Out of all the Linux I have tried, this is the only one which will hibernate and startup again properly. But it has no drivers for the rtl2860 wifi adapter. I am thinking of using NDIS wrapper, but it may stop hibernation working. I see a guide which I am going to try to follow, but has anyone out there got this adapter working and hibernation still works?
View 2 RepliesThis is the wireless card that came with my Toshiba Satellite L655D-S5093. First check to see if you have the correct driver. Run
[Code]....
I've got Fedora 14 (2.6.35.12-90.fc14.i686.PAE) installed and i'm trying to use hostapd with my Realtek RTL8191S USB WLAN Adapter, but can't get it to work. The driver i'm using is : rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 601.tar.gz
[Code]....
I am trying to install Realtek RTL8192E wireless drivers for Toshiba satellite 510 in Fedora 14 KDE SPIN. I have been searching it for long time. I am not getting any tutorials or any methids to get this sorted.
View 1 Replies View RelatedMy laptop has an internal wifi adapter, but I recently purchased another one because of its extended range.susb, shows that the new adapter is:
Code:
Bus 002 Device 027: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
After disconnecting my internal adapter from the wireless network, I can scan for networks
[code]...
After a new fresh-from-DVD install of Fedora 14 64-bit (over top of Fedora 12 64-bit which went over top of Fedora 10 64-bit before that) my Linksys WUSB600N adapter connects at login to my WiFi N router with WPA2 Personal.
That is great, as previously (fc10/12) I had to use the Ralink drivers per ogetbilo's thread on this forum (that thread kept me on the net for many years now). And at some point this even became a pain because sometimes the system would boot and refuse to connect to the wireless (which would hang trying to connect) and then crash to a dump screen on shutdown (bug reported). The fix was hoped to be found in upgrading to F14 and the newer kernels with working native Ralink chip support.
But I still have an issue... the connection stays up for a few minutes then drops. If I disable/re-enable wireless it (at least sometimes) re-connects. But obviously that is not workable. This is a USB adapter and I am not entirely sure that there is not some USB powersave issue going on, but I do not see anywhere to disable system USB power saving either.
im using fedora 10 with gnome on a laptop, i want to increase power to my wifi adapter as im only getting 40% connection strength to the nearest wifi AP (about 20 feet) in windows under power management there is a slider with best performance against battery life, is there a similar setup in fedora 10? ps, if explained fairly well, i dont mind shell scripting (bash) and compiling.
View 2 Replies View RelatedI am looking for a powerful (500mw+) wifi USB adapter for my netbook, and after spending quite a bit of time on Amazon, Newegg and Google I couldn't find anything that would work properly on Fedora without compiling the drivers and stuff. Some are reported to work on Debian distros, but couldn't find any reliable reports of them working on Fedora.
View 2 Replies View RelatedBus 001 Device 007: ID 0bda:8171 Realtek Semiconductor Corp. RTL8188SU 802.11n WLAN Adapter this adapter shows up in network manager when connected to computer but doesn't detect network and cant connect to any network I have setup in nm, the adapter works fine in windows and it's supposed to work in linux or do I have to install drivers?
View 8 Replies View RelatedUbuntu 10.10 - the Maverick Meerkat � (Installed .iso from cd)The router has a password that I'm not sure if is wep or wpa.When I manually put in the address, netmask,gateway, dns,domain my Realtek usb adapter is connecting to the router but is not receiving packets.I got the driver installed with ndiswrapper.I'm trying to figure out wpa_supplicant
View 5 Replies View Relatedjust swapping all my computers over to linux as it far far better than anything i've used before. Have the above driver as identified in lsusb.[URL].. Downloaded the linux driver but dont know what to do from here. Tried doing it the windows inf file way but that didnt work. Or more like i couldnt get it working.
View 9 Replies View RelatedSo I bought a new wireless pci-e adapter today that has a realtek 8192CE chipset. I checked before I bought it and it is supported in the kernel since 2.6.38. Just to be safe I used the kernel-huge-2.6.39-rc4 config file from testing just to get it to work. All the kernel modules are loaded correctly and it is recognized by iwconfig, however wicd acts as if there is no wireless card in the system. I checked dmesg and saw this error.
rtl8192cu:loading firmware file rtlwifi/rtl8192cfw.bin
rtl8192cu:firmware loading failed
So I googled around and didn't find much except for somethings about needing firmware. I did make firmware_install but for some reason there is no rtlwifi/rtl8192cfw.bin file. As a test I found an RPM that had the bin file I needed. I converted it to a tgz and ran explodepkg on it to extract the one file I needed. I made a directory /lib/firmware/rtlwifi and dropped the .bin file in and wicd immediately found my networks. So I guess it is a missing firmware issue, however I am currently not able to obtain and ip address. Why did the kernel not build the firmware I need, or is that something I have to download and build separately?
I've got a new laptop with Ubuntu 10.10 (2.6.35-23-generic x86_64 architecture) and with a wireless adapter I can't get to work. The adapter is Realtek RTL8191SEvB:
Code:
$ lspci | grep Network
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10)
[Code].....
my long awaited WUA-1340 D-Link wifi adapter has arrived, and...unfortunately won't work it didn't work "out of the box", so I tried the following (found on the aircrack website)Here's what I did....1. Edit /etc/modprobe.d/blacklist and add blacklist rt73usb as a new line.2. RebootThen,
Code:
wget http://homepages.tu-darmstadt.de/~p_larbig/wlan/rt73-k2wrlz-3.0.3.tar.bz2
tar -xjf rt73-k2wrlz-3.0.3.tar.bz2
[code]....
I'm going to start using Debian as my desktop system rather than Ubuntu since I'm not really liking all the crazy eye candy and just wanted a fast and simple system. My main problem is networking, I guess I'll start off with my system specs and other information for problem solving.
My specs are:
- Intel Core i7 2600K CPU
- Gigabyte Z68X-UD3P-B3 Motherboard
- 8GB DDR3 1600Mhz RAM
I have a Realtek RTL8111/8168B Ethernet Adapter builtin to my motherboad which I am using, I could only get a basic connection, by basic I mean that it allowed me to connect to my local area network but not the internet. I then modified /etc/NetworkManager/NetworkManager.conf to change to managed=true this allowed me to use the internet, but the problem is, that it is a very unstable connection, the speed is very slow and it drops a lot! I have to carry on running /etc/init.d/network-manager restart twice to get my connection back, which lasts for about a minute.
output of lspci | grep -i eth
07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
Output of cat /var/log/dmesg | grep -i eth
[ 1.414250] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.415080] eth0: RTL8168b/8111b at 0xffffc90000c7c000, 1c:6f:65:c5:7c:34, XID 0c900800 IRQ 31
[ 9.213351] r8169: eth0: link up
[ 9.213392] r8169: eth0: link up
[ 13.813496] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Just made the jump to Ubuntu, and until this install I considered myself very tech savvy. Now not so much! Built my new desktop, loaded Ubuntu 64 bit no problem. But I'm having a terrible time figuring out how to load the native driver for my realtek wireless adapter. I successfully un-tarred the file, and used the terminal to run the make command by using cd command to navigate to the file. It returned a wall of text, and in my mind looked to work. Next I go to run "./clean" in the same file location in the terminal and it returns:
"ERROR: Module r8192s_usb does not exist in /proc/modules
ERROR: Module ieee80211_rsl does not exist in /proc/modules
ERROR: Module ieee80211_crypt_ccmp does not exist in /proc/modules
ERROR: Module ieee80211_crypt_tkip does not exist in /proc/modules
ERROR: Module ieee80211_crypt_wep does not exist in /proc/modules
ERROR: Module ieee80211_crypt does not exist in /proc/modules
Not completely sure if this is an issue, I try moving to the next step of instructions issuing the command "insmod 8712u.ko" in the terminal same file location and get the error message
insmod: error inserting '8712u.ko': -1 Operation not permitted
I've tried running "sudo insmod 8712u.ko" from both that file directory, and from my home file directory. My guess is I'm missing a step or need to be typing these commands in a different file directory in the terminal.
(For the record, I have already read the other threads. Either they don't work for me or are too difficult.) My laptop is an Acer TravelMate 250. I have installed Ubuntu 10.10 (2.6.35-28 generic i686) after erasing Windows 7. At first, the usb wireless adapter worked. Then, I restarted the PC because of some updates and it didn't work anymore. In "edit connections" I find "Auto SpeedTouch8350DB" which is the wireless connection (on my sis's computer it works). When it tries to connect, I'm asked the password but it doesn't work.
[Code]...
I have a logitech c310 webcam. When I open cheese, I get a blank. Also my wifi adapter stops working - it doesn't show up on lsusb anymore. How do I fix this? How do I get both my wifi adapter and camera to work at the same time and how do I get my webcam to work? The adapter is D-Link DWA-125. Here are the outputs for lsusb:
[Code]...
When I first turn it on to the desktop, it automatically connects and disconnects automatically 5 times then sometimes it would disconnect a few times randomly out of the blue.
This ia an external single usb wireless adapter you plug in the usb port on my desktop tower.
I have Ubuntu 10.04 (32 bits) and a wireless usb adaptor Alfa Network AWUS036H with Chipset Realtek 8187L. After a few minutes connected, the adaptor disconnects and I can't reconnect again. I search this forum but I'm not sure about what to do. Do I need to get and install another driver? I need to use the windows driver?
View 5 Replies View RelatedAlright so I have been having issues with my Wifi, large packet loss, pages take forever to load. here is the cards info if you need any other info let me know. Been googling it and trying things since yesterday with no success Network controller: Realtek Semiconductor Co., Ltd. RTL8188EE Wireless Network Adapter (rev 01)
View 6 Replies View RelatedI have used google and read a few topics here at this forum. ( especially this Getting Your Wireless to Work was very interesting for me ) But it is useless for me, because I am newborn in GNU/Linux. I use openSUSE 11.3 with KDE. I have read, that you need some informations about my hw. I hope these are
uname -r
2.6.34-12-desktop
lspci
0e:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10)
hwinfo --pci
31: PCI e00.0: 0280 Network controller
[Code]...
I have downloaded the driver installed it, and it works fine. But i can't get to turn it off. I do have the ability to unload the driver's kernel modules and the sysyem does not see my card after that. That's ok, but i'm thinking it still uses my battery power. The wifi led is always on no matter what i do. The fn+<wifi key> doesn't to anything.
View 8 Replies View Relatedanyone tried to run wifi-card based on this chip? In coming days I will build myself a proprietary driver for 2.6.27.7 kernel. I mostly aware about patches for wpa_supplicant. Should I use a source for wpa_supplicant from slackware 12.2 distro or a new version? Do you know about any other prerequisities (requirements, dependencies) for building this proprietary driver?
View 2 Replies View RelatedI just installed SUSE 11.4. In short - my adapter is working, authenticated on the selected AP, I can ping the AP, but I have no access to the outside world. Here's the command line output:
xaoc@FOREST:~> dmesg ...
[795.517345] wlan0: authenticate with 00:01:38:e2:39:8c (try 1)
[795.533595] wlan0: authenticated
[795.638329] wlan0: associate with 00:01:38:e2:39:8c (try 1)
[795.640960] wlan0: RX AssocResp from 00:01:38:e2:39:8c (capab=0x431 status=0 aid=3)
[795.640964] wlan0: associated .....
--- 192.168.1.1 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4004ms
rtt min/avg/max/mdev = 2.118/5.169/16.063/5.454 ms
xaoc@FOREST:~> ping -c 5 66.70.73.150
connect: Network is unreachable
i tried following the readme file included in the driver of the usb network adapter but seems its not exact.
any ideas on how i can configure it manually? KDE does not detect any wifi device. .(of course since no driver is installed yet).
i used my desktop (win***)with DSL connection and installed the driver of the usb net adapter.. made it as the access point. . so my laptop detects the desktop as wifi spot.
I am having issues with wifi on my Lenovo X220. What has occurred is that the network applet in the notification bar no longer shows me any wireless network options. When I click on the applet, the drop down shows me: Wired network: disconnected (greyed out), VPN connections, Enable networking (checked), Connection information (greyed out), and Edit connections. Missing is Wireless connections. This occurred "out of the blue" in the middle of using the computer (i.e. NOT just after a reboot or new driver installation, etc.)
I have noted that:
1. Wired ethernet works just fine.
2. Wireless (wifi) works when I boot into Windows 7 or into a fresh Ubuntu USB Start up disk (implying that this is a software issue, not hardware).
3. The hardware led for wifi is OFF (whereas the Bluetooth light is on.) In Windows or using a fresh ubuntu from USB, this light turns on normally.
This may be irrelevant, but the issue started yesterday when I noticed that the trackpoint scrolling that I had enabled using gpointing-device-settings was not working. I ran that app and checked the settings, which were normal. I then reset the computer, and found the trackpoint was working just fine, but I had no wifi. A few resets later, the problem was not solved.
[Code]...
I`ve got a dual boot of win 7 and ubuntu 10.04. After I put the system to sleep in win7, it was unable to start the ethternet adapter back (Now after system boot, the lights around the ethernet port blink for a few times and then turn off. This repeats in a while). Now it is disabled in ubuntu too. Is there any way to start it again? It is a Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller.
View 3 Replies View RelatedI have just completed installing Ubuntu 10.04 LTS. When I click on teh network manager it shows:
Wired Network
disconnected
Wireless Network (Intel PRO/Wireless 2200BG [Calexico2])
wireless is disabled
Wireless Network (Manufacturer RealTek RTL8187 RTL8187 Wireless)
[Code]....
I want to be able to connect through the RealTek wireless adapted.
I am currently running openSUSE 11.4 on my Toshiba A505 laptop. I'm not certain about the exact model number of the wireless adapter but I believe it's made by Realtek. It does not show up in my list of network connections in YaST so I assume I'll need a driver for it.
View 7 Replies View Related