Ubuntu Networking :: How To Setup Wireless Connection
Jan 13, 2010I need to setting up my wireless connection on ubuntu.
View 1 RepliesI need to setting up my wireless connection on ubuntu.
View 1 RepliesMy adsl modem is in bridge mode. I can connect to internet via pppoe . pppoeconf recognise the pppoe in eth0 and setup a connection and I can use it. How can I setup a pppoe connection using pppoeconf so that it uses wireless ? I set the wireless mode to bridge in modem settings. But, after that the access point stopped appearing in "aps in range" in network manager and I can't connect to it. pppoeconf also doesn't recognise wlan0 as a valid pppoe link . but dat is normal since i don't think it can check if wlan0 is pppoe without wlan0 being connected to the modem's wireless network. How can I connect to Internet with modem in bridge mode and connections via wireless interface of modem? Is pppoe over wireless even possible ? coz the datalink layer of wlan is not ethernet rite?
View 6 Replies View RelatedI tried setting up a adhoc wifi in my debian laptop, so that my other laptop running Ubuntu could connect to it. Though the access point made on Debian laptop is visible on Ubuntu laptop, I could not establish a connection.Then I used create new wireless network tab to create a connection named test1. Though it shows up on Ubuntu box, i couldnt connect to it.
View 4 Replies View RelatedI have a computer with both wire and wireless connections. Wired connection works fine, but I would also setup the wireless connection.(I also have a dual boot on this cumputer with WinXP where both wire and wireless connections works fine. So, wire and wireless configuration of the actual router is not an issue here.)
At this point I just want to know the main/overview basic steps of setting-up the wireless connection on the computer. Also if you could suggest any links to guidelines for these steps. I have been thinking about something simple like this, but I might have missed a lotInvestigate if Ubuntu finds the wifi-hardware - the installed wifi card.Investigate if Ubuntu have an installed driver for this wifi-card.Configure the Wireless Network connection, like SSID.Unplug wire connection and reboot.
I am trying to setup a wireless connection between F10 and a HP J6480. I dnloaded the linux driver hplip-3.9.2, disabled the SELinux and ran the install. When I choose method of connecting - wireless it would not discover the device. The only way was to enable the USB descovery. Doing so, the computer found the printer and all is fine. What am I missing trying to enable the wireless connection. Note, that during this process, the USB was not connected. Also, I dual boot with Vista and I can run the printer wireless.
View 7 Replies View RelatedI'm trying to set up a wireless or wired network (wireless would be better...) to share my connection with my housemate, as well as with some devices. The only guide I found regarding this (I must admit, I didn't have much time to put into research), was dating back to 2005, and although doable, seemed somewhat confusing. Getting to the point: is there a way (maybe a standalone program, or some kind of plugin) to share a connection?
View 9 Replies View RelatedI'm trying to set up a wireless connection to my personal wireless net. I have a Linksys N router and I am using a WMN 300n adapter. I found out how to get the connection manager but I'm not sure if i ams upposed to enter the MAC of the router and I know what the SSID is but the B**ssid(not quite sure what that was and I'm on a Win7 system right now)so any info to get my wireless connection now
View 5 Replies View RelatedI have recently installed Ubuntu 8.04 LTS Server Edition, with no GUI. I can't connect to internet, and therefore I can't use commands like "apt-get update" I do not even know how to configure this server yet. I need my server to connect to Internet through my wireless card (I have no cable connexion for now).
View 4 Replies View RelatedI'm trying to setup PPPoE connection to establish my DSL connection, but I got
Code:
pppoe[3885]: read (asyncReadFromPPP): Session 4479: Input/output error
pppd[4104]: Cannot determine ethernet address for proxy ARP
in my sylog file.
When I do pppoe-start, it connected but I cannot ping into any destination (even to my modem in the same network). DNS servers are explicitly set in pppoe.conf and resolv.conf. Did I miss anything?
am finding it very hard to get a wireless connection working, I am using openSUSE 10.3 (i586)and I have a Edimax EW-7711UTn USB adaptor, I have tried to follow the instructions on this forum and I think I have set it up using YaST2 but I still can not connect to the internet.
View 6 Replies View RelatedA friend who switched ISP's gave me his old Linksys WRT54-G wireless router. I went through the installation procedure and had a wireless connection up and running - smiley face. I had security set up for WPA, and decided to upgrade it to WPA2. Another smiley face. When I went to connect (had already done so successfully), I noticed it referred to my wireless as Linksys - I was expecting to see the SSID. So I started playing around in Network Manager and now I have things all effed up.
Don't know exactly what I did, but now I have no wireless. So I ran a few commands (lshw -C network, iwconfig, ifconfig, and iwlist scan), and looking at the results I see what appear to be inconsistencies in the output. I've posted them below, and make the following observations:
1. Under the lshw it refers to my wireless connection logical name as wmaster0, and has the correct MAC address, etc.
2. Under the iwconfig it says, 'wmaster0 no wireless extensions', but then refers to wlan0 as the wireless connection (although it does not seem to be running).
3. Under ifconfig I see both a wlan0 and a wlan0:avahi. The wlan0 has no IP, the wlan0:avahi does, but it is incorrect.
[Code]...
I have just done a new install of the latest opensuse 32bit and for some reason I cannot connect to the internet, when I click on mange connections the vpn tag is highlighted and all the other tabs are grayed out and I cannot select them. So I can't setup a internet connection wired or wireless. I was just using Kubuntu and did not have this problem. My card is broadcom.
View 9 Replies View RelatedIts a case of ".... wireless network connection active but still not internet connection .."I am using WEP - 128 key ... Works when I connect directly using ethernet cable ... but not wireless (pci and wireless router)
ubuadmin@ubucomputer:~$ ifconfig
wlan0 Link encap:Ethernet HWaddr 00:06:25:12:83:3b
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::206:25ff:fe12:833b/64 Scope:Link[code].....
My problem is exactly the same as [URL]
but I am stuck at the last hurdle
here are the output of the command that helped to solve the case in the previous post:
ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 00:1b:77:d2:59:55
inet6 addr: fe80::21b:77ff:fed2:5955/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[Code].....
I have also tried sudo dhclient but it hasn't helped and I am still unable to connect to the internet
I have installed Fedora 11 recently. I want to share my Internet connection.
I have e LAN connection eth0 which is connected to internet.
I have a Wireless connection wlan0.
I want to share my internet connection with wireless connection.
I have two linux laptops. Currently, I'm using both of them at work, side-by-side. Now the problem is, I'm connected to a wireless router, but the wireless only works on one of the laptops. So I'm stuck with one laptop that has no access to the internet. Both machines do, however, have working ethernet nic cards. So, I was wondering if I could use the laptop with the wireless connection to share the internet connection with my other linux machine and access the internet on both of them. Or as an alternative, just use the internet on the machine without wireless and be able to switch back and forth, that would increase my productivity like 30 fold.
View 5 Replies View RelatedI've just done a fresh install of Ubuntu 10.04 lucid lynx and how to setup a pppoe connection in ubuntu. ( thats after 2 hours of googling and trial and error)
system info: its a laptop : Dell Studio XPS 16 connected to a Ethernet hub thats connected to a dsl modem..
I recently setup ubuntu 9.10 in my desktop..I don't know whether the connection is dialup or not. I used the connection with cable connection. I have got the following information from my ISP:
User name: n372_asad_go@brisksys.net
service name: brisknb
password: 16251521
I have backtrack 4 os on my acer netbook and i want to create a vpn connection! how to setup the vpn connection?
View 1 Replies View RelatedI have BIG troubles trying to set up wired internet connection in Ubuntu! To be able to connect to the internet I have to enter my MAC address, 2 IPs, netmask and 2 DNS address. When I try to edit the default internet connection eth0 with my correct information, the minute I enter my MAC address and save the changes the network manager creates new internet connection with wrong data and use it instead! I can't select the correct internet connection from the top bar where the internet icon is, because it is just not there. The only connection that I can choice is the new default one with the wrong data! If I try to create new separate internet connection with my correct data the same thing happens! The moment I enter my MAC address and save it, the internet connection disapears from the list of internet connections in the internet area in the top bar and I can't select it. I tried googling it, but with no luck I think that if I set up my connection trough the terminal everything will be ok
View 2 Replies View RelatedI am running FC13 on a Compaq Presario 2100 using a Broadcom BCM4306. I was able to get it running thanks to Fedora Unity Project. But It's a very unstable connection. I don't know what settings to adjust or enable or disable. It's not my router, this is the only wireless connection in the house that I have trouble with.
View 1 Replies View RelatedHow can I setup a lan connection using wireless pci card on entire system D-link DWA-510 card I have .
View 5 Replies View RelatedI have a similar problem. My ubuntu box is set up as a dhcp router for my Xbox360, my xbox can get ip and DNS information from the computer, but it doesn't seem to get the right info. The ip address it gets assigned is out of the range I've set in etc/dhcp3/dhcpd.conf.
View 1 Replies View RelatedI have a 2G Broadband service through my Ethernet cable. My provider in China has a user name and password to login to their service. I don?t have a modem or anything but the wire coming in from the outside. It is setup in windows but I can?t figure out how to do it in Ubuntu 11.04.
View 1 Replies View Relatedi am accesing internet via proxy server till now...now i switched from proxy server to broadband connection. can't able to setup internet connection.
View 2 Replies View RelatedI installed the Kde desktop and i'm unable to setup a broadband dsl connection
i have done the settngs in network manager gave password username service name etc.
but the option for connection doesnt appear
the connection works properly in windows as well as gnome 3 desktop but not in kde
i am not able to set up a crossover connection between 2 CENTOS 5.5 boxes.
View 4 Replies View RelatedI want to settup a proxy server who just redirect the internet connection to my second computer. I try Squid Proxy but its too complicated for me. Can you sugest me another more simple program to do what i want?
View 1 Replies View RelatedI'm using Ubuntu 9.04...How do i setup a broadband connection that DOES NOT require a username and password i tried pppoeconf but it wont let me proceed without entering something in the username and password fields. on XP i jus plug in my Ethernet cable and it works but it doest on ubuntu.
View 9 Replies View RelatedI'm still fairly new to Linux so please forgive me if my description of my problem leaves out important information. My problem is centered around using a AT91SAM9G45 development board (DB)on Fedora 10. I have directions on how to setup on my host machine a DHCP server to connect to the development board. I have installed an additional network card (eth1) that will be used exclusively to communicate with my DB.
The DB has been setup with an ethaddr=12:34:56:78:9a:bc and an ipaddr=192.168.251.191.
The following is info from ifconfig for eth1:
eth1 Link encap:Ethernet HWaddr 00:0A:5E:1A:46:1C
inet addr:192.168.251.190 Bcast:192.168.251.255 Mask:255.255.255.0
inet6 addr: fe80::20a:5eff:fe1a:461c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:38 errors:0 dropped:0 overruns:0 frame:0
[Code]...