Ubuntu Networking :: Realtek PCI-E Ethernet Adapter In "deep Sleep"?
Jul 6, 2010
I`ve got a dual boot of win 7 and ubuntu 10.04. After I put the system to sleep in win7, it was unable to start the ethternet adapter back (Now after system boot, the lights around the ethernet port blink for a few times and then turn off. This repeats in a while). Now it is disabled in ubuntu too. Is there any way to start it again? It is a Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller.
View 3 Replies
ADVERTISEMENT
May 1, 2011
I'm experiencing low importance nuisance with conky. I'm running ubuntu 10.10 and use conky to have basic system overview. Whenever I mount/umount USB flash, conky disapears from display. It does not crash, it only falls into neverending sleep (process state: Sl+). When I send rehub signal (kill 1 {conky_pid}) conky happily wake up, reloads configuration and shows me what I want to see. I dont have anything USB realted in my monitor.
View 2 Replies
View Related
Jan 14, 2011
Bus 001 Device 007: ID 0bda:8171 Realtek Semiconductor Corp. RTL8188SU 802.11n WLAN Adapter this adapter shows up in network manager when connected to computer but doesn't detect network and cant connect to any network I have setup in nm, the adapter works fine in windows and it's supposed to work in linux or do I have to install drivers?
View 8 Replies
View Related
Mar 19, 2011
Ubuntu 10.10 - the Maverick Meerkat � (Installed .iso from cd)The router has a password that I'm not sure if is wep or wpa.When I manually put in the address, netmask,gateway, dns,domain my Realtek usb adapter is connecting to the router but is not receiving packets.I got the driver installed with ndiswrapper.I'm trying to figure out wpa_supplicant
View 5 Replies
View Related
Mar 11, 2011
just swapping all my computers over to linux as it far far better than anything i've used before. Have the above driver as identified in lsusb.[URL].. Downloaded the linux driver but dont know what to do from here. Tried doing it the windows inf file way but that didnt work. Or more like i couldnt get it working.
View 9 Replies
View Related
May 17, 2011
my Ethernet card stopped responding a few days after installing Ralink Wireless Card Driver for Linux. I have tried installing the drivers from Realtek's site, but it fails. I also have tried reinstalling the network manager, and that still didn't help any. I have also tried looking online for any post or blog that could help, but that also turned up nothing. The Computer is a new 2010 / 2011 (bought it on new years eve) HP Pavilion desktop that came with windows preinstalled.
View 6 Replies
View Related
Dec 2, 2010
I've got a new laptop with Ubuntu 10.10 (2.6.35-23-generic x86_64 architecture) and with a wireless adapter I can't get to work. The adapter is Realtek RTL8191SEvB:
Code:
$ lspci | grep Network
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10)
[Code].....
View 9 Replies
View Related
May 30, 2011
Today I realized that my newly installed Natty does not recognize the Ethernet port, I used to have it when I was working on the Ubutnu 10.10. The following is the output (only the network related part) of lshw command:
Code:
-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
[code]...
View 5 Replies
View Related
Feb 12, 2011
Just made the jump to Ubuntu, and until this install I considered myself very tech savvy. Now not so much! Built my new desktop, loaded Ubuntu 64 bit no problem. But I'm having a terrible time figuring out how to load the native driver for my realtek wireless adapter. I successfully un-tarred the file, and used the terminal to run the make command by using cd command to navigate to the file. It returned a wall of text, and in my mind looked to work. Next I go to run "./clean" in the same file location in the terminal and it returns:
"ERROR: Module r8192s_usb does not exist in /proc/modules
ERROR: Module ieee80211_rsl does not exist in /proc/modules
ERROR: Module ieee80211_crypt_ccmp does not exist in /proc/modules
ERROR: Module ieee80211_crypt_tkip does not exist in /proc/modules
ERROR: Module ieee80211_crypt_wep does not exist in /proc/modules
ERROR: Module ieee80211_crypt does not exist in /proc/modules
Not completely sure if this is an issue, I try moving to the next step of instructions issuing the command "insmod 8712u.ko" in the terminal same file location and get the error message
insmod: error inserting '8712u.ko': -1 Operation not permitted
I've tried running "sudo insmod 8712u.ko" from both that file directory, and from my home file directory. My guess is I'm missing a step or need to be typing these commands in a different file directory in the terminal.
View 1 Replies
View Related
Jun 22, 2011
(For the record, I have already read the other threads. Either they don't work for me or are too difficult.) My laptop is an Acer TravelMate 250. I have installed Ubuntu 10.10 (2.6.35-28 generic i686) after erasing Windows 7. At first, the usb wireless adapter worked. Then, I restarted the PC because of some updates and it didn't work anymore. In "edit connections" I find "Auto SpeedTouch8350DB" which is the wireless connection (on my sis's computer it works). When it tries to connect, I'm asked the password but it doesn't work.
[Code]...
View 3 Replies
View Related
May 23, 2010
I am using DELL VOSTRO 1510 laptop , it has realtek r8169 ethernet card, i installed RHEL 5 in my laptop , i checked for the driver cd provided by DELL, they given one source rpm and two other rpm for ethernet card, i tried to install them through "rpm -ivh (path)/realtek-r8169 (full name).rpm " but it asking about dependency . i tried it by using yum also but still its not working.
also i tried to create binary rpm through source rpm, but it only generating spec not binary rpm, when i am using " rpmbuilt -ba (spec file) " its showing command not found error. RHEL5 have ethernet driver for realtek-8129 in their list but not for realtek-8169, i checked it in system-config-network window, now what to do, how do i install this rpm , i want to access net through RHEL 5.
View 1 Replies
View Related
May 2, 2011
I've got Fedora 14 (2.6.35.12-90.fc14.i686.PAE) installed and i'm trying to use hostapd with my Realtek RTL8191S USB WLAN Adapter, but can't get it to work. The driver i'm using is : rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 601.tar.gz
[Code]....
View 2 Replies
View Related
Dec 12, 2008
There seems to be some trouble with 8139too not working in a previous post. Has anyone found a solution to this? ubuntu version 2.6.24 (Hardy Heron?). Followed all known possibilities but information is all mostly out of date. module 8139too.ok? does not load. Following makefile on 8139too.c supplied, after altering to suit my version, comes up with 3 pages of errors?. ifconfig shows nothing for eth0like the last person markjuggles i have hit a brick wall here. Am I wasting my time?
View 10 Replies
View Related
Feb 3, 2010
When I first turn it on to the desktop, it automatically connects and disconnects automatically 5 times then sometimes it would disconnect a few times randomly out of the blue.
This ia an external single usb wireless adapter you plug in the usb port on my desktop tower.
View 1 Replies
View Related
Sep 13, 2010
I have Ubuntu 10.04 (32 bits) and a wireless usb adaptor Alfa Network AWUS036H with Chipset Realtek 8187L. After a few minutes connected, the adaptor disconnects and I can't reconnect again. I search this forum but I'm not sure about what to do. Do I need to get and install another driver? I need to use the windows driver?
View 5 Replies
View Related
Mar 5, 2010
I have installed Ubuntu 9.04
uname -r
2.6.28-11-generic
Checked cable/network with 386Box running Ubuntu 8.04 all OK. Could not get Realtek 8168 on mother board to work on Gigabyte H55M-S2H motherboard. I tried to install r8168 driver but no luck ... so I bought another Linux compatible card which turned out to be a RTL8139c (eth1) and the driver I am using on this is card is 8139too.
[Code]....
My preference would be to get the motherboard ethernet working but perhaps the card may be easier to get working. Anyway after searching the net for ideas and trying different things I've just about given up. I have reinstalled Ubuntu today so eth0 is back to using the r8169 driver. I'm no expert so my attempts at following other recipies have so far failed. From what I have read the 8139too driver should have worked with the RTL8139C chip so I have run out of ideas. I must be doing something wrong.
View 9 Replies
View Related
Aug 26, 2010
I've just arrived at uni and to set up my wifi apparently I need my "media access control which is listed as the phsyical address for ethernet adaptor local area connection." on windows you can find it by using the command ipconfig /all but that didn't work when i put it into terminal.
View 1 Replies
View Related
Dec 26, 2010
just recently I made the move back to Ubuntu from Windows. Upon re-installing I noticed a problem with me connecting to the internet. Previously on Windows I had updated my Ethernet Adapter driver, upon installing I would have to disable and re-enable the device to let my computer have access to the internet. My problem here is how would I go about fixing this on Ubuntu so I can have internet access on Ubuntu
View 1 Replies
View Related
Jan 17, 2011
The Wired Internet adapter isn't working with Ubuntu 10.10, and without this working, I can't get my updates for the Broadcom WLAN adapter. I have a Realtek RTL8101E/8102E PCI-Expredd Fast Ethernet controller. I have looked for solutions, but haven't found any relating to my problem.
To be specific: Ubuntu 10.10 is recognizing the Ethernet adapter as eth0. When I try to manually connect after inserting an Ethernet cable connected to the Internet, it tries for a couple of minutes before telling me the adapter's been disconnected. The connector lights remain the same on the port as they always were.
View 1 Replies
View Related
Feb 12, 2011
I have this tread, for a ASIX USB ethernet adapter. Still don't work.Tody i bought a Davicom DM9601 USB 10/100 EthernetI read here about this work out of the box, since 2.6.21 kernel. I have Linux Mint (Ubuntu 10.10) with 2.6.35-x kernol version; lsusb detect it; dmesg, detect it; at configure, automaticly get the MAC address, but just didn't work; with ping command, i get network is unreachable.
View 1 Replies
View Related
Apr 14, 2010
I am trying to setup a VPN using OpenVPN to allow a secure connection between my smartphone and my LAN. I have been reading an OpenVPN book and some tutorials on how to setup the server side, but I'm stuck at how to create a virtual device. The OpenVPN book says when installing OpenVPN the installer (or aptitude to be more precise) should ask me if it should create a TAP/TUN device. The thing is, it doesn't ask me anything at all. It just installs, that's it.
Most tutorials simply tell me to create a new device in the network/interfaces file. Where is the difference? What should I do now? I like having options, that is one reason I like Linux, but this does confuse me. My second question is about the IP range of the virtual adapter. Should it be in the same range as my LAN, or should I use something entirely different?
View 1 Replies
View Related
May 20, 2010
I have two pci network adapters. I see them in pci device list (lspci). And I see them using ifconfig. How do I relate them - which pci device corresponds to ifconfig network adapter ? (I can't open my hardware and relate them using MAC stickers)
View 4 Replies
View Related
May 25, 2010
I have just completed installing Ubuntu 10.04 LTS. When I click on teh network manager it shows:
Wired Network
disconnected
Wireless Network (Intel PRO/Wireless 2200BG [Calexico2])
wireless is disabled
Wireless Network (Manufacturer RealTek RTL8187 RTL8187 Wireless)
[Code]....
I want to be able to connect through the RealTek wireless adapted.
View 3 Replies
View Related
Jan 30, 2010
Out of all the Linux I have tried, this is the only one which will hibernate and startup again properly. But it has no drivers for the rtl2860 wifi adapter. I am thinking of using NDIS wrapper, but it may stop hibernation working. I see a guide which I am going to try to follow, but has anyone out there got this adapter working and hibernation still works?
View 2 Replies
View Related
Jun 17, 2011
So I bought a new wireless pci-e adapter today that has a realtek 8192CE chipset. I checked before I bought it and it is supported in the kernel since 2.6.38. Just to be safe I used the kernel-huge-2.6.39-rc4 config file from testing just to get it to work. All the kernel modules are loaded correctly and it is recognized by iwconfig, however wicd acts as if there is no wireless card in the system. I checked dmesg and saw this error.
rtl8192cu:loading firmware file rtlwifi/rtl8192cfw.bin
rtl8192cu:firmware loading failed
So I googled around and didn't find much except for somethings about needing firmware. I did make firmware_install but for some reason there is no rtlwifi/rtl8192cfw.bin file. As a test I found an RPM that had the bin file I needed. I converted it to a tgz and ran explodepkg on it to extract the one file I needed. I made a directory /lib/firmware/rtlwifi and dropped the .bin file in and wicd immediately found my networks. So I guess it is a missing firmware issue, however I am currently not able to obtain and ip address. Why did the kernel not build the firmware I need, or is that something I have to download and build separately?
View 3 Replies
View Related
Nov 22, 2010
I have a situation when vsftpd do not allow to get files from directories deeper than chrooted directory.
I can get from chrooted directory.
I can put to chrooted directory.
I can put to deeper than crooted directory.
I can list directories and files deeper than chrooted direcotry.
But I can not get files (process starts and hangs) from directories deeper than chrooted.
Firewalls on both sides (client and server) are set to log every in and out connection that do not -j ACCEPT. Log files are empty, so I assume nothing is blocked by firewalls.
Permissions for files and directories, I want to get, are set to 777.
View 1 Replies
View Related
Jul 14, 2011
I'm going to start using Debian as my desktop system rather than Ubuntu since I'm not really liking all the crazy eye candy and just wanted a fast and simple system. My main problem is networking, I guess I'll start off with my system specs and other information for problem solving.
My specs are:
- Intel Core i7 2600K CPU
- Gigabyte Z68X-UD3P-B3 Motherboard
- 8GB DDR3 1600Mhz RAM
I have a Realtek RTL8111/8168B Ethernet Adapter builtin to my motherboad which I am using, I could only get a basic connection, by basic I mean that it allowed me to connect to my local area network but not the internet. I then modified /etc/NetworkManager/NetworkManager.conf to change to managed=true this allowed me to use the internet, but the problem is, that it is a very unstable connection, the speed is very slow and it drops a lot! I have to carry on running /etc/init.d/network-manager restart twice to get my connection back, which lasts for about a minute.
output of lspci | grep -i eth
07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
Output of cat /var/log/dmesg | grep -i eth
[ 1.414250] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.415080] eth0: RTL8168b/8111b at 0xffffc90000c7c000, 1c:6f:65:c5:7c:34, XID 0c900800 IRQ 31
[ 9.213351] r8169: eth0: link up
[ 9.213392] r8169: eth0: link up
[ 13.813496] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
View 1 Replies
View Related
Mar 26, 2011
This is the wireless card that came with my Toshiba Satellite L655D-S5093. First check to see if you have the correct driver. Run
[Code]....
View 3 Replies
View Related
Feb 9, 2010
How to install Realtek 8139 Ethernet driver? I tried downloading from realtek website. there is no driver for Realtek 8139. Although i downloaded the driver for 8168 for Linux, i could not install it after uncompressing the tar file
View 1 Replies
View Related
Oct 17, 2010
After updating to openSUSE 11.3, and restarting my computer, I placed my computer in sleep(suspend to RAM) mode, and I lost my internet connectivity. I noticed that my computer was only connected through ethernet. After entering "dhclient eth0" in a terminal, I received the following output.
Code:
RTNETLINK answers: Cannot allocate memory
This is the first time that I have had issues with connecting to the Internet using Ethernet.
View 6 Replies
View Related
