Networking :: 'eth1' Instead Of 'usb0'

Jun 1, 2011

I am working on USB Connectivity between android 2.1 Host and Windows Mobiles 6.1 device...When I connect the windows mobile device to android host through USB (in RNDIS Mode), It is appearing as 'eth1' interface instead of 'usb0' interface. Why 'eth1' instead of 'usb0' ? Does behaviour of 'eth1' is same as 'usb0'?

View 8 Replies


ADVERTISEMENT

CentOS 5 Networking :: Eth0, Eth1, Eth1:0, Route = Get One Gateway For All The Eth?

Mar 4, 2011

I need to setup two ethernets in my Centos box. OK no problem both ethernet and 1 virtual works perfect. eth0, eth1 and eth1:0. I'm trying to set up diferent routes for eth0 and eth1/eth1:0 I need eth0 has a 192.168.1.1 gateway and eth1/eth1:0 192.168.1.100 gateway.I think I've tried almost every thing but always get one gateway for all the eth.These are my config..

/sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:XX:XX:XX:XX:XX
inet addr:192.168.1.168 Bcast:192.168.1.255 Mask:255.255.255.0[code]......

View 7 Replies View Related

Red Hat / Fedora :: XEN And Networking - Interface Comes Up As USB0

Apr 19, 2010

I'm running CentOS 5.4 and have problems with a USB-Ethernet network interface. It works in another, very similar environment but now I added Virtualization when installing the system. The interfaces comes up as usb0 - as usual, and I'm sending and receiving packets (PPPoE) but there seems to be a link missing so that the ppp session can be build. I wondered if this has to do with the Xen virtual environment running which installed a lot of virtual interfaces and bridges, but not for the USB interface.

The problem is that for PPPoE server, the interface must not have an IP address assigned - not an option when creating a new host interface. But even when I do so, the interface seems unlinked somehow. Funny thing, I can monitor the incoming and outgoing packets using Wireshark. I have not (yet) set up a virtual machine/guest system but the default machine is running.

View 1 Replies View Related

Ubuntu Networking :: 10.04: Unable To Use Eth0 And Usb0 At The Same Time?

Nov 20, 2010

I have no telephone connection at home, so I use my cellphone to connect to the internet. Network manager reports this interface as a "wired connection", usb0, using the cdc_ether driver.I also have a router at home, so I can connect my netbook to my desktop wirelessly. My desktop computer connects to the router via ethernet connection, and network manager reports it as eth0.

When I had Ubuntu 8.04 installed on my desktop, I could use my phone, via usb0 interface, to connect to the internet at the same time as using the router on eth0. But now I have 10.04 on the computer, and it won't let me use both interfaces at the same time: I have to unconnect the router before I can use usb0.

View 1 Replies View Related

Networking :: Sending Video Streams From Eth0 And Eth1 To The Other Server Programs' Eth0 And Eth1?

Jul 30, 2010

I try to generate a server client code. What i try to do is sending video streams from eth0 and eth1 to the other server programs' eth0 and eth1. In order to do that, i decided to use SO_BINDTODEVICE. But the code is not working. Am i misunderstood the usage of SO_BINDTODEVICE.

1-Defining two ports
2-Defining two sockets
3-Assigning host ips on them

[code]....

View 3 Replies View Related

Networking :: Kernel - Forward Packets From Eth0 To Eth1 And Eth1-to Eth0 As Well As Get A Copy Of These Packets For Analysis

Sep 27, 2010

I have a hardware device with two ethernet ports, eth0 and eth1 running Centos 5. Basically my goal is to forward packets from eth0->eth1 and eth1->eth0 as well as get a copy of these packets for analysis. If I set IP routing to do the forwarding then I won't get a copy of the packets for analysis.

View 3 Replies View Related

Ubuntu Networking :: Android USB Tether "ifconfig Does Not Find A Usb0 Device" And Server

Jan 3, 2011

I am currently trying to get my server box to recognize my Samsung epic 4g (sprint) which is rooted and has usb tether enabled. It works perfectly and effortlessly on my ubuntu desktop box, but I hook it up to my server box and ifconfig does not find a usb0 device like my desktop does. I am running 10.4.1 on both desk and server box.

View 1 Replies View Related

Ubuntu :: Get An Error Message That Usb0 Is Not Available?

Apr 23, 2011

I connect my mobile phone to Ubuntu and I get an error message that usb0 is not available. Here is the log:

Code:
--------------- System information ----------------
Platform linux2

[code]...

View 1 Replies View Related

Ubuntu :: USB Automounts With Root Privileges As /media/usb0?

Oct 25, 2010

not sure if this is a silly issue or what. I recently upgraded to 10.10. When I insert my usb device, it automounts as /media/usb0, with root privileges. I have to manually unmount it, and afterwards if I select the "mount (drivename)" usb stick from Places it will automount as /media/(devicename) with proper

View 2 Replies View Related

Networking :: Ssh Listening Only To Eth1

Sep 18, 2010

How can I configure ssh to only listen to eth1?

View 4 Replies View Related

Ubuntu Networking :: Eth1 On Computer With Only 1 NIC?

Jan 11, 2011

I am running Ubuntu10.04 as a Virtual Machine in virtualbox.I changed my Networking settings from NAT to Bridged Adapter and manually assigned IP addressing information for eth0 in /etc/network/interfaces. For some reason doing /etc/init.d/networking restart didn't bring up the network interface. So i replaced the new /etc/network/interfaces file with the original and rebooted. Now I have eth1 in place of eth0. Under System>Preferences>Network Connections I have Auto Ethernet and eth0. However running ifconfig shows lo and eth1.

View 9 Replies View Related

Networking :: Eth0 Or Eth1 - What Is The Difference

Nov 30, 2010

I've noticed that when Linux boots on different machines or with different versions, the network card is assigned to eth0 or to eth1, when there is only one network card. What is the difference and is there any way to tell which one it will be for any machine or version?

View 2 Replies View Related

Networking :: Changing The Permissions Of Eth1

Sep 14, 2009

I often run "gulp", a networking utility, to capture data from an instrument on "eth1". By default gulp must be run as root to have access to the ethernet port, and when I'm the only one running it, that's fine. But I need to let several other users to capture data and don't want to give them all sudo permissions for both gulp, and more importantly, 'chmod'. Is there anyway to change the permissions of eth1 to allow all users to open it and avoid sudo entirely? This is on a Red Hat/Fedora machine.

View 1 Replies View Related

Networking :: Switch Eth1 To Eth0 ?

May 4, 2011

I installed Slackware 13.37 console only.

I have two ethernet cards.

I want to change eth1 to eth0 and eth0 to eth1, because I have some old firewall script and I need eth0 be eth1, because of routing internet. My ISP close my net connection on MAC adress.

View 2 Replies View Related

Fedora Networking :: 12 - Networking Eth0 And Eth1

Jan 12, 2010

I am trying to setup linux box as router.

What i am trying to do is:

1. I am trying to setup NIC via network not NetworkManager
2. I have assigned the ip to both NIC with #ifconfig eth0 192.168.1.1
3. #Ifconfig shows my nic and ip
4. restart the service network .
5. #ifconfig shows nothing. NO NIC card

I dont want the network manager coz i dont want to install the gui on router and network manager works only in gui mode. ( i think my this understanding is correct)

I tried to configure the NIC with Network Manager

When ever i restart the network service i have no out put from ifconfig

I tried to configure the NIC with #setup command as well and select the dhcp option

I can not find any ifcfg-eth0 in /etc/sysconfig/networking-scripts/

View 6 Replies View Related

Ubuntu Networking :: No Wireless - Eth1 Has Disappeared?

Jan 16, 2011

My wireless suddenly no longer works either in Ubuntu 10.10 or Windows 7. Upon some investigation, I have found that my eth1 is no longer showing up as it used to.

What can I do to get my wireless back?

Right below is some current specs, while below that is an older set of specs from a while ago.

Code:
sef@sef:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)

[Code]....

View 2 Replies View Related

Ubuntu Networking :: Don't Seem To Have All Variables For Eth1 Inet

Apr 28, 2011

I'm having a strange problem. I'm using Ubuntu server 10.04 LTS and I want to setup a system with 2 network interfaces: eth0 and eth1. However eth1 does not come up at boot I have a screenshot of my /etc/network/interfaces file I don't see what is wrong. eth0 gets it's adress from DHCP eth1 gets a static adress. When i try to restart networking it quits with this message "don't seem to be have all the variables for eth1 inet" Can anyone point out what I'm doing wrong? if i do 'sudo ifconfig eth1 192.168.3.1 netmask 255.255.255.0 up' eth1 comes up

View 3 Replies View Related

Ubuntu Networking :: Eth1 Does Not Start Automatically

May 2, 2011

I have static eth1 defined. When I boot or restart, the networking will not start automatically - i must do it from terminal by ifup eth1.

Where can I put this command to have it autostart?

View 5 Replies View Related

Networking :: Server (eth1-connecting To The Windows XP PC) = 192.168.4.3?

Apr 1, 2011

I have the following setup: An ADSL Router (192.168.4.1) which plugs into my server (that has 2 network cards) Server(eth0-connecting to the ADSL Router) = 192.168.4.2 Server(eth1-connecting to the windows XP PC) = 192.168.4.3 And the windows XP PC = 192.168.4.4 if I delete the entire routing table and add a default route route add default gw 192.168.4.1 dev eth0 I get an error (I can't remember the error, the PC's at work) however if I unplug the cable going from the PC to eth1, I can then successfully add the default route, and I can ping the router, however when I reconnect the cable to the PC and Server... I can still ping the router (from the server) but I cannot ping the PC

if I try and add another route such as: route add -net 192.168.4.0 netmask 255.255.255.0 gw 192.168.4.4 it wont let me add the rule I have a feeling i am doing something really stupid here with the addressing scheme,

View 2 Replies View Related

CentOS 5 Networking :: 5.1 Won't Recognize 2nd Nic Card Eth1

Jun 5, 2009

i have installed centos 5.1 but it won't recognize 2nd nic card (eth1). i was unable to install the driver supplied by the cd. i am using intellinet gigabite pci network card. the network card recognize by centos 5.3 but i need to use centos 5.1. i also tried another intel gigabite adopter but it also won't recognize by centos 5.1.

View 2 Replies View Related

Fedora Networking :: Change Eth1 Into Eth0 And Viceversa?

Apr 3, 2009

I have two network devices :

1. Intel Corporation 82574L Gigabit Network Conncection (Currently eth0, Mac=00:0e:8c:ab:c6:b1)

2. National Semiconductor Corporation DP83815 (Currently eth1, Mac=00:0e:8c:8a:70:62)

I want to change them so that the "Intel" become eth1 device and the "National" become the eth0 device.

I already tried these steps :

1. I disabled the Network Manager and enabled network

2. Edit the /etc/udev/rules.d/70-persistent-net.rules like this

Quote:

3. Change the /etc/sysconfig/network-scripts/ifcfg-eth0 and /etc/sysconfig/network-scripts/ifcfg-eth1 MAC addresses.

4. Reboot

5. After it bootup the Fedora can't recognize the devices, if I do ifconfig -a it shows "eth0_rename with FF:FF:FF:FF:FF:FF mac address".

View 3 Replies View Related

Fedora Networking :: Why Primary Interface Is Eth1 Instead Of Eth0?

Jan 31, 2010

I have two network interfaces on my computer but only one of them is connected to an Ethernet cable. Until now on every Fedora release, the activated primary interface has been named as eth0 and everything has always worked well without any problem. Recently I switched to Fedora Core 12 and surprisingly I observed that for the first time, my primary interface has been considered by the system to be eth1 instead of eth0. I tried to replace the content of ifcfg-eth0 by ifcfg-eth1, yet system gave me an error that there was MAC address mismatching. I conserved their MAC addresses in their files and just replaced other connection parameters ( such as IP ADDR, NETWORK, NETMASK, etc.) but it did't work. When I do "server network restart", the command blocks.

As I try to install oracle on this system, regarding the fact that oracle requires static network configuration on the primary network interface, I don't know how to proceed in order to set eth0 as my primary interface (or rather set the current eth1 to eth0 because it is actually eth1 that refers to my activated primary network card).Just one more time, I would like to remark, that with previous versions of the Fedora Core, on the same computer (with the very same two network cards) I never had problem and I had installed oracle on the system with success, having the statically configured eth0 correctly detected by the system.

View 2 Replies View Related

Ubuntu Networking :: Change Eth1 Mac Address Permanently 9.10?

Jan 22, 2010

how can I change eth1 mac address permanently in an easy way?

View 1 Replies View Related

Ubuntu Networking :: Should Wireless Be Labeled As Eth1 In Ifconfig

Jan 31, 2010

It is. I think this might be the reason why my $wireless objects don't work in Conky?

View 4 Replies View Related

Ubuntu Networking :: Internal Wireless Listed As Eth1?

Jul 13, 2010

I have an older laptop, a Toshiba Satellite Pro 6100 that has a switchable internal wireless connection. It will not connect to my router. I am using the 10,04 netbook remix. When I use lshw in terminal this is what I get:

*-network
description: Wireless interface
physical id: 1
logical name: eth1

[Code].....

Should it not be identified as wlan0? I know a whole lot about Ubuntu linux because I don't. I did a clean install over XP and am using this laptop as a learning tool for linux in hopes to divorce windows completely.

View 7 Replies View Related

Ubuntu Networking :: Stop Internet Access From Eth1?

Aug 24, 2010

I have a bit of a "unique" situation here. I have myself plugged into two networks - since we run two networks here at work (long story, we merged and never combined them due to two different companies) and want to block ALL internet access off eth1, and only have it off eth0. I only want traffic from 192.168.67.1-192.168.67.255 allowed on eth1, but everything allowed on eth0. Or is there a way for the internet/applications to be on eth0 instead of eth1? Would I use iptables or something?

View 4 Replies View Related

Ubuntu Networking :: Sharing The Internet From Eth0 To Eth1?

May 11, 2011

im a linux noob dont get techy ill die of brain fry im running a craft bukkit minecraft server on my 11.04 ubuntu server. however the server uses my only 10m Ethernet cable that i normaly use for my ps3 (i will NOT go wireless. i hate it (or dont like it)) therefor i found an old PCI NIC in an old computer, its a 10/100 realtek one. ifconfig detects it (after two commands:

Code:
ifconfig eth0 up
dhclient eth0
)

now i need to send the internet to my ps3 too.i know the connection wont be blazing fast but isnt it okay?it musnt interrupt the minecraft server. if you need info just ask. ill try and provide them.

View 1 Replies View Related

Networking :: Cable Disconneciton Eth0 And Eth1 Behaviour

Mar 10, 2010

I need to have the configuration showed on the attached file. I have two machines, one PC (ubuntu 9.10 ) and one embedded CPU with a tailored linux version starting from 2.4.31 linux kernel with Busybox running on PPC architecture.

PC address is 192.168.30.70.

On CPU board I have two ethernet interfaces with addresses :
eth0 192.168.30.30 netmask 255.255.255.0
eth1 192.168.30.40 netmask 255.255.255.0

PC sends messages alternatively to 192.168.30.40 and to 192.168.30.30 .Between two machines there is an ethernet switch to allow messages flowing.

I use ping (from two shells on PC I ping the two addresses on CPU) to simulate messages from PC to CPU and I see this behaviour:

Starting from a situation in which CPU responds to the pings I try to disconnect cable connected to eth0 on CPU. I cannot see any interruption on ping reply on the eth0 port. If i reconnect the cable on eth0 and I disconnect cable on eth1 there are no reply to the two pings (neither from eth0 nor from eth1). It seems that all data flows on one cable just because the addresses are on the same subnet. Is this right?

If this is the right behaviour how can i separate data from PC to CPU in order to force packets to flow on two cables and avoid this sort of internal routing beetween eth0 and eth1?

View 3 Replies View Related

Networking :: CentOS5.5- Eth1 To Router Ping Is Not Working

Jun 14, 2010

I have static route for eth1:

[Code].....

eth1 (13.3.3.2) is connected to router port 2/0 (13.3.3.1). I am trying to ping from eth1 to router or vice versa. None of them is not working. Don't know what is problem. [root@perseus anvltest]# ping 13.3.3.1 PING 13.3.3.1 (13.3.3.1) 56(84) bytes of data.

3 packets transmitted, 0 received, 100% packet loss, time 2000ms

[Code]....

View 4 Replies View Related

Networking :: Eth0 Works Great - Eth1 Not Working ?

May 14, 2010

Ok, so eth0 is up and working great. eth1, however, comes up with a link light, however the packet counters in ifconfig remain at 0. Appears that eth1 isn't working.

Here's my setup:

-Dell latitude CPi laptop with 2 PCMCIA network cards and no built-in ethernet.
-Slackware v11
-eth0 is connected inside my router on my 192 network. Static address with good connectivity
-eth1 is connected on the other side of my router in promiscuous mode in order to listen to the traffic coming into my network.

Troubleshooting so far: I have switched the pcmcia cards between slots and regardless of which card is in eth0 or eth1, eth0 works and eth1 does not. I have also switched the card dongle between cards as well as the ethernet cabling between the cards. With any of the combinations eth0 works like a champ but eth1 does not, so I think I've ruled out hardware problems.

View 14 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved