I have done a scratch install of Ubuntu 11.04 (Natty) successfully today. I am facing problem while adjusting my monitor resolution.
My motherboard is pretty old, Kobian 845GLNDSMx. When I tried to adjust the resolution from Preferences -> Monitors, the resolution is shown as 800x600 (4:3), Refresh Rate - 0Hz and Rotaion as normal. "Monitor Unknown" is highlighted on the window. Moreover, "Detect Monitors" doesn't work.
I have never used Linux always windows so heres the problem the display only has 2 settings 640x480 and a smaller one and it say unknown monitor. I installed the drivers in hardware driver in systems I'm running Ubuntu v 9.10 if that matters and the video card is a Nvida mx440.
I am new to Ubuntu. I installed Ubuntu 8.04 and it detected my Acer monitor AL1716 correctly and it works fine. However when I installed Ubuntu 11.04 it shows the monitor as " Unknown Monitor" and the maximum resolution is 1024x768 and I cannot set the native resolution which is much higher. My motherboard has Intel 845G chipset and built in graphics. I tried Ubuntu Software Center, but couldnot solve the problem.
I am facing problem with the fresh installation of Fedora 11. (I have moved from Fedora 9). When I try to view videos on ..... or use the Cheese Webcam Booth, I get blurred lines on the screen and I am unable to see any video or pic.
Also I noticed that the when i go to System > Preferences>Display, it shows me UNKOWN MONIOR.
However, if I got to System>Administration>Display and enter the su password, it shows me correct monitor and the graphics driver.
I am not sure if my original is related to the Unknown Monitor.
I also tried to install Nvidia driver but it crashed the xserver and I had remove the driver.
My Monitor is LG 700E and Graphics card is from intel. as I am not able watch any video.
I'm trying to upgrade my sister to natty, but it wont boot properly unless I use nomodeset. It didn't need this in maverick, and she doesn't need any proprietary drivers, as she only has onboard laptop graphics (intel mobile 4 series I think..) So when I boot it into the LiveCD the resolution is wrong, so I go into system > preferences > monitors but it wont let me change the resolution as the monitor is listed as "Unknown" I also tried LinuxMint 11 (Katya) but it was the same (it is based on ubuntu anyways so it's not surprising.)
I have an acer aspire one netbook and in display properties it says the monitor is unknown. The trouble is that the screen is widescreen (16:9) but it has it as (4:3)so the screen is sort of stretched. Is the a terminal command as another way round this or how can i get the screen recognised?
I have a nVidia GeForce GTX 760 Ti Graphics card. I have installed the proprietary driver and disabled the open source one. The problem is when I connect to two monitors via DVI and VGA, the VGA one appears to be 'unknown' and is using incorrect resolution of 640x480. How can I correct its resolution?
The xrandr output
Screen 0: minimum 8 x 8, current 2560 x 1080, maximum 16384 x 16384 DVI-I-0 connected 640x480+0+181 (normal left inverted right x axis y axis) 0mm x 0mm 640x480 59.9*+ 320x240 120.1 DVI-D-0 connected 1920x1080+640+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.0*+ 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x720 60.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 640x480 75.0 72.8 59.9 HDMI-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 disconnected (normal left inverted right x axis y axis)
I've just installed OpenSUSE 11.2 on a new machine. Because I was still using another machine as my main box while building the new one, the monitor attached when it was installed has a resolution of 1280x1024 @ 77Hz. I've now moved it to be my main machine and the monitor is a widescreen 1680x1050 @ 60Hz model. When I boot it normally the screen fails to come up - even GDM doesn't show. If I boot in failsafe mode the system comes up fine, but in 1280x1024 mode. The 'Configure display settings' icon shows the monitor as 'Unknown'. Couple of things I tried:
1) Switched to runlevel 2 and logged in as root. Ran Xorg -configure and looked at the xorg.conf.new that was installed, but it just had generic info for the monitor:
[code]....
2) While still in runlevel 2 and logged in as root I did a startx. This brought up the X display in 1680x1050 ok, and clicking on the 'Configure display settings' icon showed it had correctly identified my monitor and had set the size and frequency correctly.
3) Given the results of (2), I then tried logging in as myself in runlevel 2, did startx again, but this time the display failed to come up again.
I installed the nvidia proprietary drivers with click-install and everything perfect, I have desktop effects working but the problem is that when you open the config. screen settings to make sure everything was really good, I get to screen unknown April.
The maximum resolution is the correct 1440 * 900 for 19 "but the refresh rate by not recognizing the monitor down to 50hz me and gives me the option to 60hz as it was before installing the nvidia drivers.
CHECK OUT THIS THREAD INSTEAD: http://ubuntuforums.org/showthread.p...93#post8937093 I got a problem with my xorg.conf file. I'm just not able to add display resolutions. I'm running Ubuntu 9.10 x86 with Xfce4 desktop enivorment. I got an old Nvidia 6600 GT. I'm on a 21" IBM CRT, and i know that it's good for 2048x1536 @ 75hz.
I know that it can handle 30-130 khz Horizontal and 40-170 hz Vertical.
I also know that i would like to be able to use 1600x1200 @ 85hz.
Right now I'm just not able to go past 1024x768 @ 50hz. I've installed the restricted nvidia driver from the popup restricted driver menu, also tried to downgrade to an earlier driver, did'nt work, then i upgraded again to the newest driver that was easily available through Envyng-gtk. Still no more resolution choiches.
sudo dpkg-reconfigure xserver-xorg just don't work. Nothing happens when i write it in the terminal.
I am having video issue with ubuntu 9.10 and centos 5.4 cannot get resolution higher than 800x600 on Viewsonic vg930m monitor...The first time I installed ubuntu 9.10 worked great, since then no better than 800x600 on both linux distros. Any ideas it is very annoying, like using web browser on a small tablet pc....This monitor works great with opensolaris, though.
Using both distros in virtualbox right now but even if not virtualized install on hard drive I cannot get higher than 800x600...Driving me nuts.
I'm a new Fedora/Linux user and I've just setup my first laptop to use Fedora 14. However, I've come across an issue and I've done a lot of searching on various forums etc and basically I'm going around in circles. I've had my PC hang already after I tried to create a xorg.conf file. I have since removed the changes I made.
I have a a SIS 771/671 PCIE VIA Display Adapter (rev 10). I got this info via the lspci command. The problem I have is that it's not letting me select a resolution above 1024 * 768. I know it has higher resolutions as when it was a Windows XP and Vista PC I had higher resolutions. There has to be an easier way to set a screen resolution that manually editing cryptic files and knowing refresh rates etc.
I'm newbie linux user and I want to ask a question about my laptop display is too big i think its because of my screen resolution, how can I change my monitor resolution?
I am now using Ubuntu 9.10. The prob is I am not able to increase the resolution of display. It is showing only 800 x 600 display. While trying to increase the resolution it is showing "Unknown Monitor". So, how can I detect the monitor so I can increase the resolution of my system.
I searched the archives and didn't find anything on this, and was just wondering if there is a problem if you load Ubuntu 9.1 and have a display that's higher than 1024x768. I'd prefer a machine with a higher res, but I've heard that Ubuntu will only go as high as 1024x768.I'm guessing, however, that by 9.1, it should recog the higher res while loading and it won't be a problem, but thought I'd check before shelling out on a machine with a nicer display.
I installed Karmic on an older PC I had laying around, and the only trouble I am having is with screen resolution. It uses an old ATI chipset (onboard) for video, and it doesn't seem to do EDID correctly, so I can't display anything higher than 800x600. I have tried creating an xorg.conf, but it's still not working. How can I tell Xorg to ignore the fact it can't detect a widescreen monitor and display something larger than 800x600? I noticed the log says the sync's are out of range, but I am not sure how to fix it.
I installed Natty about a month ago. First time i installed, i got this same problem.Installation pendrive works on 1920x1080, and the first time it boot it was lovely.I did all the recommended installs, including ATI / AMD proprietary FGLRX Drivers, and the second time my machine boot, it came on 1600x1200. I did some troubleshooting with xrandr, and was able to get HD resolution again, until i rebooted, and then i couldn't even get it with Xrandr.
This is really driving me nuts. I was able to get it fixed by going into recovery mode, and running ubuntu in low graphics mode, i was choosing reconfigure and it worked sometimes, but now i'm stucked with 1600x1200 and i hate it. I don't want to go back to windows, and i really followed every trhead i found with solutions and can't get it to work.I forgot to mention that i have an Ati Radeon 4670 video card. Also i am a total n00b on linux, i am good at following instructions though
I just installed Ubuntu 10.10 on my Dell Latitude D430 that I use at work. I have it on my desk docked going to a Dell LCD Monitor. When I go into the monitor set up it says Unknown for the monitor and Laptop for the actual laptop display. Also, I have very low resolutions for the "Unknown" monitor.
I am trying to resolved this issue so that I have better resolutions on the external monitor and then I can try to extend the desktop between 2 screens.
I found something online about adding the intel PPA and I did that, but now what. There is no xorg.conf that I can find for 10.10.
I gave up on ubuntu few months ago and now I'm giving it one more chance since I am already sick of Vista. Okay, I researched all over google for specific problem and I think there are few possible problems such as not recognizing Monitor (Polaroid 1911-TLXB) or missing driver (Intel 82G33/G31). I have DELL Inspiron 530. Im stuck with 800x600. I did try SYSTEM>ADMINISTRATION>Hardware Drivers and it searched and found NOTHING.
I installed Ubuntu 9.10 on an old PC, Dell dimension L550r, PIII500, 512M ram. There is a problem that monitor is not detected. I could logon as 'xterm' type, but the window size is only 1/4 of screen. When I logon as 'GNOME', it seems screen is not refreshed. media player window is blank, but can see a static image if minimize and restore window. Even terminal window is blank.
Go to "System"->"Preference"->"Display", shows "monitor unknown". I can not find file /etc/X11/xorg.conf, is this normal? xrandr command output: Screen 0: minimum 640x400, current 1024x768, maximum 1024x768 default connected 1024x768+0+0 0mm x0mm 1024x768 60.0* 75.0 70 832x624 75.0 .....
Mine is, ever since I installed the (wrong) opensource video driver for my Ubuntu 9.04 & Lenovo ThinkPad T41 (the one model, imho, they should never have let out the door!), uninstalled it by far-less-than-recommended means (ie, I used Synaptic and sudo apt-get remove and apt-get purge). End up is now my screen has a max resolution of 800 x 600, and Display panel insists that this laptop's screen is an "Unknown" Monitor.
Any tweaks to /etc/X11/xorg.conf (adding vertical refresh and horizontal sync rates for example) has resulted in its own weird behavior. On having my password accepted at login, there's a half-second of white that "rolls" over the screen horizontally. The next thing I see is a diagonal broken streak of white about 2 1/2" down from the top of the screen and 3 inches in from the right-hand side. The next thing I see is a buzzed,jagged rendition of my normal desktop. Nothing at all is clear, and the jags seem to redouble themselves the further one scans down on the screen. The only thing one can do in this situation, and I've done so enough times to know, is a hard reboot (power button for ten seconds or however long it takes).
And as I don't rate sh*t for a shilling on the Ubuntu forums, and as Google has been worse than useless every time I search for problems as detailled as these (it's like K-Mart: it has what you want until you go to look for it!), and as my one self-styled "Lunix-Geek" friend (now in the UK) has only briefly battled the xserver-xorg beasts, I'm coming here to see if anyone knows something else I could do besides bite the bullet, say goodby to my accumulated goodies, and reinstall Ubuntu.
I have a new Television that is connected to a computer running Ubuntu 10.04 with a VGA cable. It works, but the only resolutions I can use are 1024x768, 800x600 and many lower ones. Since the resolutions are 4:3 and the television is not, there are big black areas on the side. I can chose format - wide screen on the television, but then the proportions are wrong. And when I play a movie, it's usually very small with big black areas on the edges.
I got rid of these drivers, I'd used them if they'd work, but they just made matters worse.Any ideas what to do? Maybe upgrading to 10.10 would help? But I'd prefer to stick with the LTS versions if possible.
I installed 10.04 on new computer for office, got everything working great at home with old 15" monitor, took to office hooked up to Multisync 97f monitor, and not recognized 640x480 is best. I Have onboard Geforce 6150se/ 430 and have the newest driver installed from Nvidia 256.44. I tried to install everything that said multisync in synaptics but screen jumps around when trying to click on anything because it don't fit right.
recently found a post that had the same plymouth booting to text only issue i was having so i folowed the instructions and loaded the script.when it got to the resolution part i put in 800x600 24bit as i have a acer netbook and i think the default is to large,when i rebooted my plymouth came up yaaaa prob solved but the plymouth was very wide and poor quality,also before the pymouth the screen turned pixely and when the desktop came on it was very poor qualilty,i went to system preference monitor and it says unknown and none of the opetions there are available to me,i used terminal and tryped x{somthing} for checking minimum and maximum and it said failed to load.what can i try,the resolution now is ugly and wayyyyyyy to big for my little netbook.
I am using Ubuntu Server and would like to recieve an email once a day listing mac address's that have requested an ip address that are not in my list of known mac address's.
lookup=`grep $mac /root/dhcp.macs`
#This does not work as the first entry mac1 will be okay but mac2 and mac3 will not
#It will try to use mac2 as the file to look in which won't exist
#I need to make it loop through for each line of the variable and add that to the lookup value diff $mac $lookup
#I think this should differentiate known from unknown if i can get a lookup value
After upgrading to 11.04, I've been experiencing this weird issue with my monitor. Every time I reboot or turn the monitor on, the colors in Ubuntu are all wrong -- really green. If I go into my monitor's control panel and go to the "Input Color Format" setting and switch it from YPbPr to RGB things go back to normal.The problem is that I can't seem to save this setting. Every time the monitor is turned off it goes back to the wrong setting. I never had this issue before so it makes me think it may have something to do with the upgrade to Natty. The monitor is a Dell SP2208WFP and it's connected to my computer through an HDMI port. I use the Intel video driver.
This issue was resolved in Lucid and Maverick; now it's back... This happens after only 2-3 minutes, even when the screen saver is set to activate after 20 minutes. I believe this has something to do with ACPI power management.
I'm currently running an up-to-date copy of Ubuntu 11.04, but I'm noticing some strange behavior with the monitor settings. First of all, I started investigating this because I'm seeing a lot of screen tearing while watching videos full screen as well as while the screensaver (lattice) is running. On Ubuntu 10.10 I was able to simply set the refresh rate of my monitor to 60Hz through the Nvidia tool and everything worked great. Now, this is no longer the case. I'm using a Samsung Syncmaster 205BW monitor with an Nvidia 8600 GT video card. They are connected with a DVI cable.The strange thing is, the default tool, Monitors, claims my monitor is "unknown" and will only allow me to select 50Hz, 51Hz, and sometimes 52Hz for the refresh rate.
The Nvidia tool claims that my monitor has been detected as a Samsung Syncmaster and is configured to run at 60Hz.However, another area of the Nvidia tool claims that my monitor is using a refresh rate of 59.95Hz. none of these solutions had any effect. I'm still seeing video tearing. I let the Nvidia tool re-write my xorg.conf file after trying these solutions.
