Ubuntu Networking :: Asus USB-N13 Not Showing As Active But Is Detected
Apr 30, 2010
I recently purchased an Asus USB-N13 and am having some trouble getting it setup. I have followed this post [URL] including downloading the driver version, but I am now a little stuck. This is a laptop which used to have a Netgear Wg111v2 wireless USB adapter (laptop does not have internal wireless). That adapter died so I purchased the Asus. The day I purchased the Asus adapter they were both plugged in at the same time for a short period - not sure if that is relevant or not but just thought I should let you know. Here is some output from various commands:
lspci
Code:
ron@ron-laptop:~$ lspci
00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 21)
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 21)
[code]....
I have restarted a couple of times with it plugged in and with it not plugged. At no time does it show in the Network Manager aplet.
View 9 Replies
ADVERTISEMENT
Feb 5, 2011
Just built a new computer and I think I somehow need to activate my wireless card to get it working.The hardware seems to show up. I get "Wireless Networks" in my network manager but it is grayed out and says disconnected. I think it is an easy fix I just cannot find it.
[Code]...
View 4 Replies
View Related
Dec 16, 2010
I have an asus G73 JW laptop and when I look at all the profiles under material tab, there is not one that includes the .1 of the subwoofer, I have stereo, 4.0 surround but no .1 .... When I play music no boom boom comes out of the sub...
View 9 Replies
View Related
Feb 26, 2010
I am running Firestarter on Ubuntu 9.10 64 bit. I have noticed several times that after closing all web apps (Firefox, Thunderbird) that some entries remain under the heading "Active connections" on the Firestarter "Status" tab. Often these show no source program. Currently I have 2 showing which show Firefox as the source. These persist after Firefox is shut down. I have verified that no Firfox process is running. And both of the IPs point to google.I have Disconnected eht0 and they still show. I have logged out and back in and they still show. I must reboot the machine to make these entries go away. Which makes me think perhaps this is a bug in Firestarter(?) Is there another way I can identify truly active connections?
View 2 Replies
View Related
Mar 3, 2010
Just installed CentOS 5.1 and it's not detecting my NIC. ifconfig produces nothing for eth0. This is a xen kernel.
I can't tell exactly what NIC this motherboard uses, the ASUS website doesn't seem to think we need to know anything more than that it's a PCIe Gigabit lan:
[URL]
lspci indicates it's an Atheros AR8121/AR8113/AR8114.
View 5 Replies
View Related
Mar 16, 2010
I recently installed Arch Linux on an old desktop machine. Everything works well except the onboard audio isn't detected at all.
I am using the 2.6.32-ARCH kernel
My lspci output is:
Code:
# lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] SiS645DX Host & Memory & AGP Controller
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
[Code]....
On another note, the manufacturer (ASUS) actually provides Linux audio drivers for my motherboard (model: P4S533). I attempted to install them, but the configuration process involves using make menuconfig, make xconfig, or make config to add the drivers to the kernel (I think) and I'm still a relatively new Linux user and had no clue what I was doing.
View 14 Replies
View Related
Aug 15, 2011
I have bought Asus K53E laptop, Where it have intel GMA chipest , but when I install compiz on fedora 14 x64 and trying t enable the desktop effect it's not working.Addition to that the screen during the start up showing some waved colours.
Can any one guide me how to install a driver which solving my issue.
Code:
uname -a
2.6.35.13-92.fc14.x86_64 #1 SMP Sat May 21 17:26:25 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux
Fedora release 14 (Laughlin)
Code:
lspci -v
code....
View 1 Replies
View Related
Jul 30, 2015
I've recently installed Debian v8.1 and installed Nvidia driver 340.46. In nvidia-settings I am able to enable my second monitor and enable it/set it's position..etc. My second monitor is not being detected in Debian Display and is 'on' but only showing a black screen. I've tried researching and implementing various 'fixes', but I'm not having any luck.
I'm running dual GTX 570's with a monitor plugged into one each (DVI). I noticed in my xorg.conf under Section "Screen" I have an option "MultiGPU" "Off"; would this be part of the issue?
I've tried:
- purging all nvidia drivers and re-installing
- installing different versions of nvidia drivers
- add nomodeset in grub
View 2 Replies
View Related
Jan 6, 2010
I recently installed Fedora 12 for use with Amahi HDA. Before installing on the Hard drive I used the LIVE CD to test it out. While using the LIVE CD I could see all my HDD's. My file system, my 2nd Hard Drive, and my Raid 0 Configuration. (2 250GB drives) and could browse all my files on those drives.
After installing the full version on my hard drive, my RAID drives are showing up as seperate drives. I have a Asus P4P800 board using hte SATA raid. I know its FAKERaid and not a true hardware raid.
My goal is to restore the Raid in Fedora and make those drives active. However, i dont want to lose any of the data on those drives. To make sure I wasn't an idiot, i rebooted withthe LIVE CD again and verified that I could see the Raid Array.
View 3 Replies
View Related
Mar 11, 2011
how to setup an Active/Active Load Balanced and High Available (If one of the nodes is down the system still runs) MySQL cluster. I have found quite a few howto's but I have some things unclear in my mind. I found a few solutions like this one: [URL] or this: [URK] Those are using two or four MySQL nodes, two Load Balancers to avoid a single point of failure but only one MySQL cluster management server. What happens if the MySQL cluster management fails?
I have also found a "MySQL Master-Master Circular Replication" technique but from what I read, with this option there is a chance that conflicts will arise if node A and node B both insert an auto-incrementing key on the same table.
View 1 Replies
View Related
Dec 26, 2010
I have hesitated posting this because there are a number of threads on the Asus USB N-13.First let me point out that I am using this device.It worked out of the box in Ubuntu 10.10 after several reinstalls using the native Ubuntu driver.However my speed is stuck at 54Mb/s.When tested on a Win7 machine, the connection speed is much closer to 300Mb/s.In wading through the other threads, I am unable to find anyone who has this adaptor running at N speed in Ubuntu 10.10.I have downloaded the latest ASUS driver for LInux but have not installed it as my previous attempts at doing this failed miserably and each time necessitating an OS reinstall.I am an experienced Windows user but a rank newbie when it comes to Ubuntu. The following is the result of iwconfig:chad@linuxbox:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 Ralink STA ESSID:"midgard" Nickname:"RT2870STA"[code]....
View 5 Replies
View Related
Aug 27, 2011
I'm not the greatest with linux in general, I mean I know my way around it okay but theres still a ton to learn, and 11.04 is the first version to work on my custom PC without messing up after I update it so I'm left with natty. Anyway I bought my PC with an Asus U8B-N13 Wireless adapter. The disc it came with has the program to install the drivers in Windows, Mac, and Linux, but the Linux drivers need to be compile and I'm yet to have luck doing so. I've tried to somewhat follow an older guide here: [URL].. but I made it as far as extracting the .tgz, then running the make command and got a couple errors. Here is that attempt:
Code:
dom@NZXT:~$ cd Desktop
dom@NZXT:~/Desktop$ tar -xvzf DPO_RT3070_LinuxSTA_V2.3.0.2_20100422.tgz
DPO_RT3070_LinuxSTA_V2.3.0.2_20100422/
DPO_RT3070_LinuxSTA_V2.3.0.2_20100422/iwpriv_usage.txt
DPO_RT3070_LinuxSTA_V2.3.0.2_20100422/LICENSE ralink-firmware.txt
DPO_RT3070_LinuxSTA_V2.3.0.2_20100422/Makefile
[Code]...
View 9 Replies
View Related
Nov 16, 2010
I have set my Ubuntu 10.04 box with our Windows domain. I can see from "net ads info" that I am on the domain. I can also get the password and group info with getent.So far so good. But I have tried to configure pam basically by following this guide:http://www.ccs.neu.edu/home/battista...nbind/pam.html
Yet when I try to su or login as an AD user I just get and immediate "Unknown id: <userid>".I have had a look at /var/log/auth.log and there are no errors there.Can anyone provide some tips on debugging the pam configuration?
View 1 Replies
View Related
Dec 10, 2010
I have a Realtek nic in my laptop. When i look at additional drivers it says the driver is active but not in use. How do i make it use this driver and always use this driver?
View 1 Replies
View Related
May 5, 2010
I have a Asus N13-usb adapter and i am running ubuntu 10.04 on my desktop. I tried all those commands that you have posted but it led me nowhere. I was wondering if you can help me start off from scratch. I have typed lsub and it showed the device. I followed this thread [URL]and i did it up the part where you downloaded the driver. but i was not able to go further once i typed in the command :
cd Downloads
tar -xvzf
View 9 Replies
View Related
Nov 4, 2010
I have an Asus EEE PC 901 from a few years ago with an integrated wireless card (touted as the "integrated Intel Wireless Wi-Fi Link 4965 AGN LAN chip" on the website). I am running Ubuntu's Desktop remix 10.10.
My computer connects fine to any given wireless network the first time around, but will not connect to it again.
After I disconnect from a network, every time I try to connect again, it continually asks for the password, and never fully connects, but will spend about 20 minutes trying and asking for the password and trying again.
Sometimes, it will say it is connected (100% strength) but will never load the google start page. This will last about 2 minutes, then it will disconnect, and start the never-ending connection process again.
View 6 Replies
View Related
Dec 5, 2010
Chili555 where are you?
I am running Ubuntu Release 10.04 (lucid), Kernel Linux 2.6.32-26-generic-pae, GNOME 2.30.2.
I have installed the ASUS USB-N13 according to your advice in previous posts, specifically, in your advice to 828688 Ben.
The dongle seems to be operating as it should. The LED does its flashing at what appears to be the correct time. Wicd also looks correct. Networks are found with good signals shown. Everything looks correct. But when I attempt to connect, "validating authentication" runs for quite some time, and eventually results in a dialogue window stating the communication failed. The required WEP password is entered in the RT2870STA.dat file, and again in the wicd window.
I have entered as much detail in the RT2870STA.dat file as I dare, and believe it to be correct.
ndiswrapper is not installed. Network Manager is uninstalled. Only wicd remains.
View 9 Replies
View Related
Jun 16, 2011
I've been debugging for a few days and can't get this to work.
I've tried all of the following suggestions:
[URL]
Some possibly relevant command line output:
Code:
$ sudo ifconfig
eth1 Link encap:Ethernet HWaddr bc:ae:c5:68:8b:a2
inet addr:10.42.43.99 Bcast:10.42.43.255 Mask:255.255.255.0
inet6 addr: fe80::beae:c5ff:fe68:8ba2/64 Scope:Link
[Code].....
(I'm connected to an ethernet port which connects to my laptop which grabs the wireless, currently.)
View 4 Replies
View Related
Jul 26, 2011
I recently purchased an Asus n10 wireless usb adapter to use with my media server, running Ubuntu 10.04 LTS (Lucid Lynx). After spending several hours today with many of the threads (especially this one about the Asus n13) it seems that I've run out of ideas.
My network is running a hidden (non-broadcast) SSID ("Potato") with wpa2 personal encryption.
Here is the relevant information from lsusb:
Code:
Bus 001 Device 003: ID 0b05:1786 ASUSTek Computer Inc.
Iwconfig follows. The rest of the values, like link quality & etc, are all zero:
Code:
wlan0 802.11b/g ESSID:"Potato"
Mode: Managed Access Point: Not-Associated Bit Rate: 0kb/s
And the kicker is that the interface doesn't seem to be available, despite the above reports. ifconfig wlan0 up produces:
Code:
SIOCSIFFLAGS: Resource temporarily unavailable
View 9 Replies
View Related
Jul 27, 2011
I recently bought an Asus laptop and had a friend install ubuntu 10.04. After the install was complete I tried to connect to a network and there was no networks available. After some research time my friend said the I need network drivers to install in ubuntu.
View 8 Replies
View Related
Feb 24, 2010
I am running the Ubuntu Netbook Remix and setting up our systems for Active Directory Domain Authentication. When I am hard wired in (ethernet), AD authentication works with no problems using the Likewise-Open software (installed through Ubuntu Software Center). What I want to be able to do is have people authenticate with AD with only a wireless connection. Has anybody done this before?
View 1 Replies
View Related
Oct 16, 2010
After trying to make audio output work on Lenovo b560 notebook I finally succeeded but the wireless stopped working. The driver was removed. I tried to follow the instructions from Broadcom http://www.broadcom.com/docs/linux_sta/README.txt and it started showing the driver in admin - drivers, it shows that it is activated but not in use, but once I get to this point
"modprobe wl"
it shows this:
install /sbin/modprobe --ignore-install wl
insmod /lib/modules/2.6.32-25-generic-pae/updates/dkms/wl.ko
FATAL: Error inserting wl (/lib/modules/2.6.32-25-generic-pae/updates/dkms/wl.ko): Unknown symbol in module, or unknown parameter (see dmesg)
[Code]...
View 3 Replies
View Related
Sep 20, 2010
I have a 2 node Oracle cluster running on RHEL 5.4. One server went down the other day, and then restarted. Virtual IP address switched to the other node as it should, but did not switch back where the failed node came up - problem is the ip address is still on node 2, but I cannot see it or down the interface as it does not show up with ifconfig -a. I would expect to see it on eth0:2 but only eth0:1 is showing up with the correct vip for the node. ifconfig -a on node 1 shows n vip configured. I can telnet to this ip address and login, so know it is still on node 2, so why can't ifconfig -a show it, which interface is it on, and how do I remove it so I can get it back on node 1
View 1 Replies
View Related
Jan 6, 2010
I've read through 99% of the other "kismet config" help threads, and can't find with this.lshw -C network output
Code:
*-network
description: Wireless interface
[code]....
View 8 Replies
View Related
Mar 21, 2010
Im a newb to ubuntu just wiped my brand new asus 1001p netbook of windwos 7 and put ubuntu netbook remix on it 9.10....Everything works great except the wireless...I know theres probally a billion topics on this, but i just need step by step easdy to follow guide on how to do this...I asked the IT at my work and he claims it cant be done, unless i switch out the internal wireless to a card that "just works", which im not comfortable with or use a usb wireless stick, which defeats the purpose of a netbook being so small....Im sure this can be done so please help me show up a IT that doesnt know linux .BTW the wireless card is a atheros thats all i know..
View 8 Replies
View Related
Apr 16, 2010
I just installed Ubuntu lucid beta2, but I'm having no luck getting my wireless card (Asus WL-103b cardbus) to work. It uses the b43legacy driver. I have also installed the correct firmware. This card used to work if I'm not mistaken.
[ 267.239150] pcmcia_socket pcmcia_socket1: pccard: CardBus card inserted into slot 1
[ 267.239267] pci 0000:06:00.0: reg 10 32bit mmio: [0x000000-0x001fff]
[ 267.239384] pci 0000:06:00.0: supports D1 D2
[ 267.239401] pci 0000:06:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 267.239421] pci 0000:06:00.0: PME# disabled
[Code]...
View 2 Replies
View Related
Sep 18, 2010
I've bought a Asus EEEpc 1005 PX and trired to install Ubuntu netbook. But I found that wifi is not working. It's not detecting the wifi cards.I tried ifconfig, and it is showing me,When I tried LSPCI it's showing me
Ethernet controller: Atheros Communications Atheros AR8132/L1c Gigabit ethernet adapter (rev c0)
Network Controller: Atheros Communication inc. Device 002c (rev 01)
how can i set up the wifi here.(I tried with Meego, and Meego detected the wireless autometically..But I want to use Ubuntu)
View 8 Replies
View Related
Oct 3, 2010
Just purchased a Asus USB-N13, and having follwed a mixture of tutorials, including the readme on the driver disk, i have had no luck in getting this adapter to work.Upon using "sudo iwlist ra0 scan" the adapter can see multiple networks, however device manager is stating that the device is not managed. How can I get this sorted and connect to a network?
View 1 Replies
View Related
Oct 17, 2010
i installed ubuntu on my netbook after having a successful install on my asus g51 laptop.
everything works fine except the wireless. for some reason the netbook wont pick up internet via the ethernet connection so i went and got the drivers via synaptic and copied the packages plus the dependencies required (just needed one - dkms). dkms installed fine, but there was an error when i tried to install bcmwl-kernel-source. ubuntu still sees it as installed tho looking in ubuntu software center.
i rebooted just for shits and giggles, cuz it still didnt work. no dice. then i tried to check in that section that shows drivers that arent allowed in a default install as per another thread. its not in there.
my situation doesnt let me connect this netbook via wire and the only way i can get software for it is to download it via my ubuntu connection on my laptop.
View 9 Replies
View Related
Nov 27, 2010
I need some help getting my wireless card working.I have a ASUS PCE-N13 and I'm running ubuntu 10.10 AMD64.I have confirmed that the card works running under win xp.The problem I have is that it can't see any available networks.I have downloaded and compile the latest driver from ASUS rt2860sta 2.1.0.0 and added these lines to the blacklist file.
blacklist rt2800pci
blacklist rt2800usb
blacklist rt2x00lib[code]...........
View 1 Replies
View Related
