Im using natty in lenovo b460. After installation was not able to connect to wifi. Ethernet is working alright. So searched for additional drivers and installed the Broadcom 43xx drivers. After restart the network applet says the wireless is disabled by hardware switch, even after it is switched on/off several times.
After fixing an issue with sleep mode, my WiFi is automatically disabled on my Ubuntu installation on boot while the switch is on. For some reason, it seems that Ubuntu has an issue communicating with my BIOS. As a fix to this problem: I disabled the C4 sleep state. My Ubuntu installation now boots up fine but the LED on the WiFi indicator glows orange, indicating that it's off; while in Windows it glows blue, indicating that it's on.
I was using my usb Alfa AWUS036H-v5 usb wifi card, and then after I rebooted, it randomly stopped working.. did some searching on the site, one idea was to do Code:
sudo lshw -C network
which I did, and it shows my internal wifi card (iwl3945) working fine, but says my wlan7 (Alfa usb) as:
network* Disabled
Also, in the upper right hand corner, the antenna is greyed out and says "Device Not Ready"
having problems with wireless on my old Asus A2500H laptop, NetworkManager applet keeps the "enable wireless" greyed out and gives a "Wireless is disabled" for each wirelss network card. The wireless cards in this laptop are:
Code: 00:0c.0 Network controller: Broadcom Corporation BCM4303 802.11b Wireless LAN Controller (rev 02) 02:00.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) It does look like the network interface come up fine as well: Code: wlan0 IEEE 802.11b ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off
[Code]....
Of course the easy solution would be to just flick that hardware switch on, however there isn't any hardware button only a indicator light, which is off unfortunately.
Any clues to get wifi up? Also tried another pcmcia card but same problem, card is recognized but still "Wireless is disabled".
How does one get the wifi to auto connect upon start up, instead of having to manually select it every time i log on? I think the following script is what i need but im not sure where i would even need to install it.Automatic WLAN Picker Script
I use Network Manager applet to connect to my lan (I don't use dhcp however). The problem is that my machine runs several servers (http, ftp, smb, ...) and should be ALWAYS accessible whenever the computer power is ON, even if there is no user logged. Another problem is that the connection is dropped if you logout and then login with a different user who doesn't know wireless settings (eg my mother, sister, brohter...)
So, is there a way to get a wireless connection at boot time? I mean, using Network Manager. Previously I used wicd or cli tools (iwconfig and wpa_supplicant) but then I switched to NM cause it was more ubuntuish. I'd still prefer not to use wicd, but NM really seems not good software to me
if some options are not really described but i use the german Version. I am new with Ubuntu and Network Manager. Everything ist working fine, but when i start my Netbook i always have to switch on my wifi by my self. Now my question: is there any way to give nm-applet the information with some start option to start with wifi swiched on? Inside the connection Options i already switched on "connect automatically" and "all users can use this connection" also i found the option inside /etc/NetworkManager/nm-system-setings.conf
I loaded Ubuntu 10.10 on a USB stick and when everything is loaded and I try to connect to a network, the notice I get is code...
for my internal wifi adapter and USB adapter. I remember being able to use them in the past with a fresh install of Ubuntu on the same USB stick. What am I missing?
i resently bought HCL ME with windows, i formatted and installed Ubuntu netbook version. i am getting wifi is not connection it looks disabled in network place. my network controller is Realtek semiconductor co., ltd rtl8191sevb rev 10, i am unable to get this driver to install can anyone help me ?
I decided to wing it and upgrade from 10.04 to 10.10 once I developed odd wireless issues (grrr) where I could only get on wireless if I booted up Ubuntu with my wifi switch DISABLED and then right away enabled it once I was logged in. The funny part is, it distinctly said 10.10 available in update manager. I get it done, power up, System - About Ubuntu - 11.04.
I've just finished installing Jessie and everything went well, however when I boot into the installed system the WiFi option says that the hardware is disabled. My laptop is a Lenovo G50 which doesn't have a physical switch. the odd thing is that during installation I'm able to connect to my wifi with no problem!
I am using fc14 i686, and I am having a problem with my wireless card. Even though the led of the wireless card lights up the network manager claims that the wireless is disabled. I don't understand what is going wrong.I am a newbie trying to be sth better bur for the time being my only help could be the outputs of the lshw, lspci and lsusb commands.
I'm trying to configure Linux Mint 9 so that the wireless interface wlan0 is disabled until I enable it. I've hunted around and learned that I can disable the wireless after bootup with the command 'sudo ifconfig wlan0 down' and then restart it with 'sudo ifconfig wlan0 up', but I'd prefer to have it in the 'down' state from bootup. I read up on the /etc/network/interfaces file, and it seemed that the 'auto' stanza was the relevant part that told the system to automatically start the interface, but when I tried commenting out the 'auto wlan0' line wlan0 still started automatically.
Using Squeeze, I wanted to get KMS + DRI2 and suspend/hibernate working with my radeon card using the Open source driver (my card: ATI Radeon Xpress 200M IGP (5955) PCIE (RC410) is no longer supported by the ATI/AMD proprietary driver). I know my card has problems with suspend/hibernate in User modesetting and from what I've read [URL] it has been solved for some only using KMS.
I followed this instructions by the Debian maintainer:[URL] Of course in reality the available version in experimental is now 6.12.191, and mesa 7.7 and libdrm-radeon1 are already in testing. Therefore I only had to get xserver-xorg-video-radeon from experimental and switch KMS on. It worked ok , except that when I tried to hibernate, it didn't even go into hibernate mode!...the screen went blank and the wireless led shut off, but the fan was running and the keyboard lights were on...
Aside from that I also got the following disquieting messages:
[drm:rs400_gart_adjust_size] *ERROR* Forcing to 32M GART size (because of ASIC bug ?) radeon 0000:01:05.0: Wait MC idle timeout before updating MC Failed to wait MC idle while programming pipes. Bad things might happen.
My laptop has an internal wireless device and a button to turn it on/off, but since it has bad reception I use an external USB wireless adapter.The problem is that if I turn the internal wireless device off using the button, it also turns the USB wireless adapter off.Is there anyway to use the killswitch (the button) only for the internal wireless device?This only started to happen in Ubuntu 10.04.
I have only had a few weeks worth of experience with linux, so I'm probably considered a newbie at this but I felt like giving it a shot. I just configured my new Toshiba Satellite A505-S6969 to jaunty. Most of the transition is going well but I'm stuck with a few issues, one of which is getting my wifi to work. Right now I'm working off of an ethernet cable.spci returns
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port
Installed ubuntu 9.10 dual boot with win7 yesterday. Everything working but Wifi. Wifi works fine with Win7. No Wifi in Ubuntu. Very confused. I have info from the wifi trouble ticket post.There does not seem to be a driver for this card anywhere.
lawrence@lawrence-laptop:~$ lspci 00:00.0 Host bridge: Intel Corporation X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13)
get WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0
I have a pc which has 2 network cards, 1 wifi and 1 ethernet card.
I'm using wifi card to connect to wifi network (internet) and i'm planing to share this wifi/internet connection via ethernet to wireless router (siemens sx763) so i can have internet on my other devices, e.g. mobile phone, laptop.
I am running (K)Ubuntu Lucid 10.04 64bit on a Dell Latitude E6400, WiFi Card Intel 5100. Never had any problems with networking. Up to about 2 weeks ago. I do realize there have been quite a few posts with this network adaptor, but non really described the problem I have here.
What happens is that suddenly the WiFi LED on the computer stops blinking, the WiFi connection gets disrupted, and the device is not recognized anymore when checking ifconfig. Only cold restarting the machine helps then... it will work for a while (between 1 and 20 minutes) and then crash again.
On Windows 7 the card works perfectly fine. With Ubuntu 11.04 in Live CD mode I have the same effects (connection crashes after a while). Also tried booting an older kernel, no success.
My exact hardware:
Code:
I notived the following problems in /var/log/kern.log
I have 2 connections, wlan and wired, and I'd want to have a few websites (in my browser) to connect through the wireless connection while other go through the wired rj45 connection. s it possible? (without unplugging the rj45 cable...)
the only error message I can find comes from "dmesg|tail"all it shows is "no IPv6 router"any body know what is going on here or where where to look for more clues the next time I get around public wifi Oh the windoze washers and apple polishers don't seem to have any problems at all
I have an old PowerBook G4 that I would like to use as a 'dummy' computer for learning wireless penetration (WEP/WPA attacks) more effectively. I had been using a wireless router, but I gave it away I can use Mac OS X to share an ethernet connection over wifi, but this is _very_ un-configurable. You get two options only, WEP and a key-length. So, I would like to install someway to make this wireless connection more configurable.
After restart or suspend/resume the Wifi won't start until I click on my home network from the menu. It used to start without me doing anything (once I setup the wireless).
