I have two Ubuntu 11.04 machines connected via cable to the same D link ADSL router. how do i connect one to the other so i can see from the other computer files and transfer them using nautilus?
View 9 Replies- CAN connect to other computers - ssh and vnc over the home network (via D-link 524 router).
- CAN get an IP address via DHCP
- CANNOT get internet connections - including router at 192.168.0.1
- CANNOT even ping router (but I get an IP address - weird)
- Other computers on the network CAN access internet
- Live CD could not access internet
results of ifconfig
Code:
Code:
I am wondering if his ISP could be doing this - he has received a warning letter about bitorrent. Could the isolate a single computer behind a NAT router?
This is the results from dmesg:
Code:
I have tried:
- to set proxy settings as "Direct internet connection"
- disconnecting power to (including 30 sec wait): modem, router, computer + unplugging ethernet from computer
- Live CD (he only had an old one 7.10) which also didn't connect to internet, but as I am remote, I couldn't do any more. We are downloading a 10.04.1 iso for him to burn tomorrow, and will try that again.
- Uninstalled Crashplan which was the last software that we installed (and it was working ok).
I am currently ssh'ing into another computer on the network that IS working, and then ssh'ing into my Dad's computer - including a VNC session (tunneled through both machines and router).
If I have a desktop with a USB wifi adapter connected to the internet through an ethernet cable, is it possible to create a wireless network using the adapter that will allow other users to connect to the internet through mine? I'm in a fairly low-tech place for the next few weeks and getting a router isn't likely.
If it's possible, anyone have links or instructions for how to do it?
I have built a linux router with a pc having two network cards. I am running ubuntu 8.10.
I have enabled forwarding on the router. One network (192.168.1.0/24)is connected to eth0 and another (192.168.2.0/24) is connected to eth1.
The interfaces have addresses 192.168.1.1 and 192.168.2.1.
On any side side of the network, I can ping both interfaces on the router.
However when I ping a machine on the other side of the network, I get 100% packet loss.
I have not touched iptables on the router or any machines.
What I am doing wrong?
I have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
net.ipv4.ip_forward=1
Then I tried this on the laptop:
sudo iptables --table nat --append POSTROUTING --out-interface ath0 -j MASQUERADE
sudo iptables --append FORWARD --in-interface eth0 -j ACCEPT
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
I want to be able to access my desktop from work so I first set up a DNS. I can ssh into my own computer and using the ip address but when I try to ssh using my DNS (this is from my home wireless which is Linksys E2000), I get the following error:
debug1: Reading configuration data /etc/ssh/ssh_config
debug1: Applying options for *
debug1: Connecting to ****.com [74.79.145.28] port 50000
debug1: Connection established.
debug1: identity file /home/andy/.ssh/id_rsa type -1
[Code].....
I set up the settings on the Linksys to accept DDNS but I am thinking there might be something else I overlooked? I do not understand completely what is happening to debug this. It seems like it initially accepts the connection and then something strange occurs.
I am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
[Code]....
I have 2 computers,one is connected directly to internet with a classic rj45 cable. it has a usb wireless dongle too (ralink)the second has a usb wireless dongle but no network card.is it possible to connect the second computer to internet through the first? (second computer connect to the first computer through wireless and through it to internet)infact in first computer share internet with usb dongle.
View 1 Replies View RelatedI am using Fedora 11 all upgrades, wireless network WUSB54G network adapter. I can get to the internet but cannot get to any Windows (192.168.1.100) or Fedora 11 (...104) computers, printer (....101, 105). Here are the tests I have run.
[root@Fedora2 sbin]# ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.76 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=268 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.63 ms
^C
--- 192.168.1.1 ping statistics ---
I tried to connect two ubuntu computers via crossover network. But sometimes they can connect and see each other and even ping each other and sometimes not!
Each time, each of my PC's can ping it's own IP address but may not ping the other PC. I tried to disconnect cable, reconnect, disable network, enable it again, change IP address, disconnect via Network Manager Applet, reconnect and... . But when one of them don't want to connect I can't do this anyway!
Anyone knows what must be the problem? Sometimes it took about many seconds to get them connected, and sometimes they can't connect for many hours.
I must add that I have an ADSL modem on one of two Ubuntu PCs that connect via another cable.
My son lost his USB Wireless stick for his Computer. I had thought I heard that if you had a second wireless router, you could use it somehow to detect the wireless router you have already set up in your home (like using a wireless card)? Is this what Ad-Hoc is? Either way, can this be done and if so how? I use a WRT54Gx2 Lynksys router and have a TRENDNET TEW-432BRP wireless router and also a spare D-link DI-514. I use ubuntu 10.04, and also wanted to know if I connected one of the router to his on the LAn port could he connect msaybe through an Ad-Hoc on my local computer here? He uses XP on his. I'm a newbie to linux and networking in general.
View 2 Replies View RelatedI have 2 10.04 computers and one win 7 and one vista computer: The win computers can see each other and the ubuntu computers, but the ubuntu computers cannot see each other or the win machines. The ubuntu computers connect to the internet fine and can ping each other. I cannot find settings to correct.
View 3 Replies View RelatedMy problem is little different then what I've seen here. I get the same message after inputting network name and password. I click connect and it just pops up again I don't get it. I'm running Ubuntu 8.10 for Ppc (PS3) I get no internet connection what so ever just the same message. The message I get is " authentication required by wireless network " What do I need to do to connect wireless to my router with my PS3 using Ubuntu 8.10? It does connect with a Ethernet Wire. I am new with Linux.
View 1 Replies View RelatedI have a router with 2 IBM Thinkpads connected. One Thinkpad is running Ubuntu, and the other is running XP.
They connect to the router with no problems.
I installed Ubuntu on a Sharp Moebius laptop and plugged in the network cable.
NOTHING.
I have tried pinging the laptop; nothing.
I am not sure where the problem is, because my Thinkpads have no problems connecting to the router, with both Ubuntu and XP
my LAN just suddenly stopped working. we had a power outage, and it just stopped. it will still recognize the network, but it wont connect. i was experimenting with setting up a web server (trying to set it up on the standard distro). i know its not the network card (on board) because i can put in my pci card and it still wont connect. it will connect when in the live environment. i thought that maybe it had updated, so i tried to boot from a different (older) kernel. that still didn't help.
i stopped apache. i was experimenting with portforwarding at the time (i had everything else working on my server), but i could not get it to work. after this happened, i restored the original settings on my router. i had applied the settings only a day before the power outage. everything still works on another computer on the network (also running linux). (all computers run 9.10) its almost like my router won't assign me an ip address.
I have a new belkin N1 router which I tested in somebody else's flat. It worked fine. When I got home I reset it by pushing a paperclip in the hole for 10+ seconds to erase this flat's internet connection settings (username and password and stuff). After this I plugged it the computer and tried to connect to it (wired connection) using 192.168.2.1 (this is correct for that router, it is not 192.168.0.1). But the browser says it is offline and cannot connect. The lights of the router cycle, the "modem router" light blinks continuously and the others briefly come on and go off again, every few seconds. I tried resetting it again, several times, leaving it off for a few hours, leaving it on for a few hours, etc.
View 2 Replies View RelatedI recently just upgraded my operating system to Ubuntu 10.04 LTS and I can't seem to get my wireless card to connect to our new Verizon Actiontec router. I am using an Encore Electronics 802.11n Wireless USB Adapter (model: ENUWI-N), which had worked with an earlier version of Ubuntu and our old router. The adapter recognizes the SSID of the new router but will not connect with the correct WEP key or even with the encryption turned off. I have tried deleting the wireless profiles and manually re-creating them and still no dice. I have also gone to the website of the chipset manufacturer and found the latest drivers (RT2870USB(RT2870/RT2770)) for the adapter, which, according to the Synaptic Package Manager, I do not currently have installed.
Where do I go from here? Do I need to install the new drivers, and if so how do I do that?
I wanted to try Ubuntu again but have gone wayback to an old 8.10 disk because I couldn't get 10.10 to work. The install with 8.10 went fine but the internet will not connect. The network manager shows eth0 grayed out and when going in to manage the connection it says 'never'. I'm using Vista with a broadband modem connected to a netgear router.
View 3 Replies View RelatedIm trying to setup Ubuntu for my buddy. After talking it up for ages of course i get a problem ive never seen be for . He is running 10.10 (or whatever the newest is lol) and when running windows it hooks up to the internet just fine through the router. however in ubuntu it will only connect when i plug it directly into the modem. Route gives no output. Kinda weird. router is Linksys Wireless G Broadband Router. WRT54G.I dont want him running back to windows before he even gets into it.
View 4 Replies View Relatednew to ubuntu and having difficultly connecting to my wireless router.It can see the router but will not connect keeps asking for password.usb adapter is working 100% as i can connect with it using xp 64bit.
View 4 Replies View RelatedIt says my routor's name and signal strength but when I try to connect it tries for a while and then fails.
View 1 Replies View RelatedI think I have unique problem. I have a d-link DWL G510 rev c.(Austrailian) WiFi card in my pc which is detected as
Quote:
Network controller [0280]: RaLink RT2561/RT61 rev B 802.11g [1814:0302] in lspci -nn.
iwconfig shows:
Quote:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=6 dBm
Retry long limit:7 RTS thrff Fragment thrff
Power Managementff
ppp0 no wireless extensions.
Now sometimes it detects my wifi router and shows its ssid in nm-applet. but when I try to connect, it tries for 3 or 4 minutes and then fails. for most of time it even does not finds my router.
I have installed ubuntu 10.10 and am really happy. I want to sort the wireless conection out now. I have been through this forum for hours today and can't get it working. I have a Broadcom wireless card, which seems to be working fine, but I am not 100% convinced.I have attached the output of some of the commands that I have seen referred to on here.
I am using the wired connection on the same router, so the router connects fine.I click on the network icon and I see the skyNNNN router in the list. I have tried connecting to it and it asks me for my password, which I provide then nothing happens until it asks me again.I have removed the security from the router and I then see the same skyNNNN router without a
lock icon. I try to connect and it still fails.I am not using an access list on the router, so there is no issue with the mac address.
I have been using pppoe connect to Internet,now I want my notebook get on line,I bought a wireless router but Ubuntu(64-bite) can't connect to Internet through the wireless router.pppoeconf said that found eth0 and vboxnet0,but search concentrator failed and pppoeconf exited.How can I fix it.
View 1 Replies View RelatedI'm running Ubuntu 10.04LTS 64bit. The desktop running it does not connect to my router or the internet. My mac laptop does. When I installed windows on this desktop, it too could connect. But after reinstalling ubuntu, I cannot. I tried upgrading to the latest ubuntu, but that just bricks my computer. Here is my ifconfig:
Code:
~$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:1d:09:95:39:76
inet6 addr: fe80::21d:9ff:fe95:3976/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1492 Metric:1
[Code]....
I have just installed 11.04 alongside windows vista. I have been trying to connect my router but it keeps saying disconnected from network. I have ran all of the troubleshooting tips in ubuntu its self and everthing seems in order. is there any settings i need to change on my router or in ubuntu's edit connections programe? I managed to connect to the router once to upgrade from 10.10 to the 11.04 but even before upgrading to 11.04 i had problems connecting to the router.
View 6 Replies View RelatedI'm having a problem with my RTL8187 wireless card using NDISwrapper The problem is that I can't connect to my home router I tried everything and it won't let me Suggesting changing my security settings to WPA is not valid because my retarded brother won't let me do it, so is there anyway I can connect to this router??
View 1 Replies View RelatedJust installed ubunto 1104 and I cannot connect wirelesly to my router. When I go through the trouble shooting the recommendation is to got to the device drivers page but the link does not take me anywhere. Here is the info from the terminal.
*-network DISABLED
description: Wireless interface
product: AR9287 Wireless Network Adapter (PCI-Express)
vendor: Atheros Communications Inc.
[Code]....
I'm trying to connect to a new Belkin wireless router, but wicd refuses to connect. I've been reading some of the other threads but they haven't made much sense as the hardware is different.
The output from the iwconfig command is as follows:
When I ran lspci it told me I had a RaLink RT2800 802.11n PCI Network Controller. On the box it says it "Supports the most popular systems" and mentions Linux. I'm using a 63 character WPA2 password, which has been copied from a USB key, so I know that is correct.
I am net to this whole Linux thing. I cant seem to connect to my Linksys router. Not sure if I have to call Linksys or what.Mine is a WRT54GS
View 1 Replies View Related