am finding it very hard to get a wireless connection working, I am using openSUSE 10.3 (i586)and I have a Edimax EW-7711UTn USB adaptor, I have tried to follow the instructions on this forum and I think I have set it up using YaST2 but I still can not connect to the internet.
View 6 Replies
opensuse 11.3 cannot detect my wirless card.
View 9 Replies View RelatedHave an issue with my wireless.It sometimes doesn't connect to my wireless. And sometimes when it does it gives me an invalid IP address.I have a lenovo SL400 Laptop.Intel 802.11agn wireless is my adaptor. And I have OpenSuse 11.4 with gnome. I works fine if I give it a static IP Address but that will create an issue with other computers on the network.Is my desktop environment (GNOME) or is my Wireless adpator not compatible with opensuse.
View 9 Replies View RelatedI have just done a new install of the latest opensuse 32bit and for some reason I cannot connect to the internet, when I click on mange connections the vpn tag is highlighted and all the other tabs are grayed out and I cannot select them. So I can't setup a internet connection wired or wireless. I was just using Kubuntu and did not have this problem. My card is broadcom.
View 9 Replies View RelatedFor upgrade-check I used today Ubuntu 11.04 X64 LiveCD om my Sony Viao VPCF13Z1E Laptop to check if all my hardware can be used with Ubuntu 11.04. When Ubuntu 11.04 X64 LiveCD was started I could connect to my network with my wireless network adapter. But when I tried to browse with Firefox I could not get a connection. A ping to my router or to an other machine did neither work. To browse the internet with Firefox and a wired connection works normally. When I use Ubuntu 10.10 X64 on my laptop the wirelss connection works normally.
The command lspci | grep -ni network on my Sony laptop responds with: 23:02:00.0 Network controller: Intel Corporation Centrino Advanced-N 6200 (rev 35) I use a wireless connection based on wpa/wpa2
Connection information from Ubuntu 10.10 X64:
Interface 802.11 WiFi (wlan0)
Driver iwlagn
Does anyone have an idea how to solve this problem? Or do I have to report a bug?
Ever since my BT Hub 2 has updated a few weeks ago I'm unable to connect to the internet either wireless or wired. I duel boot on my netbook with xp and duel boot my desktop PC with windows 7. None of the Ubuntu�s are able to connect, I have no problems with the windows side of things.
Has anyone any ideas on how to fix this until BT decide to fix the problem. Preferably a step to step guide as I have limited experience with Ubuntu. I�m using Ubuntu 11.04.
I'm trying to set up a wireless connection to my personal wireless net. I have a Linksys N router and I am using a WMN 300n adapter. I found out how to get the connection manager but I'm not sure if i ams upposed to enter the MAC of the router and I know what the SSID is but the B**ssid(not quite sure what that was and I'm on a Win7 system right now)so any info to get my wireless connection now
View 5 Replies View RelatedWhen I try to connect to the internet wirelessly with Fedora 14 it tells that the wirless firmware is missing. Is there anywayI can fix this or find the firmware for a Dell Wireless 1379 Wlan mini-chip? The Chipset is BCM4315Also my computer is a Dell Inspiron 1545
View 3 Replies View RelatedI am trying to setup multipath with failover policy on openSuSE 11. I have two qla2xxx HBA's installed and they appear to be working. Here is the output of "multipath -l" command
[Code]....
While testing, I pulled one of the two connection to SAN, and the connection failed over to second HBA connection to SAN. When I plug the cable back in, it does not fall back to original connection... It stays in failed state. Also, I noticed that failed disk (sdd disk) comes back as (sdg disk), which is probably why connection does not fall back to original HBA. But, when I run "/sbin/service multipathd restart" sdg disk shows as as enabled in multipath -l...
I need to setting up my wireless connection on ubuntu.
View 1 Replies View RelatedI am trying to setup a wireless connection between F10 and a HP J6480. I dnloaded the linux driver hplip-3.9.2, disabled the SELinux and ran the install. When I choose method of connecting - wireless it would not discover the device. The only way was to enable the USB descovery. Doing so, the computer found the printer and all is fine. What am I missing trying to enable the wireless connection. Note, that during this process, the USB was not connected. Also, I dual boot with Vista and I can run the printer wireless.
View 7 Replies View RelatedI have recently installed Ubuntu 8.04 LTS Server Edition, with no GUI. I can't connect to internet, and therefore I can't use commands like "apt-get update" I do not even know how to configure this server yet. I need my server to connect to Internet through my wireless card (I have no cable connexion for now).
View 4 Replies View RelatedMy adsl modem is in bridge mode. I can connect to internet via pppoe . pppoeconf recognise the pppoe in eth0 and setup a connection and I can use it. How can I setup a pppoe connection using pppoeconf so that it uses wireless ? I set the wireless mode to bridge in modem settings. But, after that the access point stopped appearing in "aps in range" in network manager and I can't connect to it. pppoeconf also doesn't recognise wlan0 as a valid pppoe link . but dat is normal since i don't think it can check if wlan0 is pppoe without wlan0 being connected to the modem's wireless network. How can I connect to Internet with modem in bridge mode and connections via wireless interface of modem? Is pppoe over wireless even possible ? coz the datalink layer of wlan is not ethernet rite?
View 6 Replies View RelatedI tried setting up a adhoc wifi in my debian laptop, so that my other laptop running Ubuntu could connect to it. Though the access point made on Debian laptop is visible on Ubuntu laptop, I could not establish a connection.Then I used create new wireless network tab to create a connection named test1. Though it shows up on Ubuntu box, i couldnt connect to it.
View 4 Replies View RelatedI have a computer with both wire and wireless connections. Wired connection works fine, but I would also setup the wireless connection.(I also have a dual boot on this cumputer with WinXP where both wire and wireless connections works fine. So, wire and wireless configuration of the actual router is not an issue here.)
At this point I just want to know the main/overview basic steps of setting-up the wireless connection on the computer. Also if you could suggest any links to guidelines for these steps. I have been thinking about something simple like this, but I might have missed a lotInvestigate if Ubuntu finds the wifi-hardware - the installed wifi card.Investigate if Ubuntu have an installed driver for this wifi-card.Configure the Wireless Network connection, like SSID.Unplug wire connection and reboot.
I'm trying to set up a wireless or wired network (wireless would be better...) to share my connection with my housemate, as well as with some devices. The only guide I found regarding this (I must admit, I didn't have much time to put into research), was dating back to 2005, and although doable, seemed somewhat confusing. Getting to the point: is there a way (maybe a standalone program, or some kind of plugin) to share a connection?
View 9 Replies View RelatedI have an intel 5300 wireless chipset which is not supported in kernel 2.6.25. I am currently using opensuse 11.0, I downgraded from 11.1 since I faced so many other problems. can I setup my wireless driver under kernel 2.6.25? if so, how could i do this?
View 7 Replies View RelatedI'm try to setup a wireless network with my linksys wireless router and my HP laptop dual booting Vista & Suse 11.2. I have the vista networked, just fine. Where I can share files and the printer connected to my desktop. But I want to be able to use Suse in the same way, full time and to stray away from Vista. My wife and kids like easy. So I'm trying to transform them and show them something new.
View 9 Replies View RelatedI can't get the wireless to work on my laptop its a hp Pavilion dv9700 it has a Broadcom 4321AG 802.11a/b/ g/draft-n Wi-Fi Adapter i cant seem to get it set up.
View 6 Replies View RelatedI am getting trouble with knetwork manager. I created a new connection by scanning and connecting using knetwork manager. But every time connection gets disconnected and ask for password and again it connects.
View 8 Replies View RelatedI have searched and have not found anything specific to my issue. I am currently using NDISWrapper to load the bcmwl15 driver and when it's active it works beautifully.Problem is sometimes at boot, the card doesn't "turn on" and I don't know how else to describe it. The OS does not even detect that the hardware is present. I have disabled wireless hotkey in BIOS. The only way to make the wireless card "active" is to reboot with the wiredconnection to the router. After doing that the wireless card "wakes up" and works awesome.Is there anything I can do to make sure the driver load at boot?mes I get the error that NDISWrapper is not modprobbed when I go to network configuration and if I wish to do i now? I don't know if that has anything to do with the boot sequence. Using the <modprobe ndiswrapper> command as root does nothing permanant
View 9 Replies View RelatedI own an ASUS N61JV-X2 notebook PC. It has an Atheros Communication, Inc. AR9285 Wireless Network Adapter. 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 0280: 168c:002b (rev 01) I cannot see any SSIDs including my home Verizon FiOS 802.11 G WPA2-AES-TKIP encrypted network. I went to Starbucks to try to connect to their free Wi-Fi and I could not make a connection. How do I solve this problem so that I can connect to a SSID of my choice and make a wireless connection while using GNOME 3?
View 2 Replies View RelatedI recently bought a D-Link DIR-655 router capable of 802.11n operation, upgrading from a DIR-624 router only capable of 802.11g operation. While my overall setup uses wired connections, other people in the house prefer wireless, and the upgrade was undertaken more for a hoped for increase in wireless range, rather than the possibility of increased speed, since the router is located to accommodate the wired connections. However, to test the 802.11n operation I bought a D-Link DWA-130 USB dongle for my now 5-year old laptop, which comes with an otherwise satisfactory 100Mbs ethernet port(eth1) and an 802.11g wireless card(eth0). By checking the dmesg | grep firmware output after I plugged in the dongle I determined that the necessary firmware was rtl8192sfw.bin, which I found on the web, and downloaded into the directory /lib/RTL8192SU.
A subsequent reboot and then YaST > Network Devices > Network Settings showed the device as wlan0, but not configured. I changed the Network Setup Method to ifup (since I can see no way to do a device configuration in Network Manager), and configured the device, and at the same time deleted the configuration for the existing 802.11g wireless card(eth0). I then rebooted, went back into YaST to confirm the wlan0 device was configured and the 802.11g device (eth0) was not, changed the Network Setup Method back to Network Manager, rebooted again. Making sure that the router was set to only transmit/receive using 802.11n I then typed iwlist scan. To my surprise, the output showed first that the supposedly unconfigured eth0 device seemed to be still active, for it found my home network, and claimed that the protocol used was 802.11g. On the other hand, the newly configured wlan0 device produced the message: "Interface doesn't support scanning: Network is down".
First, should I expect iwlist scan to work for a device that shows as unconfigured? And even if it should work, shouldn't it show 802.11n as the protocol, assuming that the router is in fact telling the truth? Is there any independent means to determine if the router is only using 802.11n as it claims? Second, the overall goal is to make the wireless network in the house 802,11n only, and since the dongle is backward compatible with 802.11g, I would expect to permanently unconfigure the eth0 device and use the dongle, both here and on the road. I do not need two wireless connections on my laptopThe laptop is running SuSE 11.2 as of about a month ago. Some relevant(I hope) command line output:siracusa:~ # uname -aLinux siracusa 2.6.31.12-0.2-desktop #1 SMP PREEMPT 2010-03-16 21:25:39 +0100 i686 i686 i386 GNU/LinuxUSB Information
siracusa:~ # lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 2001:3301 D-Link Corp. [hex]
[code]....
I just started using OpenSUSE on an old laptop. It seems that I have my graphical problems at least temporarily solved, but I continued to lose my wireless connection after an hour of use. This is an old and well supported chipset (RT2500) and I had never had any issues with it before. I use WPA security, and one kind poster suggested I had a line for using the old "wext" driver in the /etc/sysconfig/ifcfg-wlan0 file, and that seems to have sorted it since I have not had any further issues since doing that edit. I eventually found the information on my own:
# Note: This option requires a wpa driver supporting it, like
# the 'nl80211' driver used by default since openSUSE 11.3.
# When you notice problems with your hardware, please file a
[code]....
I recently took a WIRED internet connection (from the people who provide cable TV) and switched from ubuntu to openSUSE11.2. . I am not able to set up an internet connection in openSUSE 11.2. I have been given a static IP, and the following info
subnet mask
gateway
dns server
alternate dns server
how do i setup an internet connection with these in openSUSE 11.2.
Today I switched from Ubuntu to OpenSuse. But I can't setup my Ethernet connection.I have 2 PCs connected with a crossover cable, one with Ubuntu, the other with OpenSuse 11.3. Lights are on in both NICs.
View 9 Replies View RelatedThere seem to be a number of people that believe the junk that NetworkManager is buggy.As I believe the opposite, I want to offer more detailed instructions on how to create the initial connection, and how to troubleshoot the process. Once readers of this group have commented on this draft, I plan to ask the moderators to make it a sticky.
This description will be specific to the KDE desktop. The steps will be similar for Gnome, but the details may be different.
Step 1: Do you have a Network Manager applet in the system tray? If not, use YaST =>
Network Devices => Network Settings. Under the "Global Options" tab, click on the "User Controlled with Network Manager" button. If it is already set, you will get a warning box when "Network Settings" starts.
Step 2: Now you should see the NM applet. Click on it and check the popup. If the "Enable Wireless" checkbox is inactive (gray), there are several possibilities: (1) Your wireless device driver is not loaded, (2) the necessary firmware is not available, or (3) an rfkill switch/button is wrong. For (1), check "hwinfo --network" and check the "Driver" line. If it is blank, then you need to run the command "/sbin/lspci -nn" if the device is connected to a PCI bus, or "lsusb" if a USB device. Post the results on the Wireless forum. For (2), look at the output of "dmesg | grep firmware", which will list the name of the file(s) to be loaded.
For Broadcom devices that use either b43 or b43legacy, the firmware is obtained by using the command "/usr/sbin/install_b43xx_firmware". You will need a wired connection to complete this step. For (3), you will also need a wired connection and install the
"rfkill" package using the command "sudo zypper in rfkill". The interrogate the current settings with "/usr/sbin/rfkill list". If any device is "Hard blocked", then wireless will be disabled.
Step 3: Once the "Enable Wireless" checkbox is active, check it and click on "Manage
Connections". Choose the Wireless tab and click on Add. Enter the name for this connection. You will probably want to check the "Connect Automatically" box. Next click on the Scan button. If you do not see your Access Point (AP) in the map, you will not be able to get a connection. Click on the AP you want, and click OK. The (E)SSID should be in the SSID box. The other boxes on this screen should be OK as is. If you have several APs with the same SSID, but you wish to restrict the connection to only one of them, then you should enter its MAC address in the BSSID box.
This usage is rare. Next click on the "Wireless Security" tab and enter any encryption secrets. The correct type should have been selected. For WEP encryption, you will need to use the hex key, not a passphrase. Once this is complete, click OK to close this screen, and the configure screen. During this process, a popup should appear offering to use a
wallet to store the connection secret. If you use a password on this wallet, you will need to enter that password each time you log in. If you set no password on the wallet, the security level is lowered, but entering a password is avoided.
Step 4: At this point, you will need to disconnect the wire. Whenever the computer can make a hard-wired connection, it will supersede any wireless option. The wireless connection should then occur automatically.
I set up 11.4 in my laptopnd, after updating and downloading the proper firmwareeverytihing runs great. I already configured the wireless network via the standard NetworkManager but the connection never starts automatically. When I boot up it reports all the wireless connections available and also let me connect to hidden networks (mine is not broadcasting so I have to use this option). I had to reconfigure my network options the first time I selected Hidden Networks but it connects fine. Please note I had already selected the "Automatic connection" optionSo the only question is how I configure my equipment so it connects automatically to the already configured network
View 3 Replies View RelatedI've been having problems with connecting to my router with my wireless card. Sometimes knetworkmanager attempts to the connect to my wireless via it's saved profile but it just stays on "Activating" for about 45 seconds then just stops. This only started happening a few days ago, so maybe the new kernel update has something to do with it?
I've tried to debugging the problem myself and have found if I reboot my router knetworkmanager can connect immediately to the wireless router, but also something interesting I found was is I assigned a IP Address and DNS manually on the saved profile it would connect with no problem (No reboot of router required), so it is indicating there is a problem with getting network settings. I've confirmed that the wireless card is not hard or soft blocked through rfkill.
I was using the box standard ath5k driver when this problem started happening and even went as far as a complete reinstall but ironically enough on first boot from a fresh install my wireless could not connect with the problem described above. I've since moved to the compat-wireless drivers but the problem remains.
I checked a couple of logs, one log file of significance was the wpa_suppliment log which was full of these messages: From all my debugging I can only assume that the kernel update is a possible cause for all of this as the problem occurring on first boot of a fresh install sounds like a general bug. I've got all of the requested information about my wireless card below, hope I've got everything:
[Code]....
Some info below:
- notebook Fuijtsu Siemens AMILO Pro2065 - 4 gb ram - 80 gb hd - wireless on board Intel PRO/Wireless 2200BG
- wireless works properly with Ubuntu (with WEP key)
I'm just installed OpenSuse 11.2 and:
- wireless found my AP
- i've just inserted WEP key / 64 bit Hex-Ascii and..not working!
