just installed Ubuntu Netbook Remix on my new HP Mini 210 (info). Everything is working fine -- webcam, shortcut keys etc, but I'm having some difficulties connecting to our wireless network. When I click on the network panel item, there are no networks visible. Now, I also have Windows 7 Starter on the netbook (what I'm using right now) and that's able to connect to the network fine.
View 2 RepliesI successfully did a dual boot on a HP Mini 1001TU netbook. However, the wireless doesn't connect. Over the internet, someone had a similar problem with his Dell notebook using a Karmic and said that Karmic has a bug that doesn't install the "Broadcom STA wireless Driver" and recommended a prerequisite wired internet connection then the following command line:
sudo apt-get update
sudo-get -reinstall install bcmwl-kernel-source
Followed by a reboot which solves the problem.
I would like to try this out but the netbook only accepts a USB -router connection but my router doesn't have a USB port.
I'm using a HP mini netbook, and I recently installed Ubuntu on it. I updated and did the whole proprietary drivers activation and it now scans and sees networks but I am having trouble actually using them now. It says that it is connected to a wireless network but it never loads any pages.
View 7 Replies View RelatedThe Wired Internet adapter isn't working with Ubuntu 10.10, and without this working, I can't get my updates for the Broadcom WLAN adapter. I have a Realtek RTL8101E/8102E PCI-Expredd Fast Ethernet controller. I have looked for solutions, but haven't found any relating to my problem.
To be specific: Ubuntu 10.10 is recognizing the Ethernet adapter as eth0. When I try to manually connect after inserting an Ethernet cable connected to the Internet, it tries for a couple of minutes before telling me the adapter's been disconnected. The connector lights remain the same on the port as they always were.
I decided to try ubuntu on my netbook and it seems to have set up well other than I cannot see any wireless connections. I can't click on connection information. The blue light is on, indicating that my netbook's network card is on.
is there another version that would work better with an hp mini? Otherwise the netbook is rather pointless
I have a dell 1521 and I can't get internet working, I thing the driver is no working with ubuntu 9.10
View 1 Replies View RelatedI loaded Ubuntu on my mini and everything worked fine except it didn't recognize my wireless card in my HP 210 mini.
View 2 Replies View RelatedI've read about all of the problems with the HP Mini's wireless and the Broadcom drivers. Running 10.04 LTS.
Code:
lspci -vnn | grep 14e4
01:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01)
I have 2 drivers available to me under restricted hardware:
Broadcom B43 wireless driver
Broadcom STA wireless driver
I can get the B43 to connect and work, but not for more than a minute or so at a time. I see the following in the kernel log after the wifi adapter is activated:
Code:
May 25 09:16:18 jon-netbook kernel: [ 121.825109] Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
May 25 09:16:18 jon-netbook kernel: [ 121.825125] b43-phy0: Controller RESET (DMA error) ...
May 25 09:16:18 jon-netbook kernel: [ 122.044148] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
May 25 09:16:24 jon-netbook kernel: [ 127.566143] b43-phy0: Controller restarted
May 25 09:16:24 jon-netbook kernel: [ 127.577378] b43-phy0: Controller RESET (DMA error) ...
May 25 09:16:24 jon-netbook kernel: [ 127.796682] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
May 25 09:16:30 jon-netbook kernel: [ 133.333043] b43-phy0: Controller restarted
May 25 09:16:30 jon-netbook kernel: [ 133.333093] b43-phy0: Controller RESET (DMA error) ...
May 25 09:16:30 jon-netbook kernel: [ 133.552336] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
May 25 09:16:35 jon-netbook kernel: [ 139.069058] b43-phy0: Controller restarted
May 25 09:16:35 jon-netbook kernel: [ 139.069078] Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
I installed Ubuntu Netbook on my windows xp machine, a HP Mini 110 with a broadcom wireless card, I installed using Wubi. The wireless on the ubuntu side isn't working and I can't plug into a physical line, how do I fix this?
View 3 Replies View RelatedI want to start off with this: I installed Ubuntu on my HP Mini 1151nr, and it went well. But after installation, the only way I can connect to internet is by directly hooking up to my modem. My wireless is disabled, and I do not think that I have the drivers for it.
The "Additional Drivers" found two Broadcom 802.11b/g drivers, but when I downloaded it came up with errors and didn't work.
I wiped and loaded my mini. ran the ubuntu 10.04.. had to run hardware drivers twice to finally get reference to broadcom and then wireless came on!! Hurray! however (yes, dhcp).. no dns on wireless but on eth0 no problem everything shows up ip, dns.. works fine.. go to wireless it connects, gets ip but in connection information no dns servers listed
View 4 Replies View RelatedI just Installed Ubuntu 10.04 Netbook Edition in my HP MINI 1120 Nr everthing seem to be FINE but WIFI not showing i think the driver is missing.
View 3 Replies View RelatedThe wireless on this computer has worked with Ubuntu just yesterday so I know all the drivers work. The trouble is that now the wireless is turned off and the hardware switch has no effect. Is there a way to force enable it through the terminal?
View 1 Replies View RelatedI have a Samsung N310 with a atheros wireless card. Been having trouble getting it to work. I was thinking about upgrading to a N card anyway so I will be buying one tonight. Does anyone know of a Mini PCI N card that works out of the box with ubuntu 64bit?
View 1 Replies View RelatedI'm a totally rookie at all this. I installed Ubuntu 10.4 Netbook edition in an HP Mini 1116 NR computer--I used an SD card & UNetbootin) and the wireless router is not recognized. I've been pretty much googling and troubleshooting this problem for most of the day. I always get stuck at a dead end. This netbook does not have an ethernet adapter nor a CD-Rom drive, so I have no way of connecting to the internet w/out wireless. I am able to download things from my other laptop to the SD card.
1. When I enter sudo apt-get install build-essential at the terminal, I get "package not found."
2. When I try to install b43-fwcutter or bcmwl-kernel-source, it either won't work because I can't connect to the net or I get a "dkms dependency" issue.
3. So I tried to install the dkms pacakge and got a "gcc dependency" issue. After that, I come up with a dead end.
An alternative option, so I read, is to use ndiswrapper and download the HP wireless broadcom driver, but that driver is a .exe file and I read that ndiswrapper needs a .inf file and I can't seem to find one. Does it matter?
I am not able to connect to a wireless network with the HP mini 110 series. When going to the wireless network menu, no networks shows up. if the solution could be described in a very easy "how-to" or just be made into a patch (if there is pathes on ubuntu) it would be nice.
System specifications from HP:
<li style="font-weight: normal; margin-top: 10px;"> Intel(R) Atom(TM) N455 (1.66GHz) + Intel(R) Graphics Media Accelerator 3150 [For Mobile Broadband] <li style="font-weight: normal; margin-top:
[Code]....
i am new using linux i install fedora 13 in dell mini 10 and i want to how i find and install the drivers for my laptop. I tried Ubuntu the last time and it has some hardware detection but i dont know how it made in fedora
View 5 Replies View RelatedI just installer Ubuntu 10.04 Netbook Remix on my Compaq Mini 700EL, the ubuntu website says that everything works very well including the wireless. But for some reason the list of connection doesn't appear at all. It just says "device not ready" This is driving me a little nuts. It appears that the Broadcom drivers are installed. I typed lspci on the terminal and it says that the computer loads a Broadcom Corporation BCM4312 802.11b/g (rev 01)
I also downloaded the drivers even though they should be already in it. But I'm not sure.
I recently installed Ubuntu Netbook Remix on my Dell Inspiron Mini 10, and for some reason it isn't detecting any wireless networks. The wireless works perfectly fine when I boot to Windows XP on the netbook, but not when I'm using Ubuntu. I tried troubleshooting using this htmlAt the "check for device recognition" step, the terminal tells me that it's disabled, but as far as I can tell there isn't a physical switch that allows me to turn the wireless on or off, and again, it works perfectly fine when I use XP. What should I do?
View 9 Replies View Relatedmay i ask if TP-LINK 150Mbps Mini Wireless N USB Adapter support by Ubuntu? (TL-WN723N) I plan to replaced IBM x60s default wireless adapter, coz it's suffered overheat issued.
View 1 Replies View Relatedmy ubuntu can not detect my wired and wireless mini netbook is HP 100e and impressive is that in any way I can be connected
View 1 Replies View RelatedI'm new to Fedora, I used to have Ubuntu 10 and found that some software I required would not work properly so I decided to Fedora under recommendation from a friend. I really like it but when I installed Fedora 13 on my Netbook I found it difficult to set up my wireless connection.
View 6 Replies View RelatedI have a Dell Inspiron 1525 laptop using Dell Wireless 1395 WLAN Mini-card (This is what Windows Vista says I have). I have installed Ubuntu as dual boot with existing Windows Vista. Wireless is not working in Ubuntu but working flawlessly in Windows.
Here is the output using CODE: lspci.
hai@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
02:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05)
02:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
02:09.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
02:09.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 12)
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
hai@ubuntu:~$
I have an HP mini 110 with Fedora 11 install. I installed the broadcom-wl and wl-kmod from yum but still no wireless. First I can't get the broadcom card to turn on using the slide switch on the front of the computer. The device is inactive in the network configuration-devices window. The card is not in the network configuration hardware window. When I try to add it manually, there is no entry for the card in the drop down list. I am new to Fedora but have used linux for years. Unfortunately this is my first attempt at wireless networking.
The posts and google stuff doesn't say much more than "yum install broadcom-wl" Can anyone point me into the right direction? I have a feeling I am missing something very simple, because this computer dual boots Linux Mint and wireless works flawlessly.
Inspiron 1525 - Wireless 1395 WLAN Mini-Card I passed two days browsing the net looking for a solution to my problem but no way.. Im running ubuntu 10.10 in my inspiron via VirtualBox and my wireless card is not detected by ubuntu.. I installed the bcmwl6.inf driver with the wrapper and it show me in wireless window that the hardware is not present.. So checked that in the terminal by typing :
Code:
lshw -C network
*-network
description: Ethernet interface
product: 82540EM Gigabit Ethernet Controller
[Code].
Installed Ubuntu 9.1 - Linksys WUSB600 connects but no network access. I get "server not found", so no data being xmtted. It worked fine in ver 9.04 but not in 9.1
View 1 Replies View RelatedI recently installed the latest version of Kubuntu in a dual boot system with Windows XP on a Dell laptop. The dell laptop has a broadcom wireless device, and I was able to set up the driver and get wireless working. Then I booted into windows XP to make a whole bunch of updates/driver installations, and when I booted back into Kubuntu it would not connect to the wireless network. I am pretty sure the device is still active, because it picks up on the wireless networks in the area. But KWallet does not open to ask for my password on booting. Something is not set right, but I can't tell what.
View 1 Replies View Relatedin short : installed 9.10 on a dell inspiron 600m which has a broadcom bcm4401 ethernet and an intel PRO/Wireless LAN 2100 3B mini PCI. At this point, i'm not too picky about which one works (meaning neither of them currently work). nm-tool seems to pick up on both : the broadcom (eth0) is using the b44 driver, State is unavailable; the intel (eth1) is using the ipw2100 driver, it's State is disconnected.
i have encryption turned off, and the wireless sees a number of AP's (including mine).
i'm jumping off the good ship m$ and determined to make this work!
My Wireless worked once on Ubuntu but when I disconnected it i got stuck with connection trys that never succeed. On the two little lights only one is green, and when Ubuntu offers to have another try the password is not the same as the one I typed before (and of course is not the good one)
View 2 Replies View RelatedI am new to Linux and just put Ubuntu on my pc when i am using Ubuntu my wireless keeps connecting and disconnecting. Im not sure what I am suppose to do.
My laptop is a Sony Vaio NW130J
The wireless card/driver is Intel WiFi link 5100 AGN
I dont know anything about Linux so if you could please explain it as easy as possible.