Ubuntu Networking :: Internal Wireless Listed As Eth1?

Jul 13, 2010

I have an older laptop, a Toshiba Satellite Pro 6100 that has a switchable internal wireless connection. It will not connect to my router. I am using the 10,04 netbook remix. When I use lshw in terminal this is what I get:

*-network
description: Wireless interface
physical id: 1
logical name: eth1

[Code].....

Should it not be identified as wlan0? I know a whole lot about Ubuntu linux because I don't. I did a clean install over XP and am using this laptop as a learning tool for linux in hopes to divorce windows completely.

View 7 Replies


ADVERTISEMENT

Ubuntu Networking :: Route Internal Ip On Eth1 To External Ip On Eth0?

Dec 9, 2010

Im setting up a server thats connected to a large network. Now my external ip on the network is static and is 10.0.12.15. What I want is to create a dhcp network using the second port of my box. The first port eth0 goes to my network with the static ip 10.0.12.15 and my second port is connected to a switch with the static ip 192.168.12.1. Now dhcp works fine but none of the boxes that are connected to the internal ip cannot connect to the internet. Iv tried using squid and manual static ip routes. Im not using network manager or anything cause its a command line server.

View 1 Replies View Related

Ubuntu Networking :: Rename My Wireless Card From Eth1 To Wlan0 As Use Conkyrc And It Will Not Read Wireless Strength?

Aug 8, 2010

have a dell Inspiron 1501 with ubuntu 10.0.4 I want to rename my wireless card from eth1 to wlan0 as I use conkyrc and it will not read my wireless strength or my ssid cuz it thinks it's a ethernet card and not wireless card. I know this for a fact because peppermint os my wireless card was wlan0 and it worked just fine.

View 1 Replies View Related

Ubuntu Networking :: No Wireless - Eth1 Has Disappeared?

Jan 16, 2011

My wireless suddenly no longer works either in Ubuntu 10.10 or Windows 7. Upon some investigation, I have found that my eth1 is no longer showing up as it used to.

What can I do to get my wireless back?

Right below is some current specs, while below that is an older set of specs from a while ago.

Code:
sef@sef:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)

[Code]....

View 2 Replies View Related

Ubuntu Networking :: Should Wireless Be Labeled As Eth1 In Ifconfig

Jan 31, 2010

It is. I think this might be the reason why my $wireless objects don't work in Conky?

View 4 Replies View Related

Ubuntu Networking :: Eth1 Wireless Connected But Browser Says ERR_name_not_resolved

Apr 26, 2011

installed UB10.10 on a dell d800 laptop with a built in wireless.The eth1 wireless device/connection shows up on the little radio icon as connected .but the chrome browser says "ERR_name_not_resolved" when I enter a common url.What's the next step or hint for gaining full internet access ?

View 4 Replies View Related

CentOS 5 Networking :: Eth0, Eth1, Eth1:0, Route = Get One Gateway For All The Eth?

Mar 4, 2011

I need to setup two ethernets in my Centos box. OK no problem both ethernet and 1 virtual works perfect. eth0, eth1 and eth1:0. I'm trying to set up diferent routes for eth0 and eth1/eth1:0 I need eth0 has a 192.168.1.1 gateway and eth1/eth1:0 192.168.1.100 gateway.I think I've tried almost every thing but always get one gateway for all the eth.These are my config..

/sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:XX:XX:XX:XX:XX
inet addr:192.168.1.168 Bcast:192.168.1.255 Mask:255.255.255.0[code]......

View 7 Replies View Related

Ubuntu Networking :: BTHomeHub2 - Router Not Listed In Wireless Connections

Oct 21, 2010

I'm getting really tired of using windows, I love ubuntu but theres a big problem. I have a BTHomeHub2 and whats annoying is whenever I goto wireless connections there's only a bt home hub but its not my one. and I have tried connecting to hidden wireless network and nothing worked. I have a desktop pc with a usb plug in BT voyager that picks up the router but it will only find the one down the street not mine. It works fine when using Ethernet.

View 2 Replies View Related

Ubuntu Networking :: Cannot Use Internal Wireless Device

Jul 10, 2011

It's been ages since I've been on here I've been messing around with BackTrack. I've come back to Ubuntu but seem to be having some problems getting my wireless network thingy working. Here are the specs of my system. Any advice on fixing this would be very very apprciated.

02:06.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)
02:08.0 Ethernet controller: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile (rev 01)
10:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)

On another note I'm trying to run debain I've got no startx on there or anything like that it's feeling very basic atm. I want to keep startx outta there but I can't connect to the Internet and run apt-get install to grab handy things.

I'm hoping whatever I am gonna do to solve this on Ubuntu will let me connect up to my wireless network with the internal network thingy. However if it doesn't I'm guessin I can just connect up physically to the router. Any tips on doing this from the command line?

View 7 Replies View Related

Networking :: Sending Video Streams From Eth0 And Eth1 To The Other Server Programs' Eth0 And Eth1?

Jul 30, 2010

I try to generate a server client code. What i try to do is sending video streams from eth0 and eth1 to the other server programs' eth0 and eth1. In order to do that, i decided to use SO_BINDTODEVICE. But the code is not working. Am i misunderstood the usage of SO_BINDTODEVICE.

1-Defining two ports
2-Defining two sockets
3-Assigning host ips on them

[code]....

View 3 Replies View Related

Networking :: Internal Wireless As Outside Interface ?

Dec 3, 2010

What i wanted to do was use a linux machine with a wireless and wired interface to act as a router. The wireless interface would be the outside and get its IP via DHCP from the wireless my landlord provides. The wired connection would be for my local pcs. I understand it would be slow having multiple pcs using a single wireless gateway.

View 2 Replies View Related

Ubuntu Networking :: How To Disable Internal Wireless Adapter

May 10, 2011

My Intel 5100 AGN adapter works horribly in Ubuntu. I want to disable it, so I can use a USB wireless adapter that works normally.

I cannot find a reliable way to permanently do this.

View 7 Replies View Related

Ubuntu Networking :: Disable Internal Wireless And Enable External?

Dec 25, 2010

Disable internal wireless card & enable external? Can I do this really by network-manager or should I use some other program. If I plug-in external both are connected. If I disable internal by laptop button, I cannot enable wireless anymore in nm-applett (external on).

View 7 Replies View Related

Ubuntu Networking :: Toshiba A15 S127 Not Seeing New Wireless Card (internal)

Feb 1, 2011

I have a toshiba a15 s127. it didn't have a wireless card so i ordered one and installed it myself. however, my computer is not seeing the wireless card and i don't know what driver i need because the card itself didn't come to me in a box, so i am not sure what brand it is. All i know is that it is an original part.

On another note, when i go to network settings and try to config my wireless settings, i do not know what number to put in the BSSID field. (thinking i use the wireless card's MAC address, but ?) and don't know if i use the wireless card's MAC adress or the wireless router's MAC address or the Modem's MAC address in the actual field for the MAC address. ( i know, i know, i sound totally clueless--well, i am!) {note: the wired network works fine.}

How do i get my computer to see the wireless card and how do i configure my computer once it does see the card?

View 1 Replies View Related

Ubuntu Networking :: Disable Internal Wireless Card To Use External?

Aug 6, 2011

I would like to turn off the internal wireless card since my external wireless card has better signal. Problem is if I turn of the internal card the external card turns off as well. My external card is an alfa awus036h 1000w. Laptop Gateway NV53. How would I disable the internal card and use only my external card?

View 2 Replies View Related

Networking :: Multiple Network Connections - Internal And Wireless

Dec 4, 2008

What I want is quite simple, I have my PC running Linux Mint 5 (Elyssa), and I would like to connect it to both an internal network, which has a file/print server, another machine and will soon host a small cluster. I also have a wireless router connected to the tinterweb.

The thing is using my ethernet I want to connect to the internal network whilst simultaneously using my wireless to deal with the internet, I want to keep the internal network off the net as it really doesn't need to be connected. I can connect to my internal quite happily and also my wireless but not both at once.

View 5 Replies View Related

Networking :: Kernel - Forward Packets From Eth0 To Eth1 And Eth1-to Eth0 As Well As Get A Copy Of These Packets For Analysis

Sep 27, 2010

I have a hardware device with two ethernet ports, eth0 and eth1 running Centos 5. Basically my goal is to forward packets from eth0->eth1 and eth1->eth0 as well as get a copy of these packets for analysis. If I set IP routing to do the forwarding then I won't get a copy of the packets for analysis.

View 3 Replies View Related

Ubuntu :: Control What Buttons/menus Are Listed And Which Icons Are Listed Under Each?

Jul 26, 2010

i just upgraded to ubuntu 10.04 the netbook distro. at the desktop view there is a list of about 10 buttons/menus listed on the left hand side, is there anyway to control what buttons/menus are listed and which icons are listed under each of them? having a netbook i would like to remove and unclutter the desktop view as much as possible but i dont want to remove those apps i still want to be able to open those apps if i want to even if by removing those icons and menus/buttons makes it a pain.

View 1 Replies View Related

OpenSUSE Wireless :: Linksys WPC300N Not Recognized As Eth1?

Mar 13, 2010

I have a Linksys WPC300N v1 "Wireless-N Notebook Adapter" which uses the Broadcom 4329 chipset. Is there a way to troubleshoot and configure this card to use wl, b43, ssb? Preferrably via CLI. I have a couple years of CLI experience in Debian/derivatives (but only in my spare time ).

I have this card recognized and running adequately in Debian (and derivatives) using the 'wl' driver (sometimes supplied by debian.org, other times by broadcom.com). The one hint at a solution for this particular card/chipset I have found searching the OpenSUSE (SuSE for short?) forum points me to using ndiswrapper, which I've never used nor care to if it requires wine. I'm trying to ultimately connect to a b/g/n WPA-1 TKIP wlan.

lspci -v:
03:00.0 Network controller: Broadcom Corporation BCM43XG (rev 01)
Subsystem: Linksys Device 0058
Flags: fast devsel, IRQ 11
Memory at f4000000 (32-bit, non-prefetchable) [disabled] [size=16K]
lsmod | grep 'ssb' returns nothing (neither do 'b43' or 'wl') but 'pcmcia' returns:
pcmcia_core 41748 3 pcmcia,yenta_socket,rsrc_nonstatic

When configuring this card in Debian, I first plugged in the card which resulted in some hard disk activity but the LED was not lit. After installing the driver, the LED came on but no network. After configuring the network, it works 'adequately' (no roaming mode) using the wpa_supplicant package and is readily identified during init.

This is not mission critical by any means so I'm not in a hurry and willing to try almost anything. However, this is an old laptop so I'm even somewhat surprised that KDE4 is running as well as it is (KDE 3.5.10 runs quite well, which is more than I can say for the latest Gnome DE; xfce "screams" relatively). Dell Latitude C-610 PIII-M 1.2 GHz 512 KB cache 512 MB RAM (YaST2 reports this as a C-640 but this does not agree with the BIOS splash). The display is an ATI Radeon LY using the 'radeon' server (default). I don't do compositing here. ;-)

View 9 Replies View Related

Slackware :: Wireless Interface On Eth1 - Setup Config Files?

Aug 23, 2010

All rc.inet1 an rc.wireless scripts work well if a wireless extension is on wlan(x). My notebook has Intel Pro 2100 wireless adapter (the ipw2100 module). By the system the card is marked as eth1. If you have a look at rc.inet1(.conf) you see that by default an eth1 has no wireless extensions. how to set up my network.

View 2 Replies View Related

General :: Wireless Problem On Slackware 13.1 Keeps Switching Back In Forth From Eth0 And Eth1

Jun 23, 2011

I looked at the /etc/rc.d/rc.inet1.conf file it says something completely diff than the iwconfig. iwconfig is saying there is no wireless extensions on lo and eth1 but on eth0 all my info is there now on the conf file it says and ip address on eth2 and nothing on eth 0, or 1. does anybody know why it keeps jumping back and forth? one week its eth0 and maybe 2 months from now its eth1.

View 11 Replies View Related

Ubuntu Networking :: Networking Connections Not Listed In Network Manager

Aug 23, 2010

Neither of my wired network connections are listed in the network manager applet. I know that networking seems to be functional since I can ping local devices on the network. I can't resolve DNS names however. I suppose this is because network manager usually handles DNS? I've posted the outputs of various configurations below.

Code:

/etc/NetworkManager/nm-system-settings.cfg
# This file is installed into /etc/NetworkManager, and is loaded by
# NetworkManager by default. To override, specify: '--config file'
# during NM startup. This can be done by appending to DAEMON_OPTS in

[code]....

View 4 Replies View Related

Ubuntu Networking :: Eth1 On Computer With Only 1 NIC?

Jan 11, 2011

I am running Ubuntu10.04 as a Virtual Machine in virtualbox.I changed my Networking settings from NAT to Bridged Adapter and manually assigned IP addressing information for eth0 in /etc/network/interfaces. For some reason doing /etc/init.d/networking restart didn't bring up the network interface. So i replaced the new /etc/network/interfaces file with the original and rebooted. Now I have eth1 in place of eth0. Under System>Preferences>Network Connections I have Auto Ethernet and eth0. However running ifconfig shows lo and eth1.

View 9 Replies View Related

Ubuntu Networking :: Don't Seem To Have All Variables For Eth1 Inet

Apr 28, 2011

I'm having a strange problem. I'm using Ubuntu server 10.04 LTS and I want to setup a system with 2 network interfaces: eth0 and eth1. However eth1 does not come up at boot I have a screenshot of my /etc/network/interfaces file I don't see what is wrong. eth0 gets it's adress from DHCP eth1 gets a static adress. When i try to restart networking it quits with this message "don't seem to be have all the variables for eth1 inet" Can anyone point out what I'm doing wrong? if i do 'sudo ifconfig eth1 192.168.3.1 netmask 255.255.255.0 up' eth1 comes up

View 3 Replies View Related

Ubuntu Networking :: Eth1 Does Not Start Automatically

May 2, 2011

I have static eth1 defined. When I boot or restart, the networking will not start automatically - i must do it from terminal by ifup eth1.

Where can I put this command to have it autostart?

View 5 Replies View Related

Networking :: 'eth1' Instead Of 'usb0'

Jun 1, 2011

I am working on USB Connectivity between android 2.1 Host and Windows Mobiles 6.1 device...When I connect the windows mobile device to android host through USB (in RNDIS Mode), It is appearing as 'eth1' interface instead of 'usb0' interface. Why 'eth1' instead of 'usb0' ? Does behaviour of 'eth1' is same as 'usb0'?

View 8 Replies View Related

Networking :: Ssh Listening Only To Eth1

Sep 18, 2010

How can I configure ssh to only listen to eth1?

View 4 Replies View Related

Ubuntu Networking :: Change Eth1 Mac Address Permanently 9.10?

Jan 22, 2010

how can I change eth1 mac address permanently in an easy way?

View 1 Replies View Related

Ubuntu Networking :: Stop Internet Access From Eth1?

Aug 24, 2010

I have a bit of a "unique" situation here. I have myself plugged into two networks - since we run two networks here at work (long story, we merged and never combined them due to two different companies) and want to block ALL internet access off eth1, and only have it off eth0. I only want traffic from 192.168.67.1-192.168.67.255 allowed on eth1, but everything allowed on eth0. Or is there a way for the internet/applications to be on eth0 instead of eth1? Would I use iptables or something?

View 4 Replies View Related

Ubuntu Networking :: Sharing The Internet From Eth0 To Eth1?

May 11, 2011

im a linux noob dont get techy ill die of brain fry im running a craft bukkit minecraft server on my 11.04 ubuntu server. however the server uses my only 10m Ethernet cable that i normaly use for my ps3 (i will NOT go wireless. i hate it (or dont like it)) therefor i found an old PCI NIC in an old computer, its a 10/100 realtek one. ifconfig detects it (after two commands:

Code:
ifconfig eth0 up
dhclient eth0
)

now i need to send the internet to my ps3 too.i know the connection wont be blazing fast but isnt it okay?it musnt interrupt the minecraft server. if you need info just ask. ill try and provide them.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved