That is what I do to connect to Xbox Live and I just got an Insignia Blu-ray player that can only connect to BD-Live through an Ethernet connection, so I was wondering if I could apply that same concept to my Blu-ray player.
View 1 RepliesMy wireless (Toshiba laptop, 10.04 64 bit) is just hanging when trying to connect. It was working fine but now nothing. My Wireless antennae is on and my other laptop can connect with no problems. I have restarted the router and the laptop twice.
View 1 Replies View RelatedI did a clean install of Ubuntu 11.04 from a cd over windows and Ubuntu 10.04. The hardwire internet works but not the wireless.
compaq presario m2010us Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03)
~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
Can anyone provide me the details how to connect my laptop with centos5.3 to connect to a wireless network.
View 1 Replies View RelatedI have ASUS Laptop A6Rseries was running XP untill I installed Linux 9.10. Now i am having problem connecting to my wireless network. I am using Belkin router what works fine with XP, Vista and Windovs 7. Here is some information what I found
lspci
00:00.0 Host bridge: ATI Technologies Inc Device 5a31 (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
[code]....
I'm trying to install Ubuntu 10.04 on my Toshiba A200-12U laptop (with an Atheros AR5007EG wireless card), but networking is being problematic.I entered Network Configurations and tried to get 'Auto eth0' working -- I went to Edit > IPv4 settings and filled in 'Addresses' with the details of my connection:
Address: 192.168.1.254 (the local IP of my router)
Netmask: 255.255.252.0
Gateway: 94.195.208.1
[code]....
I'm not exactly sure if this should be here and not in the Hardware & Laptops section, but seeing as my only problem is with WiFi, I'm guessing this is the right place. Under Ubuntu, my laptop (an Asus K42Ja, more details below) can see wireless networks normally. However, when I attempt to connect, it fails to establish a connection. Under Windows on the same laptop (dual boot), no problems are experienced.
According to this, there's a firmware bug in my wireless chip which causes connections to get dropped. I'm not getting connections at all, but I still tried the workarounds on that page with no luck. The router is a TP-Link TL-WR340G. My previous laptop, a really old one from 2003 running Ubuntu 9.10 was able to connect to that router without problems. The wireless card was Intel on that as well (but, of course, much older). The router is set up to use WPA for security. I didn't use WPA2 as I read something a while ago about problems with WPA2 and some Linux distros. Please correct me if I'm wrong here.
If anyone's curious, I'm posting this on Ubuntu, via an ethernet cable to the router mentioned earlier. Some tasty technical bits: dmesg (the latter half of the "timed out" messages is me retrying after double-checking the WPA key)
[Code]....
After searching/googling for information related to the topic, I haven't been able to get this working in KDE. Background: I have a Dell Studio 1745 with builtin Intel 5100bg wireless card. It connects to my Linksys WRT54G router just fine in openSUSE 11.2 & 11.3 using either KDE or Gnome. In Fedora 13 it only connects under Gnome, not KDE. Those are using NetworkManager. Using traditional ifup only works in Fedora under Gnome, i.e. nothing works under KDE in Fedora.
[Code]...
My laptop has been working fine with ubuntu 10.04, and earlier today it shut down after running out of battery. I came to use itr and discovered that the wifi icon had disappeared from the panel bar, and it won't connect to the wireless networkor via a wired connection.I have had a play around with this, tried ping -c5 google.comresult was:ping: unknown host google.comand ping -c5 4.2.2.1result: onnect:etwork is unreachable.I have other computers connecting to this network and know that it is working fine.
View 8 Replies View RelatedEnvironment
Linksys WRT54G Wireless
Laptop wireless Windows/XP
Windows/XP Hyper Terminal
Desktop Server Linux OEL 5 (not wireless) cable connected to the WRT54G router port. (I can go to the Internet with this server, but not able to communicate other computers on the WRT54G Wireless Network. Even though, the Linux Server is connected to the WRT54G router port.) From the Hyper Terminal Wireless laptop Windows/XP, I want to connect to my Linux Server.
On Opensuse 11.2, I would like to connect my ipod touch to a wireless ad-hoc network of my laptop. I have no wireless WIFI-router at home, so I have to use the laptop as a router to the internet. I know I have to enter a static IP adres and my router's address, but where ? I haven't found any place under network tools to do this, only saw some fields with SSID's and MAC addresses to fill in.
View 5 Replies View RelatedI am using a dell laptop which has Dell 1397 802.11B/G Wireless Mini Card. I not able to connect to internet and was not able to detect what actual problem is weather card is not supported (i.e. drivers are not available) .
Also, if any one can point to exact process to connect to wireless Lan using fedora12.
I am trying out the Debian 6.01 Live Cd but I can't get my wireless to work. This is on an old Dell C610 laptop running Windows XP, the wireless works fine under XP. Dell TrueMobile 1150 Series Mini PCI Card (on Texas Instruments PCI-1410 cardbus control).
Here's what I have done so far. Booted Live 686. Takes a long time on this old machine but finally loads with no apparent problems. My wireless network is detected- shows up in the list - 2SAT4, along with several others in the area. I click on it, after a bit it finally comes up with the wireless authentication form, I complete this with my WPA key and hit connect. This repeats without connecting.
I then goto edit connections, and make sure the wireless "auto 2SAT4" has "infrastructure" for mode and "automatic" for MTU. It does. I also make sure the Authentication is set to "Open System".
Looking at lsmod I can see that the orinoco module seems to be loaded, I think that is what this wireless card uses.
At terminal I do a "sudo iwconfig" and see that Eth0 has no ESSID or Access Point.
I do the following:
sudo iwconfig eht0 essid 2sat4
sudo iwconfig eth0 key [WPA key number]
I then do a "sudo iwconfig" and see that Eth0 still has no ESSID or Access Point. I then do a "sudo iwlist eth0 scan" and the response is "Interface doesn't support scanning" I then do a "sudo iwlist eht0 wpakeys" and the response is there are four keys available but they are all off.
Cannot connect to wireless network using live disk
View 9 Replies View RelatedI'm at wits end...10.04 won't connect to a wireless network on my laptop, and that sort of makes it useless. What is the easiest way to revert back to 9.10? I have a dual-boot system with XP and I'd rather not have to start from scratch.
View 2 Replies View RelatedI have recently installed Ubuntu lucid lynx and at my old house I had a regular cable modem (no wifi) and never used wireless internet. I would simply unplug the ethernet from the windows desktop plug it to my laptop and I was good 2 go.have recently moved and my roommate has a cable modem w/ wifi capabilities. When I plug in I am told that I am connected but......Nothing. dont know if the problem is due to the modem having wireless capabilities when my old one did not or the fact that my roommate has a win7 laptop that is connected via wifi etc. There have been a FEW times that I have walked out plugged in and everything has ran well. when I do plug in I look under connection information and I am told that I am connected at 100Mbps but whenever I try to visit a page I am out of luck. I define newbie (as far as Linux distros) and I have tried everything including going to work w/no sleep because I'm going through massive trial & errors
View 10 Replies View RelatedI have fedora 13 installed in my laptop lenovo G450.
Inside the file networking-scripts I can find the ifcfg-wlan0.
But it can't find any SSID when I scan the network.
I tried operating manually also.
But it can't be connected to any network.
The wireless device is also powered on.
But I am not able to connect to the wireless network.
I've got my Lenovo T60 laptop wireless running without too much trouble, the only problem is when i close my laptop lid and open it again the wirelessconnection is down and i simply cant click on the network icon in the notification area to re-connect as wlan0 is inactive. If i go to System>admin>network i cant activate the interface either as the 'active' button is greyed out, the only way to get the thing to come alive again (other than a full reboot) is to toggle the wireless switch on my laptop off and then back on.Not sure this should be required, i've got the interface configured to start automatically but it doesnt seem to care.
View 4 Replies View RelatedI have been using Telstra Bigpond Wireless Broadband USB Internet for about 12 months on my Laptop with Windows Vista Operating System.
I also have an Eee PC Notebook (Linux Operating System)that previously connected to the Internet via Desktop Wireless Modem.
The problem I have now is trying to connect to the internet on my Linux Notebook using Telstra Bigpond Wireless Broadband USB.
I have phoned Telstra Technical Assistance and the told me they cannot help me because the Operating System is Linux.
This will allow you to use iphones' data plan as a wireless access point. Currently setup instructions are only posted for windows/mac using a helper app to configure the laptop. Here are the instructions I followed to setup iphonemodem2 to work under Fedora 10: Download iPhoneModem2 from a jailbroken iphone using Cydia. Create a new wireless network on Fedora with the following settings:
a) SSID = "iPhoneModem"
b) Mode = Ad-hoc
c) IPv4 Method = Automatic (DHCP)
Connect laptop and iphone to new wireless network. Start iphonemodem app on iphone. The "traffic" does not update; the "status" says "Wrong Wifi Network"; and the signal strength says 0%. However, the network connection should be there as long as you have a data signal to your service provider.
After having scoured the internet and the forums for advice, I am still not able to connect via Wireless, which is being controlled by Network Manager.The following is info I obtained from running a script that I obtained reading these forums:
* Hostname: linux-8qpz.site
* Run date and time: Sun Oct 24 10:12:58 EDT 2010
---------------------------------------------------
[code]...
Recently I have installed Fedora 14 on my other laptop. It's a dual boot with Windows 7. Everything worked perfectly fine, networking included, until my friend didn't accidently turned off the wireless by pressing a wireless button on the laptop. Since then the wireless on Fedora doesn't work. It does on Windows thought. I've tried restarting the laptop few times, but the wireless still doesn't want to work again.
View 2 Replies View RelatedI am unable to connect to wireless network in ubuntu 10.10.i have noticed that the iwlagn driver isnt been used by anything.
View 9 Replies View Relatedin linux world and have recently downloaded and installed ubuntu desktop 10.10i cannot connect to both wired and wireless ethernet on my laptopit tries to connect but fails in 30 seconds , it says"disconnected" while i am able to connect to the same in windows i have broadcom 4315 and i have tried both fwcutter and ndiswrapper but the problem persiststhe device id is 14e4:4315
View 9 Replies View RelatedI have recently installed ubuntu 11.04 on my asus eeepc1005hab. And I've had problems with the wifi. I can connect via ethernet, but the wireless won't connect. I can see the connection, but my wifi never connects. I've tried many things but it still won't work.
View 9 Replies View RelatedI have a router with 2 IBM Thinkpads connected. One Thinkpad is running Ubuntu, and the other is running XP.
They connect to the router with no problems.
I installed Ubuntu on a Sharp Moebius laptop and plugged in the network cable.
NOTHING.
I have tried pinging the laptop; nothing.
I am not sure where the problem is, because my Thinkpads have no problems connecting to the router, with both Ubuntu and XP
I run Ubuntu 9.04 on a Toshiba NB205. I am suddenly having trouble connecting to the internet using my router or my cable modem for that matter. The weird thing is that I can:(1) connect to other networks just fine, and(2) my router/internet connection work fine when plugged into my desktop.I can't connect whether I'm plugged in with the ethernet cable directly from my modem or from my router, although both work fine when plugged into my desktop. Basically two green lights show up on networkmanager but it doesn't go from there to connecting.So the usual troubleshooting of moving the wires around and trying to connect like that just suggested that my laptop doesn't connect on the one router/internet connection that I happen to need.
sudo ifconfig
gives:
eth0 Link encap:Ethernet HWaddr xxxxxxxxx
[code]....
I have finally gotten my courage up and decided to take the plunge into Linux. I bought a used HP Pavilion zt1135 laptop, and loaded Ubuntu 10.04. The laptop has no other operating system on it. Everything seems to work fine except it won't connect to the internet. I am using a Comcast cable modem, which uses DHCP and a wired connection. It works fine on my XP computer, but on the Ubuntu laptop it claims there is no network connected. Firefox gives a message something like "No server found".
I have tried recycling the power to the modem and then booting up the laptop. I have tried unchecking "Enable Networking" and then re-checking it. I have checked the ethernet cable on another machine and found it OK. Is it possible Ubuntu does not have drivers for this laptop's ethernet connection, or that the laptop is defective?
I'm relatively new to Ubuntu, and have just installed 10.04 on a toshiba portege M100 laptop. Having got over the intel video chipset problems I tried to connect to my WLAN. Network manager would not connect. I tried switching to WPA, WEP and no encryption. No effect I still could not connect. I also noticed that network manager can find other APs much more quickly than mine.Haveing done some searching I tried removing network manager and installed wicd. Was good at finding the AP but reported it as operatingon channel 0. Still would not connect. I tried changing the AP channel to 6, suddenly everyting worked. I switched back to network manager (wicd got in a tangle over hidden networks). Still works.
Having scoured the web for help I found reference to 10.04 kernel suporting US channels. and that I should create a file /etc/modprobe.d/cfg80211, containing "options cfg80211 ieee80211_regdom=EU". I have tried this and it doesnt have any effect. I have noted that there are numerous variants of this advised by different people.Whilst at home I can operate my AP n a US channel, when I am on the move I cannot. I would like to get this working if at all possible.For info the wireless adaptor reported is:
*-network:1
description: Wireless interface
product: PRO/Wireless 2200BG [Calexico2] Network Connection
[code]....
Sorry if this is already posted, but I wasnt sure the right keywords to use the search feature... I am somewhat familiar with older Ubuntu, but recently got 11.04 and installed it on my girlfriends laptop and during installation when it was scanning for the DHCP or whatever it says it failed to find it or something or other and it gave options to do it manually or to do it later so I chose to do it later and after booting into the OS I can not do anything via the internet, not even updates. I have tried looking at the network connections and the only thing there is a wired connection. This laptop accesses the internet through a desktop with Cox cable internet and a wireless router...
View 9 Replies View Related