these steps:ifconfig wlan0 up
iwconfig wlan0 essid netname key xxxxxxxxxxxxx
click on "activate" in network device control (gives error msg, but works)
During boot-up, I get "Invalid argument" errors for "SET MODE", "SET BIT RATE", and "SET ENCODE".Currently NetworkManager service is disabled, but when enabled doesn't seem to change any of the above.I'd like to get back to automatically coming up wireless, if possible.
what to do for lock automatically slackware 13 if not used for n minutes ?What can i do to start automatically the ktorrent (a bittorrent program for linux) on system starts on slackware 13 ?
View 2 Replies View RelatedI have a hardware device with two ethernet ports, eth0 and eth1 running Centos 5. Basically my goal is to forward packets from eth0->eth1 and eth1->eth0 as well as get a copy of these packets for analysis. If I set IP routing to do the forwarding then I won't get a copy of the packets for analysis.
View 3 Replies View RelatedIm trying to run synergy on startup. This works fine on the client, but it wont start automatically on the server. I put this line in an entry in startup applications:
[code]...
but still no dice.
I use Opensuse 11 with fvwm. How can I get conky start automatically when I start fvwm?
I setup the conky under fvwm session for my Opensuse 11 but it won't start automatically. I am wondering how to write some kind of scripts to force it to start automatically and with a delay about 10 seconds after fvwm starts.
I am running Ubuntu10.04 as a Virtual Machine in virtualbox.I changed my Networking settings from NAT to Bridged Adapter and manually assigned IP addressing information for eth0 in /etc/network/interfaces. For some reason doing /etc/init.d/networking restart didn't bring up the network interface. So i replaced the new /etc/network/interfaces file with the original and rebooted. Now I have eth1 in place of eth0. Under System>Preferences>Network Connections I have Auto Ethernet and eth0. However running ifconfig shows lo and eth1.
View 9 Replies View RelatedMy wireless suddenly no longer works either in Ubuntu 10.10 or Windows 7. Upon some investigation, I have found that my eth1 is no longer showing up as it used to.
What can I do to get my wireless back?
Right below is some current specs, while below that is an older set of specs from a while ago.
Code:
sef@sef:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
[Code]....
I'm having a strange problem. I'm using Ubuntu server 10.04 LTS and I want to setup a system with 2 network interfaces: eth0 and eth1. However eth1 does not come up at boot I have a screenshot of my /etc/network/interfaces file I don't see what is wrong. eth0 gets it's adress from DHCP eth1 gets a static adress. When i try to restart networking it quits with this message "don't seem to be have all the variables for eth1 inet" Can anyone point out what I'm doing wrong? if i do 'sudo ifconfig eth1 192.168.3.1 netmask 255.255.255.0 up' eth1 comes up
View 3 Replies View RelatedI am working on USB Connectivity between android 2.1 Host and Windows Mobiles 6.1 device...When I connect the windows mobile device to android host through USB (in RNDIS Mode), It is appearing as 'eth1' interface instead of 'usb0' interface. Why 'eth1' instead of 'usb0' ? Does behaviour of 'eth1' is same as 'usb0'?
View 8 Replies View RelatedHow can I configure ssh to only listen to eth1?
View 4 Replies View Relatedhow can I change eth1 mac address permanently in an easy way?
View 1 Replies View RelatedIt is. I think this might be the reason why my $wireless objects don't work in Conky?
View 4 Replies View RelatedI have an older laptop, a Toshiba Satellite Pro 6100 that has a switchable internal wireless connection. It will not connect to my router. I am using the 10,04 netbook remix. When I use lshw in terminal this is what I get:
*-network
description: Wireless interface
physical id: 1
logical name: eth1
[Code].....
Should it not be identified as wlan0? I know a whole lot about Ubuntu linux because I don't. I did a clean install over XP and am using this laptop as a learning tool for linux in hopes to divorce windows completely.
I have a bit of a "unique" situation here. I have myself plugged into two networks - since we run two networks here at work (long story, we merged and never combined them due to two different companies) and want to block ALL internet access off eth1, and only have it off eth0. I only want traffic from 192.168.67.1-192.168.67.255 allowed on eth1, but everything allowed on eth0. Or is there a way for the internet/applications to be on eth0 instead of eth1? Would I use iptables or something?
View 4 Replies View Relatedim a linux noob dont get techy ill die of brain fry im running a craft bukkit minecraft server on my 11.04 ubuntu server. however the server uses my only 10m Ethernet cable that i normaly use for my ps3 (i will NOT go wireless. i hate it (or dont like it)) therefor i found an old PCI NIC in an old computer, its a 10/100 realtek one. ifconfig detects it (after two commands:
Code:
ifconfig eth0 up
dhclient eth0
)
now i need to send the internet to my ps3 too.i know the connection wont be blazing fast but isnt it okay?it musnt interrupt the minecraft server. if you need info just ask. ill try and provide them.
I've noticed that when Linux boots on different machines or with different versions, the network card is assigned to eth0 or to eth1, when there is only one network card. What is the difference and is there any way to tell which one it will be for any machine or version?
View 2 Replies View RelatedI often run "gulp", a networking utility, to capture data from an instrument on "eth1". By default gulp must be run as root to have access to the ethernet port, and when I'm the only one running it, that's fine. But I need to let several other users to capture data and don't want to give them all sudo permissions for both gulp, and more importantly, 'chmod'. Is there anyway to change the permissions of eth1 to allow all users to open it and avoid sudo entirely? This is on a Red Hat/Fedora machine.
View 1 Replies View RelatedI installed Slackware 13.37 console only.
I have two ethernet cards.
I want to change eth1 to eth0 and eth0 to eth1, because I have some old firewall script and I need eth0 be eth1, because of routing internet. My ISP close my net connection on MAC adress.
I am trying to setup linux box as router.
What i am trying to do is:
1. I am trying to setup NIC via network not NetworkManager
2. I have assigned the ip to both NIC with #ifconfig eth0 192.168.1.1
3. #Ifconfig shows my nic and ip
4. restart the service network .
5. #ifconfig shows nothing. NO NIC card
I dont want the network manager coz i dont want to install the gui on router and network manager works only in gui mode. ( i think my this understanding is correct)
I tried to configure the NIC with Network Manager
When ever i restart the network service i have no out put from ifconfig
I tried to configure the NIC with #setup command as well and select the dhcp option
I can not find any ifcfg-eth0 in /etc/sysconfig/networking-scripts/
I upgraded to 10.04 and my AWN dock won't automatically start even though the 'box' is tic'd and it's showing in the Startup Applications. I did lose all of my configurations as well after upgrading and had to reinstall everything on the dock.
Also, there are little numbers on the launchers like for Trash and Email that tell me how many items are in there. The Trash was easy to remove the numbers by right clicking and choosing the Preferences option. There was a place to disable that but there isn't one for the Email and those little numbers look well.
After restart or suspend/resume the Wifi won't start until I click on my home network from the menu. It used to start without me doing anything (once I setup the wireless).
View 1 Replies View Related