Ubuntu Installation :: Monitor Display Resolution 9.10 X86 Xfce4?
Mar 8, 2010
CHECK OUT THIS THREAD INSTEAD: http://ubuntuforums.org/showthread.p...93#post8937093 I got a problem with my xorg.conf file. I'm just not able to add display resolutions. I'm running Ubuntu 9.10 x86 with Xfce4 desktop enivorment. I got an old Nvidia 6600 GT. I'm on a 21" IBM CRT, and i know that it's good for 2048x1536 @ 75hz.
I know that it can handle 30-130 khz Horizontal and 40-170 hz Vertical.
I also know that i would like to be able to use 1600x1200 @ 85hz.
Right now I'm just not able to go past 1024x768 @ 50hz. I've installed the restricted nvidia driver from the popup restricted driver menu, also tried to downgrade to an earlier driver, did'nt work, then i upgraded again to the newest driver that was easily available through Envyng-gtk. Still no more resolution choiches.
sudo dpkg-reconfigure xserver-xorg just don't work. Nothing happens when i write it in the terminal.
I have never used Linux always windows so heres the problem the display only has 2 settings 640x480 and a smaller one and it say unknown monitor. I installed the drivers in hardware driver in systems I'm running Ubuntu v 9.10 if that matters and the video card is a Nvida mx440.
I am having video issue with ubuntu 9.10 and centos 5.4 cannot get resolution higher than 800x600 on Viewsonic vg930m monitor...The first time I installed ubuntu 9.10 worked great, since then no better than 800x600 on both linux distros. Any ideas it is very annoying, like using web browser on a small tablet pc....This monitor works great with opensolaris, though.
Using both distros in virtualbox right now but even if not virtualized install on hard drive I cannot get higher than 800x600...Driving me nuts.
I'm a new Fedora/Linux user and I've just setup my first laptop to use Fedora 14. However, I've come across an issue and I've done a lot of searching on various forums etc and basically I'm going around in circles. I've had my PC hang already after I tried to create a xorg.conf file. I have since removed the changes I made.
I have a a SIS 771/671 PCIE VIA Display Adapter (rev 10). I got this info via the lspci command. The problem I have is that it's not letting me select a resolution above 1024 * 768. I know it has higher resolutions as when it was a Windows XP and Vista PC I had higher resolutions. There has to be an easier way to set a screen resolution that manually editing cryptic files and knowing refresh rates etc.
I'm newbie linux user and I want to ask a question about my laptop display is too big i think its because of my screen resolution, how can I change my monitor resolution?
I have done a scratch install of Ubuntu 11.04 (Natty) successfully today. I am facing problem while adjusting my monitor resolution.
My motherboard is pretty old, Kobian 845GLNDSMx. When I tried to adjust the resolution from Preferences -> Monitors, the resolution is shown as 800x600 (4:3), Refresh Rate - 0Hz and Rotaion as normal. "Monitor Unknown" is highlighted on the window. Moreover, "Detect Monitors" doesn't work.
I am new to Ubuntu. I installed Ubuntu 8.04 and it detected my Acer monitor AL1716 correctly and it works fine. However when I installed Ubuntu 11.04 it shows the monitor as " Unknown Monitor" and the maximum resolution is 1024x768 and I cannot set the native resolution which is much higher. My motherboard has Intel 845G chipset and built in graphics. I tried Ubuntu Software Center, but couldnot solve the problem.
I purchased a lenovo G550 recently and immediately dumped the Windows OS for Ubuntu 9.10. The display is currently defaulting to 1366x768. From reading it looks as though this display can support both 16:9 and 16:10 aspects. I have ran through the xrandr commands attempting to set my resolution to something...anything bigger than 1366x7768 (I'm used to 1600x1200 from my old T61, so this is painfully small). As a test I am trying to get 1920 1200, from my xrandr results it looks like it should be within the lcd's range. xrandr commands failed on me as I have seen on a couple other intel based resolution problems. I don't fully understand the root of the problem and have not had any luck in my searches. So I have also attempted to manually create the xorg.conf file, not luck yet.
When I try to change the resolution, it only shows 800X600 and 640X480 or something similar, nothing regarding a custom resolution. When I use the "Install Guest Additions" it won't mount because of some error, and so I can't open it, and even if I could mount and open it *I've tried it in other distros that don't automatically install it for you* I have no idea what to use. I've tried all of the .sh, even the autorun.sh and giving it executable permissions, and it STILL doesn't work. Perhaps I'm missing something, or there's a documentation out there that I can't find, but I can never get them to work. How can I fix this problem? I know in sbopkg, there's 32-bit Virtualbox Guest Additions but that doesn't work. The reason why I installed the 64-bit one is because I don't have 6 CDs to spare and I'm almost out of bandwidth and it has to last me a week. *I think around 200GBs out of 250GBs taken up so far, or more*
I have been encounter 2 bugs on 2 sides of the coin. Seems it doesn't fix since Wheezy till now.
1. When I don't install any nonfree firmware I'm stuck at 1024x768 resoultions unable to turn to 1366x768 2. But when I install nonfree firmware my 1366x768 was solved but I encounter other new bugs
>> On Jessie: XFCE4.10 doesn't save any wallpaper everytime when reboot the pc & always reset to default. But when remove nonfree firmware the bg save normally but I've to stuck at 1024x768 resulotion. This also happen on Wheezy as well. >> On Stretch: XFCE4.12 workspace become too long ugly. But when remove nonfree firmware the workspace become normal but I've to stuck at 1024x768 resulotion once again.
So any way with nonfree installed without this XFCE bugs or without nonfree driver install but make resolution 1366x768 work for not to stuck in 1024x768 resolutions. Overall I'm quite satisfy Stretch testing than Jessie Stable.
why both ubuntu and centos 5.4 will only give me 800x600 resolution on my monitor when opensolaris immediately gives me 1280x1024?The first time I tried ubuntu it gave me 1280x1024 and now will only make 800x600...This is a viewsonic VG930M Monitor..
I have a problem with my graphics (exactly this one: [URL] I've got an Intel 845G chipset and a LG Flatron F900P monitor.A friend of mine convinced me to try ubuntu and I installed the 10.10 version. Everything (except the monitor's resolution) works all right.
My computer is: IBM Net Vista 8305-21G Chipset: FRU PN 49P1599 (Intel 845G)
I installed 9.10 on a computer I'm working on, and right away the graphics went out. It won't display the proper resolution without shoving the display significantly to the left.
After MUCH Googling, I found that this can be fixed by a driver called i915. After much MORE Googling, I found [URL], which as you can imagine filled me with relief.
And THEN I try to follow the instructions and discover to my pure horror that GRUB has been gutted and made unusable in 9.10. GRUB2 just simply does not seem to have an option to insert the i915 driver into my boot command.
should I just forget this unstable release and burn a 9.04 disk instead?
Slackware 13.1, on a Dell... Opliplex GX260... running XFCE4, as root. Stuff runs fine. However, the monitor goes to powersave mode after 10 minutes of inactivity. I've turned off power management in the kernel, in the app., have checked the xorg.conf, checked everywhere I can think of, can't find where this is being set. how I can turn this off?
after upgrading from 10.10 to 11.04 i received the Unity as a default. with the help of this forum i figured out how to get the Gnome.i would like to try the Unity but when i am switching to Unity i cant get the resolution i need to my external monitor.i have an application, Switch resolution that doesn't work under the Unity but does work under Gnome.i can change the resolution in the external monitor to its native resolution but than i get the upper panel in a good resolution and below only black without any window or anything.
Install went through smoothly in both my laptop and an old Dell Optiplex GX 270.
Screen looks fine on laptop but terrible on the Dell. It's stuck on Refresh rate of 60Hz and flickers pretty bad. 60Hz is the only rate offered! How can I change the refresh rate to ~65-72Hz like is possible on earlier Ubuntu versions to ease eye strain?
How can I know the display resolution (e.g. 1280x1024 px) without starting X?I mean: let us suppose that /etc/X11 was renamed to /etc/x11. After reboot Debian starts in text mode only.
Ive just installed Fedora 12, max resolution option is 800*600 can someone advise how i can adjust or improve the resolution to at least 1200*700?Hardware: HP D330m, 2.8GHZ, 700MB RAM, VGA is a Intel Extreme Graphics Display.
I have installed Ubuntu 10.4 on Virtual Box, I have installed it successfully, the only problem is when I check the display settings it only have 2 options : 600 X 400 and 800 X 600 and this makes it difficult to work on Ubuntu as 800 X 600 is half the size of my desktop. How I can increase / configure the display settings so that atleast I can fit ubuntu screen into my screen size.
I did install the addition application, restarted the OS but still I don't see any display resolution 1200 X 800, tried pressing ctrl+D nothing happens, after installing I saw it updated mouse cursor now i don't have to press ctrl key again n again to enter into the ubuntu OS but still struggling with the resolution as it's too small, please guide me (here is the screen shot of my screen after installing the addition app).
I am trying to install Fedora 11, but the monitor that I am using is only 640x480. When the window comes up to start the install, I cannot see any of the buttons or tabs for selecting the items. How can I adjust the resolution so that I can see the entire image in my screen?
I searched the archives and didn't find anything on this, and was just wondering if there is a problem if you load Ubuntu 9.1 and have a display that's higher than 1024x768. I'd prefer a machine with a higher res, but I've heard that Ubuntu will only go as high as 1024x768.I'm guessing, however, that by 9.1, it should recog the higher res while loading and it won't be a problem, but thought I'd check before shelling out on a machine with a nicer display.
I know there are many threads on similar issues but I can't find anything that will work. Not sure if I need drivers or what to do - I feel really stupid as I should be able to get this right but I am at a brick wall. Basically I have a 20inch monitor hooked up to the on-board graphics card and cannot get higher resolution than 900 x 600. It should be at 1280 by 1240. This is a brand new install with the latest Ubuntu 10. Under monitor preferences its says 'unknown' for monitor type and I don't have any driver disk for this screen but never needed one previously.
I have just installed Fedora 10 and all went well except that the resolution is set to 1024x768, which is not cool on a 22" HP w2207h LCD monitor. When I bring up Monitor Resolution Setting the Mirror Screens is checked and 1024x768 is the highest resolution. If I uncheck Mirror Screens and select "Laptop" I am able to select 1680x1050, but it now has my desktop in the upper left hand corner of my monitor. Should I be looking for a driver for my i845G graphics processor?
PS: I am new to using Linux please be patient with my ignorance.
After spending the last couple of days running different distros on a old Compaq armada 7800 I've settled on Debian, as it's recognised most of the hardware with out to much tinkering
Only problem i have is the display resolution i need to run at 1024 x 768 but the max i can get is 800x600 I believe the display adapter is a S3 Virge/MX 2D/3D Dual Display Accelerator
Is there a driver/package I can download to correct this issue
I can use the console as long as some one give me Janet and John instructions
I setup 10.04 on an older Athlon XP 3000+ ASUS A7N8X board with a Radeon RV250 video card. It works fine and dual boots with XP on the LCD monitor I have. I took it to my mom's an connected to a iiyama Vision Master 450 CRT. When I boot, I get the grub menu, and if I pick Windows XP, it boots fine. If I pick Ubuntu, the screen goes blank, as small underline cursor appears at the top left, and then the monitor goes into sleep mode and the keyboard is no longer responsive.
I cannot seem to gain access. I cannot hit CTl-ALT-F2 (or ALT-F2) to get to text login (screen is sleeping and no keyboard control). I tried Live CD, it shows a graphic at the bottom of the screen and then goes blank as well! Seem like something with monitor resolution, but I cannot seem to figure out how to force it to work. I can't seem to figure out how to get into command line mode on boot either.
I did a LiveCD to USB install, following the directions I found at [url] When I went to reboot to the USB stick, all I get is a black Screen (monitor is on and lit, just nothing on the display) No cursor or command prompt. I've tried holding shift to bring up the GRUB menu, changing splash quiet to nomodeset, or just adding nomodeset after the splash quiet thing. I've even tried xforcevesa instead of nomodeset still black screen. Looking at the logs nothing is current as of the last time I tried to boot the computer, it's strictly what was written when I installed it to the stick. Other things I've checked/tried, Pressing CTRL+Alt+F1 at GRUB to get TTY, all I get is that blank screen. I've Checked etc/default/grub to ensure the timeout was higher then 0. The Install CD seems to be OK but I have (as it did another install successfully) but I haven't done any throughal checking of it (there was no check this disk on the first screen of the LiveCD) The USB sticks also seem to be ok (in windows though). Using the disk utility on the live CD I did check the file system on the USB stick, the "/" partition came up clean. Anybody have any other thoughts on this install, any thing else I can check?
I installed Karmic on an older PC I had laying around, and the only trouble I am having is with screen resolution. It uses an old ATI chipset (onboard) for video, and it doesn't seem to do EDID correctly, so I can't display anything higher than 800x600. I have tried creating an xorg.conf, but it's still not working. How can I tell Xorg to ignore the fact it can't detect a widescreen monitor and display something larger than 800x600? I noticed the log says the sync's are out of range, but I am not sure how to fix it.
I am facing problem with the fresh installation of Fedora 11. (I have moved from Fedora 9). When I try to view videos on ..... or use the Cheese Webcam Booth, I get blurred lines on the screen and I am unable to see any video or pic.
Also I noticed that the when i go to System > Preferences>Display, it shows me UNKOWN MONIOR.
However, if I got to System>Administration>Display and enter the su password, it shows me correct monitor and the graphics driver.
I am not sure if my original is related to the Unknown Monitor.
I also tried to install Nvidia driver but it crashed the xserver and I had remove the driver.
My Monitor is LG 700E and Graphics card is from intel. as I am not able watch any video.
