I recently purchased the Linksys AE1000 wireless USB network adapter. After some struggles, I found and installed the Ralink_RT3572USB_drv2400 driver for it and it now works, however it won't turn on when I boot up the computer. I have to manually unplug and then plug the adapter back in for it to work again. I followed the instructions on this how to for installing the driver.
[URL]
Here is the situation: I am currently running Ubuntu 10.10 64 bit. I'm trying to get my Linksys AE1000 to run correctly. I have followed many tutorials but most notably was:[URL].. lsmod shows that rt3572sta is loaded. network manager in gnome is able to find my router. my problem occurs when it tries to connect to the router using wpa2 security. It continually asks for the wireless password then will freeze the system after a number of attempts. After digging in for a bit, I was able to dig out a dmesg trapping the error:
BUG: unable to handle kernel paging request at ffffcfb0138af1ec
IP: [<ffffffffa021c7e8>] Cntl0idRTBssidProc+0x78/0x570 [rt3572sta]
PGD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/cpu7/cache/index2/shared_cpu_map
CPU 2
I really don't see the need to continue on with those error messages lsmod still shows rt3572sta after the failure. In case anyone wants to see the changes I have made to the files before the make, I have included them. but changed the extension to "txt" to accommodate the up-loader and my rt_linux is too big to fit here, just not that it was 2 lines that were changed to work with the kernel. If anyone wants to know what I mean by the system freezes, I do mean just that. The mouse will continue to work, but I am then unable to open any programs, unable to reboot the computer. it requires a hard reset.
I have uninstalled the drivers, installed them, make them, make install them, make clean, start from scratch a few times, and am getting no give here.
I have a AE1000 wireless adapter and Ive been using it or about 4 months on windows xp. Yesterday I installed ubuntu 10.10 and it won't work It won't connect to the internet and won't even show signs that it is turned on.
View 5 Replies View RelatedOk so I tried to follow the directions here: [URL] However, I couldn't find 2010_0915_RT3572_Linux_STA_v2.4.0.2.tar.bz2. Instead, the closest I could find was 2011_0407_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2 .5.0.2_DPO.bz2, so I tried it. I edited config.mk and rtusb_dev_id.c as chili555 advised. I tried to edit linux_rt.h, however, the only file I saw was rt_linux.h. I edited it according to chili555's post, message #7. I went back to the root directory of the extracted .bz2 file and did
[Code]...
The linksys AE1000 is not supported by linux according to the linksys website. Are there any workarounds? I use this network adapter to connect to my wireless network, and it is basically useless at the moment.
View 6 Replies View RelatedI have managed to compile and install the driver for my linksys AE1000 adapter. I can scan and see my network (and several others) but can't seem to connect. I have read a few threads looking for clues but I can't seem to figure it out. My kernel is 2.6.35-24-generic and I am using the latest rt3572 driver (v2.5.0.0). Here are a couple of steps that I have taken:
1) The usb driver does work properly and connect on a Windows machine.
2) Temporarily removed security from my router (uses WPA2). Still can't connect.
3) Tried compiling and installing the previous version of the driver (2.4.0.2)
Alright yall, I just got my wireless usb device to work on ubuntu 10.10. I did alot of searching and I finally figured it out. this is what I did.
1.Download the linux drivers from this post, its called Ralink_RT3572USB_drv2400.zip
2.Extract them to a directory.
3.Make sure you have build-essential installed on your computer. you can do this by opening a terminal
and typing
Code:
sudo apt-get install build-essential
4.Now install linux headers so that you can compile the drivers.
Code:
sudo apt-get install linux-headers-$(uname -r)
5.Now in your terminal goto where you extracted the Ralink_RT3572USB_drv2400 files.
once in that directory type
[Code]...
for my small home server i want the machine to NOT start x11 automatically but to enable remote logins via xdmcp.The problem: xdmcp is controlled by gdm. If i disable gdm to have no x11-login-screen xdmcp does not run...Is there any way to start gdm without starting x11 on the console?
View 2 Replies View RelatedWell my friend just gave me a Cd so i could switch back to windows vista but when i run with starting cd rom and i press any key to start cd or dvd it goes black with a blinking thing on the top left corner i went to sleep for 2 hours hoping it would be done when i get back but it was still there
View 1 Replies View RelatedI installed and configured privoxy - everything worked nicely when I run it manually by
Quote:
/etc/init.d/privoxy start
After restarting the computer privoxy wasn't start automatically. I checked the links in /etc/rcX.d - are o.k. I installed sysv-rc-conf - shows that for runlevel 2 - 5 privoxy is running. I changed /etc/rc2.d/S20privoxy to /etc/rc2.d/S99privoxy - to start that process at the end. I installed Boot-Up Manager. Privoxy is marked for start automatically. I added in /etc/rc.local line: /etc/init.d/privoxy start
Privoxy still doesn't turn on at boot time and every time I must start it manually. Could you tell me how could I repair this ?
I have a problem with 'Starting File Manager' completeley filling my taskbar on startup.There could be 100 of them for all I know, as the taskbar ends up dividing into tiny slices for each.How do I find out what is causing this? Is there a log file I can check or some way to repair ubuntu off the Live CD?Recently installed some updates. Last night tried reinstalling Nautilus and Gnome (did that with commands from Ctrl Alt F1 ) but that has not helped.I'm running Ubuntu 10.04 LTS (64bit)Dell Inspiron 530I'm no Ubuntu / Linux expert, but I can try to find any info / logs required
View 1 Replies View RelatedI'm trying to connect to a friend's Linksys WAG160N router using Ubuntu 10.10, but it's just refusing to connect. I can connect to other wireless networks fine - it seems to just be this router. The wireless indicator applet thing shows that I'm trying to connect, but the password box always just pops up again and again. I'm certain I've got the password correct and am able to connect under OSX on the same computer. Connecting to it via ethernet also works fine.
View 1 Replies View RelatedUbuntu 10.04 not seeing my WUSB300N. What is the Easiest way to get this working?
View 1 Replies View Relatedi have installed mysql and its running fine. how i can stop mysql from auto starting when i start my machine
View 2 Replies View RelatedI have loaded ubuntu 9.10, and am not getting internet from my router using a linksys EG1032. I have found articles stating that i should use the sk (URL...) or nge URL...)drivers. According to the instructions i found, they require that i make changes to my kernel config. I do not know how to do that, or if doing so is wise.If someone would help me figure out how to connect this NIC card.
View 7 Replies View RelatedMy first Ubuntu/Mythbuntu install. Installed OS, plugged in linksys wireless G adapter. It finds the network but cannot connect. Discovered wireless priviledges while setting up admin/user accounts. Should be ready to go. or not, I'm thinking it needs a driver but
1) in linux? certainly not in Fedora.
2) If it can see the network it doesn't need a driver,
My settings are wrong or I'm missing something. SSID is set in settings. Do I need mac address and BSSID?
I just installed Ubuntu 10.04 on my formerly XP system, and I'm trying to get my wireless network working. I have a Linksys WUSB11 v2.6 wireless adapter connected by USB to the system.
The system networking icon reports "No wired networks".
I'm not sure whether or not the system sees the USB ports... If so, it apparently doesn't recognize the adapter.
I saw a few posts that indicated that this adapter didn't work on 10.04 but it had worked on 9.04.
I'm looking for any info to get this working, including any or all of the following:
* How to determine if the system sees the USB ports (or is it "obvious" that it does)
* Should the wireless adapter work just by plugging it in?
* How to troubleshoot the networking adapter to get it working
* (If downgrading to 9.04 is likely to solve the problem) how to downgrade to 9.04 from 10.04...
The Linksys USB Wifi Adapter (WUSB11 v2. does not work with UBUNTU.
I am using UBUNTU DESKTOP 64-bit (x86_64) 10.04, but I think it is not working in the 32-bit version as well.
I really love to get my Ubuntu work with my 64-bit hardware....
Previously I had my desktop hooked up to a nearby router via an ethernet cord with my parents' computer having a wireless usb adapter to connect (This thing: [uRL]). We just moved and our setup has reversed (router is near their computer, I am using the usb adapter). I just installed the latest Ubuntu and now I can't get the usb adapter to work. I'm very new to Linux and I have no idea what to do. I think this is the same usb adapter.
View 1 Replies View RelatedI just bought Linksys WAG160N ADSL 2+ Router and modem device. It came with an setup installation CD which is not running on ubuntu. In the manual it is written that it will run only under windows and Mac OS. I have only Ubuntu on my laptop.
I need to run the setup CD to go ahead. I searched more than three hours to find out how to run this CD so that I can complete the setup of my new modem-router but did not find any solution.
My old ubuntu laptop beeps 3 time on startup and then freezes. This forced me to install 10.04 on a new laptop. Now I can't get the linksys wpc54gs ver 2 to get connect. I can see the router with a padlock by it. I pretty sure I have the correct password in the right spot. I can access the internet with the wire connection. I'm sure it something simple I forgot from before when the card was working in the old laptop.
View 2 Replies View RelatedI think lightning may have killed it. It was working fine. Now I cant get it recognized no matter what I do. It also quit working in Win XP where I never had a problem with it because it had its own connection software.
dmesg yields this-
RTUSB disconnect successfully
[ 312.876034] usb 2-1: new full speed USB device using uhci_hcd and address 7
[ 312.996021] usb 2-1: device descriptor read/64, error -71
[ 313.220031] usb 2-1: device descriptor read/64, error -71
[ 313.436038] usb 2-1: new full speed USB device using uhci_hcd and address 8
[ 313.556025] usb 2-1: device descriptor read/64, error -71
[ 313.780031] usb 2-1: device descriptor read/64, error -71
[ 313.996032] usb 2-1: new full speed USB device using uhci_hcd and address 9
[ 314.404022] usb 2-1: device not accepting address 9, error -71
[ 314.516021] usb 2-1: new full speed USB device using uhci_hcd and address 10
[ 314.924029] usb 2-1: device not accepting address 10, error -71
[ 314.924046] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 343.664017] pan0: no IPv6 routers present
[ 809.024049] usb 1-1: new high speed USB device using ehci_hcd and address 10
[ 809.182271] usb 1-1: configuration #1 chosen from 1 choice
[ 809.182837]
[ 809.182839]
[ 809.182840] === pAd = ffffc20020b41000, size = 598568 ===
[ 809.182841]
[ 809.182845] <-- RTMPAllocAdapterBlock, Status=0
guest3@guest3-desktop:~$
I have a linksys wireless-b wmp11 network card. Can anyone tell me how to get this up and running? Maverick is up to date as of yesterday and I have the cd that came with the card. I have no way to access the internet on the machine. I am typing this from my laptop.
View 2 Replies View RelatedI am dual booting XP and Ubuntu 10.10 64bit on a Dell Latitude E6410 and I have a Linksys WRT120N router connected to my Modem.
So the weird thing is, under XP I can use the internet while connected to my router. Under Ubuntu I can't use the internet while connected to my router. But I can use the internet in Ubuntu if I connect to my neighbor's router called "linksys". So something happens when I connect to my router that makes Ubuntu not able to access the internet. But if I'm connected to my Neighbors router or if I use XP while connected to my router I can use the internet.
I have been using Ubuntu for about a year, so I'm getting better but still a noob. I've tried to figure out what's going on by looking at other forums and posts and trying to see if anyone has solved this. So far I've had no luck. This is also the first of many problem I have encountered that I have been unable to solve using online posts, and is the first problem that I have had to resorted to creating a post to try and fix.
I connect to multiple wireless system each day but when I encounter a Linksys-n router the computer will recognize it and connect but does not go online.
Does this give any clue for why it will not connect?
Code:
802.11a/b/g
System wireless is: Toshiba Satellite M115-S3094 with Intel PRO/Wireless 3945ABG (802.11a/b/g), Ubuntu 10.04
I have a linksys wusb100 and need to set it up on ubuntu 8.04 and 9.10.
View 4 Replies View RelatedI am net to this whole Linux thing. I cant seem to connect to my Linksys router. Not sure if I have to call Linksys or what.Mine is a WRT54GS
View 1 Replies View RelatedWhen trying to start KMail it attempts to start Akanodi, this fails and so does KMail.
The only solutions I could find are here: Akonadi 4.4/Troubleshooting - KDE UserBase
These did not work
--
Akonadi Server Self-Test Report:
Test 9: ERROR
--------
Akonadi control process not registered at D-Bus.
[Code].....
The nfs-client service isn't starting after boot up. This is causing problems with the user as they cannot access the remote folders on the server. The PC is a Thinkpad X60s with oS11.3 and KDE4.4.4. The problem started about a week ago after some updates (new kernel update, kde4 updates and some system files) were applied on the laptop.
After logging in none of the remote folders are available. Checking the nfs-client service under Yast>System Services (Runlevel) shows the nfs-client service is not running. If I enable and start the service I get the pop-up confirming the service has started but still cannot access the remote folders even after issuing a mount -a. Opening Dolphin just opens a blank grey window which needs to be terminated.
Trying to restart the nfs service using su -c 'rcnfs restart' sticks at Starting NFS client services: sm-notify Just leaving the PC for 10-15mins eventually sorts itself out and the remote folders become visible. I cannot see anything obvious in the logs so am a bit stumped.
kde knetworkmanager is not starting on startup.i am starting this manually every time on login to connect to network..how to make it start automatically?
View 9 Replies View Related