I recently setup ubuntu 9.10 in my desktop..I don't know whether the connection is dialup or not. I used the connection with cable connection. I have got the following information from my ISP:
User name: n372_asad_go@brisksys.net
service name: brisknb
password: 16251521
I am trying to setup multipath with failover policy on openSuSE 11. I have two qla2xxx HBA's installed and they appear to be working. Here is the output of "multipath -l" command
[Code]....
While testing, I pulled one of the two connection to SAN, and the connection failed over to second HBA connection to SAN. When I plug the cable back in, it does not fall back to original connection... It stays in failed state. Also, I noticed that failed disk (sdd disk) comes back as (sdg disk), which is probably why connection does not fall back to original HBA. But, when I run "/sbin/service multipathd restart" sdg disk shows as as enabled in multipath -l...
I followed the tutorial found here [URL] but when I try to access [URL] I get the following:
Code:
Secure Connection Failed
An error occurred during a connection to www.mydomain.com.
SSL received a record that exceeded the maximum permissible length.
(Error code: ssl_error_rx_record_too_long)
Not sure what I might have done wrong... I have retraced all of my steps and I don't believe I missed anything.
I'm trying to setup PPPoE connection to establish my DSL connection, but I got
Code:
pppoe[3885]: read (asyncReadFromPPP): Session 4479: Input/output error
pppd[4104]: Cannot determine ethernet address for proxy ARP
in my sylog file.
When I do pppoe-start, it connected but I cannot ping into any destination (even to my modem in the same network). DNS servers are explicitly set in pppoe.conf and resolv.conf. Did I miss anything?
I got this error for two days.back then I googled this error and i got some information about log file in /var/log/syslog but i couldn't find it in google at all. this is all i got from syslog . look at the red paragraph
[Code]....
I'm trying to get VPN working so that I can browse "from the UK". I got myself a free one hour trial but it's no good, because I can't get it to work!
I added the network using the network manager. I put 'uk.hideipvpn.com' in "gateway". I left "NT domain" blank as I didn't know what it meant.
It says "The VPN connection 'VPN connection 1' failed. I found the following at /var/log/messages:
Code:
I setup a PPTP VPN connection in ubuntu 9.10 (x86_64) using NetworkManager. After enabling the VPN connection, I can browse web pages (it's perfect) but after a while the vpn connection is terminated! The following is my syslog after connecting and terminating:
Code:
Mar 12 22:10:10 amir-desktop NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'...
Mar 12 22:10:10 amir-desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' started (org.freedesktop.NetworkManager.pptp), PID 2204
[Code]....
A while ago i attempted to use ubuntu as my default operating system and it failed, i could not get the shares to work properly and i gave up. Yes i know, may be i should have kept going.
Any way, my problem is, Im attempting to use ubuntu 11.04 now, and this time i am realy keen on going through with this, however... for some reason when i connect my wired connection cable ubuntu keeps failing to connect. this is with the auto eth0.
Can any one help me with this problem? This is one of the major things that i will need to do if i want to switch over to ubuntu.
I am trying to set up my Ubuntu 10.04 netbook to see my WinXP desktop's files and vice a versa. I followed the steps in this tutorial thread: HOWTO: Setup Samba peer-to-peer with Windows. I got as far as "Time to add yourself as an samba user." at this point I keep getting the following error:
Code:
sudo smbpasswd -L -a WinXP_User_Name
New SMB password:
Retype new SMB password:
Failed to add entry for user WinXP_User_Name.
My WinXP machine has no password.
My conf file is here:
[global]
; General server settings
; netbios name = WinXP_Computer_Name
server string =
; workgroup = WinXP_WorkStation_Name
announce version = 5.0
socket options = TCP_NODELAY IPTOS_LOWDELAY SO_KEEPALIVE SO_RCVBUF=8192 SO_SNDBUF=8192
passdb backend = tdbsam
security = user .....
I need to setting up my wireless connection on ubuntu.
View 1 Replies View RelatedI've just done a fresh install of Ubuntu 10.04 lucid lynx and how to setup a pppoe connection in ubuntu. ( thats after 2 hours of googling and trial and error)
system info: its a laptop : Dell Studio XPS 16 connected to a Ethernet hub thats connected to a dsl modem..
I have backtrack 4 os on my acer netbook and i want to create a vpn connection! how to setup the vpn connection?
View 1 Replies View RelatedSo I got Ubuntu 9.10 on my laptop working really neat and wanted to upgrade my desktop to 9.10 as well. So I reinstalled Ubuntu there and now I can't connect to my network anymore....
I have a usb wireless adapter (currently Sitecom as I bought a new one today to hopefully fix it, but ended up at exactly the same problem as with my old adapter). The network manager I'm using now is Wicd since some topics I was looking through were about malfunctioning GNOME network-manager (which I removed) and suggested to try this. The GNOME network-manager kept prompting to insert my WEP network key which was a correct one. When I removed all security from the network it didn't prompt anything anymore but just failed to connect. The Wicd network manager is so nice to tell me that it cannot obtain the IP address however, so I suspect that this is my main issue... but I have no idea what I can do about this? Tried using a static IP and then I get the message "Connection failed: Could not contact the wireless access point."
I feel powerless as my knowledge here is just lacking..
Dual boot Vista Basic and Ubuntu 10.04 on low spec PC. I can connect to the wireless when I am next to it. I move to the room where the computer is normally used and I lose connection. I can still see it but it fails to establish a connection. Okay, sounds like it's just too far way but when I re-boot and use Vista, it works fine (1 or 2 bars, but it works). Is this a driver issue? Anything I can do apart from move my wireless router?
View 9 Replies View RelatedI use Nokia N900 under T-Mobile as a broadband modem. It is connected via USB. There was no connection problems under 10.04 or 10.10. Now I have installed Ubuntu 11.04, and I cannot connect any more.
Here are the log messages that I get when trying to connect:
Code:
May 30 14:32:06 ubuntu-sager NetworkManager[759]: <info> Activation (ttyACM0) starting connection 'T-Mobile Internet'
May 30 14:32:06 ubuntu-sager NetworkManager[759]: <info> (ttyACM0): device state change: 3 -> 4 (reason 0)
[Code]....
My adsl modem is in bridge mode. I can connect to internet via pppoe . pppoeconf recognise the pppoe in eth0 and setup a connection and I can use it. How can I setup a pppoe connection using pppoeconf so that it uses wireless ? I set the wireless mode to bridge in modem settings. But, after that the access point stopped appearing in "aps in range" in network manager and I can't connect to it. pppoeconf also doesn't recognise wlan0 as a valid pppoe link . but dat is normal since i don't think it can check if wlan0 is pppoe without wlan0 being connected to the modem's wireless network. How can I connect to Internet with modem in bridge mode and connections via wireless interface of modem? Is pppoe over wireless even possible ? coz the datalink layer of wlan is not ethernet rite?
View 6 Replies View RelatedI have BIG troubles trying to set up wired internet connection in Ubuntu! To be able to connect to the internet I have to enter my MAC address, 2 IPs, netmask and 2 DNS address. When I try to edit the default internet connection eth0 with my correct information, the minute I enter my MAC address and save the changes the network manager creates new internet connection with wrong data and use it instead! I can't select the correct internet connection from the top bar where the internet icon is, because it is just not there. The only connection that I can choice is the new default one with the wrong data! If I try to create new separate internet connection with my correct data the same thing happens! The moment I enter my MAC address and save it, the internet connection disapears from the list of internet connections in the internet area in the top bar and I can't select it. I tried googling it, but with no luck I think that if I set up my connection trough the terminal everything will be ok
View 2 Replies View RelatedI tried setting up a adhoc wifi in my debian laptop, so that my other laptop running Ubuntu could connect to it. Though the access point made on Debian laptop is visible on Ubuntu laptop, I could not establish a connection.Then I used create new wireless network tab to create a connection named test1. Though it shows up on Ubuntu box, i couldnt connect to it.
View 4 Replies View RelatedI'm having a problem with Subversion. When I try an "svn up" it gives me this error message:
SSL handshake failed: Secure connection truncated
I'm running Ubuntu 10/4 but I also had this problem with 9/10. Does anyone know what this error message means? It appears to be an SSL problem but it's not clear to me what exactly the problem is. I do not have this problem with svn on my other office computer, nor my home computer. FYI, I'm running subversion on the Regina project.
The full error message is this:
Code:
svn up
svn: OPTIONS of '[URL]': SSL handshake failed: Secure connection truncated [URL]. Although I don't think there's anything specific to Regina about this svn problem, as I mentioned, I can "svn up" from home, or from my other office computer.
I installed Ubuntu 10.4 side by side with my Vista. This is on a PC I leave on permanently and use as a sort of Sever, so Security and Network connection are VERY important on this device. I use it for documents and IP PBX (telephone system). I currently use Vista and 3CX, but I plan to roll it over to Unbuntu full time once its up and runnng correctly - I will just need to change the Grub2 conf priority. After install, all was fine and I managed to make many changes to settings, apps and updates, but I have noticed in the past week when going in to make further changes the network has suddenly stopped working! According to Network Manager and the icon on the panel it is connected and I can not see anything obvious that is not correct. I tried doing a PING (192.168.1.1) from Network Manager to the main router, but it failed. I know that there is nothing wrong with the network nor the card or PC it all sits on. It's working now with Vista and my other machines. It must be a config some-where.
View 9 Replies View RelatedI keep getting this error message:
The VPN connection '<insert name here>' failed because of invalid VPN secrets
I have Ubuntu 10.10 installed on a Dell Latitude D600. It's a fresh brand new install. After I installed all the updates, I proceeded to install network-manager-vpnc. Then, I imported .pcf files so that I can connect to the office VPN,but it gives me the error message above.I have gone to ~/.gnome2/keyrings and renewed everything.Tried moving them away, and then back again. Created a new keyring. Nothing.
I need to connect to my company through a Cisco VPN. The Cisco client fails to build so I thought of using vpnc. I used Network manager (NetworkManager-vpnc is installed). However after setting everything up and then logging in, I get the 'VPN Connection Failed' message.
View 14 Replies View RelatedI have a computer with both wire and wireless connections. Wired connection works fine, but I would also setup the wireless connection.(I also have a dual boot on this cumputer with WinXP where both wire and wireless connections works fine. So, wire and wireless configuration of the actual router is not an issue here.)
At this point I just want to know the main/overview basic steps of setting-up the wireless connection on the computer. Also if you could suggest any links to guidelines for these steps. I have been thinking about something simple like this, but I might have missed a lotInvestigate if Ubuntu finds the wifi-hardware - the installed wifi card.Investigate if Ubuntu have an installed driver for this wifi-card.Configure the Wireless Network connection, like SSID.Unplug wire connection and reboot.
I have a similar problem. My ubuntu box is set up as a dhcp router for my Xbox360, my xbox can get ip and DNS information from the computer, but it doesn't seem to get the right info. The ip address it gets assigned is out of the range I've set in etc/dhcp3/dhcpd.conf.
View 1 Replies View RelatedI have a 2G Broadband service through my Ethernet cable. My provider in China has a user name and password to login to their service. I don?t have a modem or anything but the wire coming in from the outside. It is setup in windows but I can?t figure out how to do it in Ubuntu 11.04.
View 1 Replies View Relatedi am accesing internet via proxy server till now...now i switched from proxy server to broadband connection. can't able to setup internet connection.
View 2 Replies View RelatedI have an eeePC 1000HG, basically identical to the 1000H but with an integrated 3G modem.
Mostly the netbook works fine, the only big problem is the 3G modem will not connect to the network.I added a "Mobile Broadband" network connection from the network icon at the top right.The OS has detected a modem, it reports as a "HUAWEI Technology HUAWEI Mobile" in the mobile broadband network setup wizard, and as the follwing with lsusb;
Bus 001 Device 002: ID 12d1:1001 Huawei Technologies Co., Ltd. E620 USB Modem I don't know whether that's correct - I can't find information anywhere which definitively specifies which model of modem is in there.... I did find some reference to it being a Huawei E770V, but I don't know if that's true or not. I have installed the modeswitch packages from Synaptic, which made no apparent difference.
I followed the wizard and picked Australia as a location and Virgin Mobile as a provider and Mobile Broadband as a billing plan.When I try and connect I just get an error saying the connection failed.The modem worked out of the box under eeebuntu 3.
I've been at this the last 3 hours now or so. I am not a very good with Linux, I am fine with all other areas. I have this laptop, with a Intel Pro 2200BG card. The idea was to install a lxde lightwieght on it and use PCLINUXOS, because its "easy". This computer is for internet browsing and thats it. Under the Network Center -- I can see all networks, including neighbours. When I try to connect to my router via Wireless, I get connection failed over and over.
I then tried doing all the following:
Changing the router from WEP to, WPA, WPA2 personal, WPA2 Enterprise
Changing the SSID, broadcasting to ON, changing the SSID name
I've used various different passwords, and reset the router now about 50 times. I am connecting to my Router (as Ive changed the SSID and noticed it picks up the new name). (Yes I can see the correct MAC addreess). Yes I am on the right channel, all good here.
My Nintendo DS is connecting fine with all the changed settings now. The wireless card worked fine under Windows XP (However I just removed the operating system since I really had no need for it). I've tried every other mode, it works wired. Like I had explained above, I downloaded a what I thought was an easy verison (distro), I was really hoping to get away from the crazy windows life with crazy errors and instability.
I did try enabling display log, and doing it manually by adding a connection, etc. The log tells me about as less would a windows event log: it says
Problems occurred during the network connectivity test
This can be caused by invalid network config or problems w/ your momde / router
Reluanch, etc.
I can connect to the internet fine with wvdial and wvdialconf; heck I am even posting from my PCLinuxOS FM Distro. I want to setup an ethernet connection between two PC's, one running PCLOS 2010.11 FullMonty and the other Knoppix 6.2.0. Knoppix is fine and setting up a connection is simple but with PCLOS I have been having many problems trying to set it up. I tried using the drakconnect tool but it did not work. I tried assigning it a static IP Address but the other PC would still not pick it up and to to it all I keep getting the same error message about problems during the network connectivity test!
I'm trying to set up a wireless or wired network (wireless would be better...) to share my connection with my housemate, as well as with some devices. The only guide I found regarding this (I must admit, I didn't have much time to put into research), was dating back to 2005, and although doable, seemed somewhat confusing. Getting to the point: is there a way (maybe a standalone program, or some kind of plugin) to share a connection?
View 9 Replies View RelatedI am trying to setup a wireless connection between F10 and a HP J6480. I dnloaded the linux driver hplip-3.9.2, disabled the SELinux and ran the install. When I choose method of connecting - wireless it would not discover the device. The only way was to enable the USB descovery. Doing so, the computer found the printer and all is fine. What am I missing trying to enable the wireless connection. Note, that during this process, the USB was not connected. Also, I dual boot with Vista and I can run the printer wireless.
View 7 Replies View Related