I have just installed ubuntu 7.10 on my computer. The problem is getting it connected to the internet using my Sony Ericsson w580i as a modem. I have used my phone to connect to the internet on XP operating system easily. Please assist me and try to give me a more simplified step by step procedure.
View 9 Replies
I have a nokia phone, cant recall the model number, but its gprs enabled and i can check my mail on it. Its got a vodafone simcard and theres a packet data connection. how i can set it up with my laptop so as to access the internet using the phone as a modem...?
View 1 Replies View RelatedI was recently asked to get a 3G ZTE 633 modem (not in stores) to connect to the internet whenever it was plugged in. I had it successfully working on my Ubuntu Gutsy Gibbon machine but it does not work on Fedora 10 which is where it is required to work. When the 3G modem is plugged in I use a Udev rule to run usb_modeswitch which changes it from being in usb storage mode to being in modem mode. This part works fine. I then run a second udev rule (on the modem device), this should run a script which connects to the internet. Unfortunately it falls over here. The script does run but it will not connect. However if I run the script manually from root it works fine. I guess that it is a permissions issue.
The device permissions are:
crw-rw---- 1 root uucp 188, 0 2009-04-26 11:31 ttyUSB0
crw-rw---- 1 root uucp 188, 1 2009-04-26 11:31 ttyUSB1
crw-rw---- 1 root uucp 188, 2 2009-04-26 11:31 ttyUSB2
The script and script folders permissions are:
drwxrwxrwx 2 root root 4.0K 2009-04-26 11:46 .
drwxr-xr-x 23 root root 4.0K 2009-04-26 11:13 ..
-rwxr-xr-x 1 root root 95 2009-04-26 11:46 run_internet
One thing to note is that there are three udev devices associated with the modem. They are ttyUSB0, ttyUSB1 and ttyUSB2. I use ttyUSB2 to talk to the modem when connecting. Here are the files. If you require any more let me know:
The first udev rule:
SUBSYSTEM=="usb", SYSFS{idProduct}=="2000", SYSFS{idVendor}=="19d2", RUN+="/usr/bin/usb_modeswitch"
The second udev rule:
SUBSYSTEM=="usb", SYSFS{idProduct}=="0031", SYSFS{idVendor}=="19d2", MODE="0666", RUN+="/outputs/run_internet"
The script:
#!/bin/bash
/bin/echo script
/usr/bin/wvdial &
cp -f /etc/telstra_resolv.conf /etc/resolv.conf
The wvdial config file:
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = ATS7=60 S30=0 S0=0
Init4 = AT+CGDCONT=1,"IP","telstra.internet"
Modem Type = Analog Modem
Baud = 9600
New PPPD = no
Modem = /dev/ttyUSB2
ISDN = 0
Dial Command=ATD
Phone = *99#
Password = user@bigpond.com
Username = password
Stupid Mode = 1
So what am I missing? I suppose it is related to device permissions. Why does the "mode" command not work? With what rights do udev rules run?
trying to connect to the internet using wvdial but facing problems. the command runs fine until i get PID ppd Carrier detected. Starting PPP immediately.
--> Starting pppd at Sat Oct 23 10:40:09 2010
--> Pid of pppd: 2520
nothing happens after this.. I checked the resolve.conf and it is empty. i put openDNS server addresses but still did not work.
i'm having problems connecting to the internet unless i manually enter the IP info.
automatic DHCP does not work. I'm on a dual boot machine vista/ubuntu 10.04 LTS connecting to the internet through a lynksys wireless g router and a cable modem.
I'm trying to get internet to my old server through a laptop. The laptop is running ubuntu 10.10 and the tower is running ubuntu server 10.10 X86.
View 1 Replies View RelatedI recently set up a network of computers via Ethernet, all of which use Fedora 10. I would like to be able to get any computer on the network to hook up to the internet.(I think the solution is now figured out - see below, on page 2, "problem solved")
View 14 Replies View RelatedI am having a problem with my internet connection. It only works half the time. Usually when i start the computer it doesn't connect until i restart anywhere from 1 - 10 times. I did sudo ifconfig while it was not working here is the output:
eth0 Link encap:Ethernet HWaddr 00:19:d1:00:36:41
inet6 addr: fe80::219:d1ff:fe00:3641/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:11 errors:0 dropped:0 overruns:0 frame:0
[Code]...
i have three type of linux distributions installed on vmware- centos 5.5 , rhel5, fedora14.i have installed centos 5.5 on a seprate hard disk.i want to use internet on linux using my nokia 2630 cell phone.how to connect my phone through bluetooth to use internet?
View 13 Replies View RelatedI am wanting a computer with an external dialup modem (ppp0 modem through a com port /dev/ttys1) to act as a gateway to the internet, forwarding internet traffic through ethernet (eth0 is set to static 192.168.2.2) to a router (the router is 192.168.2.1) where it will be broadcast to other wireless computers like my laptop (192.168.2.3). I've had this setup until recently when the gateway computer (the one with the modem) died. Now I'm replacing that machine with another box and an install of Ubuntu 10.10 but so far things aren't working for me.
Success so far:I have dialup access working on the new box. Took me a while to work out the configuration for getting dialup working, though the IP address is Dynamic (or it won't stay connected), "Check carrier line" is off, and "Ignore Terminal Strings (stupid mode)" is on in order to successfully connect and stay connected to my ISP. I also had to make my normal (non-root) user "lancer" a member of the "pid" group (the reboot) in order to use gnome-ppp as non-root. The laptop (192.168.2.3) is successfully connecting to the router (192.168.2.1) as I can see the router configuration page when I type http://192.168.2.1 into the laptop's web browser. This setup is unchanged from how I had it before when this was previously working and I don't want to change how the router itself is set up. What I want is to know what to fix in the new box in order to get it connected to the router (through ethernet) and bridging the internet through.
My problem is that whenever I plug in the eth0 from the gateway (192.168.2.2) to the router (192.168.2.1), Ubuntu's automatic plug-me-in network detection kicks in and I find my dialup no longer working through some kind of IP conflict (at least that's what I think it is). Maybe I don't have the "gateway" correctly assigned? (in the gateway computer for the ethernet connection, I had it pointing to itself as I don't know what to put for "gateway IP" as that is automatic So, just to check my connection, here I am pinging google (from the gateway computer which has the dialup modem) once a dialup connection has been made.
Code:
lancer@lancer-desktop:~$ ping www.google.com
PING www.l.google.com (74.125.237.17) 56(84) bytes of data.
64 bytes from 74.125.237.17: icmp_req=1 ttl=55 time=179 ms
64 bytes from 74.125.237.17: icmp_req=2 ttl=55 time=176 ms
64 bytes from 74.125.237.17: icmp_req=3 ttl=55 time=158 ms
[Code]...
What do I need to do in order to make Ubuntu of my gateway computer stay connected to my dialup but also simultaneously share an ethernet LAN to my wireless router and feed traffic to the other computers from there? I have googled this but some of the most promising instruction (e.g. http://www.ubuntugeek.com/sharing-in...in-ubuntu.html) call for packages like dnsmasq or ipmasq which seem defunct now in Ubuntu 10.10. Other pages seem to suggest dual-networks "can't be done" in Ubuntu [URL].. (what!?! I had it before my other gateway died)
I managed to configure my W890i phone to get access to internet through an ubuntu-based computer. It's very easy to use the phone to give internet access to the computer, but the opposite is quite more tricky. For that I've done the following
----On the phone---
-Set the USB network option to "through computer", so that the phone uses the computer's internet connection and not the opposite.
-Decide and set "Shared Network" parameters: user, pasword and workgroup.
-In "conectivity-> internet connection" set "allow local network" to "yes"
----On Ubuntu 10.04---
-Install samba, samba-client, smbfs, smbclient, firestarter and dhcp3-server
-Configure Samba (System-> Administration-> Shared folders): same workgroup as in the phone, add new user (the phone), passwd this new user. In my case the user was called "w890i" and the password given was the same.
-Once the phone is connected to the computer through USB (then select "phone mode"), a new connection appears in NetworkManager: usb0.The aim is to create a shared network that gives internet access to this device. Edit the IPv4 parameters of this new connection, set them to Manual and give an IP adress (192.168.0.1) and a subnet mask (255.255.255.0); the rest of the fields are left empty.Connect this network.
-Set firestarter to use dhcp3: sudo ln -sf /etc/init.d/dhcp3-server /etc/init.d/dhcpd
-Launch firestarter and follow the wizard. Set "allow internet shared connection", choose the device for the primary internet access, and then the device for the shared network (usb0). Then change the settings for firestarter: activate DHCP for local network, set IP to the one we gave before (192.168.0.1).
-Open dhcp3-server config file sudo gedit /etc/default/dhcp3-server And set INTERFACES="usb0"
-Set the policies of firestarter: in incoming connections, allow connections from the IP adress given to the phone (192.168.0.1). Then add rules for the ports that need to be open for this connection. I opened HTTP, HTTPS, SMB, SMTP, POP3, IMAP, IMAPS, DHCP for all the connections in the local network.
-Apply policies and start the firewall.
------------
After all this, the phone can access the internet through the computer. Two problems appeared:
1. I couldn't get access to https sites, like webmails. The phone gave a "communication error". But then I tried with Opera instead of the browser built in the phone's firmware, and I could finally get to https sites.
2. I couldn't retrieve mail, neither POP nor IMAP nor IMAPS. I thought it was a firmware problem again, and I tried out several mobile phone email clients written in java, but none of them worked.
So this is at the moment the problem. If I connect from the phone to the internet directly through 3G, the email clients work for all my accounts. I don't think it's a firewall problem, because the ports are opened for this connection
Is it better to use a Usb to Serial Adapter Cable or a PCI Serial Port Card when attaching a serial port modem to a computer that doesn't provide onboard serial ports?I am leaning toward the USB to Serial Cable but do they work as well as a Serial Port Card? I have a US Robotics business class external serial modem that that I'd like to keep using for dialup internet connections.Here are the devices I am thinking of using:
USB To Serial Cable: KINAMAX CB-RS232 (Prolific Chipset)
PCI Adapter Card: SYBA SD-PCI 15024 --single port chipset=SB16C1052PC1
I am using Ubuntu 10.04 LTS. my PC is a Compaq Presario SG3043IL with a D-Link GLB-802C ADSL 2+ Router. previously i was not even getting connected to the modem but now some how i have connected my ubuntu to the modem but no way can i connect to the internet. the internet connection workins fine whenever i log on to my XP. need to connect to the internet.
View 2 Replies View RelatedI have been looking for a piece of software that can do the following; however, I am unsure what category of technology it would fall under. In addition, I am not sure if I am describing it correctly. I am looking for a piece of software that will allow a Bluetooth connection between my desktop, and cell phone. I then can place a Internet based call (SIP software, Skype, Google Talk) via the cell phone, which has been connected to the desktop system by Bluetooth.
I want to be able to receive and send calls via the cellphone, but use Internet for my calls. What got me thinking about this is a house phone I have by Panasonic, which has the capability to pair your cell phone via Bluetooth to the main base-station. This allows the option to answer calls to my house number, via my cell phone.
Ist column shows different customers( like N customers are there) , they require different bandwidht links based on some resolution time will be generated and we have to fix this line with in this resolution time , if not before 1 hr for each customer , this has to genetate some alarm and send the SMS to the particular mobile numbers.everythig is there in the GUI like customer , how much BW they want and what is the time duration , only thing we have to do is ,, linking with the GUi and writing some code to send the generated alarms to the mobile numbers specified.
View 5 Replies View RelatedIs it possible to connect to a router via a standard phone cord?
View 13 Replies View RelatedI need to setup my Sony Ericson C510 phone modem in Ubuntu linux the latest one that I have installed. When I connect my Phone using USB connection it doesnt show me the Dialog box where it says create new "Mobile Broadband Connection". I am not sure how can I configure my Tata Docomo GPRS Connection to use it with Ubuntu.
Here's one blog i came across which says:- Its wonderful to see people browsing in their mobile phones at work places and while they travel. Many Telecom companies provide cheap GPRS / EDGE based internet connectivity which can also be connected to a computer. Here, I will explain how to connect TATA Docomo Internet service in your Ubuntu machine.
[Code]...
i'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug
HTML Code:
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to
[code].....
if anyone here could recommend a cellphone. My main requirement is that it should tether as a 3.5g modem via USB to a PC running Fedora 13. I have previously used a Nokia to good effect, but their standpoint on privacy is making me look for a different brand.
View 11 Replies View RelatedI just installed Ubuntu 9.10 and its great. However when I connect to the internet at home it shows that the connection has been established but I still cant connect to the internet. My flatmates are all able to connect. However, I am able to connect from work both wirelessly and through an ethernet cable.
View 2 Replies View Relatedim trying to be able to tether my android cell phone to my fedora 13 to use as a router/modem i have gotten it to work on a friends Ubuntu OS i used the app easy-tether but it will work not on fedora
View 11 Replies View RelatedIs there a way to make phone calls and send SMS via mobile broadband 3G modem, i mean an application for the 3G modem which is similar to the one provided for windows by the manufacturer?
View 2 Replies View RelatedThis problem started a few days ago. Whenever I attempt to connect to a wireless connection via network manager, my computer completely crashes, going to a black screen with no input from keyboard or mouse. It forces me to reboot using the power switch. Everything works fine when I connect to an ethernet cable, so I am sure it's a problem with my wireless driver.
I already tried (successfully) reinstalling the ath9k driver via compat wireless as was the advice from other forums, but this had no effect. I'm currently running opensuse 11.4, and haven't had this problem until a few days ago
This problem seems a bit ridiculous for a task as simple as connecting to a wireless network, so I'm convinced that either there is some sort of relatively simple way of fixing it, or windows really is the only decent operating system out there..
I am using ububntu 9.10,and have a cable modem internet connection. All I have is an ethernet cable given to me,and when plugged in a windows machine and fire a browser am redirected to default login page where i can login, but when i plug it into my linux machine,i cant get the same done. In network connections it doesnt shows my autoeth0, i have deleted my existing dsl settings(not autoeth0),made a new wired network,i doubt what should i put into MAC addrs field(i have put my machines mac given by lshw -c network.) What should I put in DHCP client id? Anyways when i click on network connections it says under my wired connections-device not configured properly.
View 6 Replies View RelatedIn my attempt to get my USB 3G modem to work on Ubuntu 10.04 netbook edition I have made some progress to the point of getting the driver for it up and running, though connecting to the Internet after defining a profile is an issue. I have followed this ubuntuforums thread simply to get started with the usb modeswitch to get the usb modem identified by the system.
Debug information:
uname -r:
Code:
2.6.32-23-generic
cat /etc/issue:
[code]...
I've recently installed Natty and the only problem I have with it so far is attempting to connect my Huawei E5830 Three Wireless modem via USB and successfully connecting to the Internet from it. I've fiddled around with the network settings and nothing, I've also done some work in the Terminal to try and correct the problem.
View 1 Replies View RelatedI like playing around in linux. I have Windows 7 Home Premium which does not have Remote access.I want to be able to control my computer from my android phone. Which verison would be best. I was going to try out Linux Mint 9.
View 2 Replies View Relatedrunning Ubuntu 9.10 x64bit fresh install and updated.When I connect with my 3g um150 modem it disconnects my home network?? I cannot get them to run both at the same time and of cousre the next thing would be to share the internet connection.
View 9 Replies View RelatedI use Banglalion WiMax usb dongle modem. I like to use it in ubuntu os. When I connect it to my Desktop PC's usb port, it respond nothing.
View 9 Replies View RelatedI have a USB Modem MMX 372 G to connect internet lsusb showsCode: Bus 002 Device 002: ID 05c6:9000 Qualcomm, Inc.and following is /var/log/messages when I connect the USB modem and connect it for the first time the USB modem Quote:
Jul 24 08:37:42 bond kernel: [ 110.200159] usb 2-2: new high speed USB device using ehci_hcd and address 2
Jul 24 08:37:43 bond kernel: [ 110.353219] usb 2-2: configuration #1 chosen from 1 choice
[code]....
