tried to install linuxant drivers which failed and then I uninstalled it. Now sound does not work, installed alsa backports again, installed alsa, alsautils again as well. no luck.
aplay -l
aplay: device_list:235: no soundcards found...
This is on maverick.
My sound stopped working.
Code:
$ aplay -l
aplay: device_list:240: no soundcards found...
But:
Code:
$ sudo aplay -l
**** List of PLAYBACK Hardware Devices ****
Home directory /home/georgii not ours.
card 0: Intel [HDA Intel], device 0: ALC662 rev1 Analog [ALC662 rev1 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
Same with alsamixer:
Code:
$ alsamixer
cannot open mixer: No such file or directory
But:
$ sudo !!
shows me the mixer.
Anyway, the sound is just gone. When I do: .....
It says: "PulseAudio seems to have crashed. Do you wish to report a bug?", then crashes.
I recently had a brain cramp and told Phonon to forget my sound card(s). I have an on-board card and I have installed an old-school Sound Blaster CT-4832. I have followed the steps listed in the comprehensive sound trouble shooting, and still no luck!
Code:
gentle@Desktop:~$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: NVidia [HDA NVidia], device 0: ALC888 Analog [ALC888 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
[Code]...
I have seen several posts on various message boards that touch on the no sound over hdmi on nvidia cards issue (mine is an 8400 gs) and the general consensus seems to be create a custom edid and tell x to use it. So here is the heart of the post: I downloaded http://analogbit.com/sites/default/file /edid_disable_exts_v1.2.tgz to modify my edid but I don't know what to do with it. I extracted it and tried $ make and $ sudo make install But that wasn't the ticket,
View 1 Replies View Related1. I run Suse 11.2 with two sound cards , one HDA comes with motherboard and second is USB, which I use for skype and talking. In YAST everything is fine the motherboard card is marked as prime card and the usb card is marked as second. But often when I log in alsa decides that second card is main and I have to pull out the USB card, run command "rcalsasound restart" and put the USB back afterward. It is a way that to be fixed in the way that alsa remember my choices forever. 2. The other problem is that from time to time the sound suddenly dies and I have to bring it up with rcalsasound restart again.
But I have to admit that their significant improvement with managing sound with PulseAudio.
I have an nvidia card and a motherboard with an internal sound card.
The nvidia card hogs alsa, and it's really obnoxious because I don't use hdmi for audio (or video, for that matter, crt all day)
I would normally just blacklist the module that the card is using, but I hit a hiccup...
This is the readout for the gfx card from lspci -v
Code: Select all01:00.1 Audio device: NVIDIA Corporation Device 0fbc (rev a1)
Subsystem: ASUSTeK Computer Inc. Device 84bb
Flags: bus master, fast devsel, latency 0, IRQ 25
Memory at fe080000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Endpoint, MSI 00
Kernel driver in use: snd_hda_intel
And this is the readout from the motherboards internal audio card
Code: Select all00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) (rev 40)
Subsystem: Gigabyte Technology Co., Ltd Device a132
Flags: bus master, slow devsel, latency 32, IRQ 16
Memory at fe500000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Kernel driver in use: snd_hda_intel
Since they have the same kernel module, all the internet advice is pretty much moot, because I can't figure out how to effectively shut off one without killing the other as well. Huge PITA.
Have a couple of very annoying problems. I recently did a re-install of Kubuntu Maverick on my HTPC/fileserver box.It has an onboard (Realtek?) audio card, recognized as... I think, ALC888... Yeah, not sure, KInfoCenter lists a bunch:ALSA Sequencer DeviceUSB 2881 Device ALSA Control Device (my DVB-T stick)ALSA Timer Device
HDA Intel ALSA hardware specific Device
ALC888 Analog ALSA Capture Device
ALC888 Analog ALSA Capture Device
[code]....
Up until about a week ago using Kubuntu 9.10, the sound on this computer was fine, but now every day when I turn the computer on I have no sound and I get a notification from Phonon saying:
The audio playback device NVidia (ALC883) does not work.
Falling back to.
If I turn the computer off and then back on, sound is working again. code...
I have installed a wrong driver few days ago from
http://ubuntuforums.org/showthread.php?t=540296 code...
I'm new to ubuntu, just knowing little about it.
You can ask for more information for my computer
How can I recover the sound ?
I have tried many, many things to try to get the sound card recognized since upgrading from Mint 8 to Mint 9, and have still been unsuccessful...all modules and up to date and alsa was rebuilt this morning (to insure I didn't mess something up with my prior attempts to resolve). I have only been using Linux for about a month now, and really don't want to have to go back to Windows
Here is a link to my latest hardware and troubleshooting info:
http://forums.linuxmint.com/viewtopi...302076#p302076
Can someone on this forum please assist?
I have a PXE server.I boot one PC (optiplex 740) with hda-nvidia Sigmatel STAC9200, i have sound.I boot a second one (optiplex 380) with hda-intel Realtek ALC259, can see mixers with alsamixer, the xmms graphs moves when playing music, but i don't hear any sound.
View 1 Replies View RelatedI encounter many problems, the most pressing now is the lack of my Ubunto-PC to make use of my M-Audio Delta 1010 LT Soundcard. I installed ALSA package yesterday, but there's still no sign of my Soundcard to be found. sudo aplay -l delivers: aplay: device_list:223: keine Soundkarten gefunden ... (no soundcards found)
[Code].....
I've written a "C" program which transmits audio to a number of computers over a TCP LAN connection. I'm using ALSA, the preemptive kernel, and pthread. After running for 30 minutes or so the slight variation in sampling rates (~+-.01%) among the computers accumulates and manifests as a noticeable differential delay in the sound from the speakers. I know how to detect the variation and would like to dynamically compensate for it by individually varying the sampling rate (ever so slightly) of each playback device to oppose the variation.
Does anybody out there in Linux Land know how to dynamically vary the playback sample rate? I've tried using snd_pcm_hw_params_set_rate() and snd_pcm_hw_params_set_rate() followed by snd_pcm_hw_params() to no avail. They don't seem to work when playback is running.
I just two days ago updated lenny, then unplugged my monitor which raised my video card out of my open system board. This made my debian com freeze and i had to restart. The sound icon looks like its muted or has an X next to it. It says 'No volume control GStreamer plugins and/or devices found.' I tried looking through forums but havent found any solutions yet. I think alsa is installed. I ran alsaconf. It said no sound cards were loaded when unloading them. Then the following cards are found on your system:
hda-intel ATI Technologies Inc SBx00 Azalia (Intel HDA)
hda-intel ATI Technologies Inc Radeon HD 3870 Audio device
legacy Probe legacy ISA (non-PnP) chips
I tried the first two, it says OK, sound driver is configured ALSA CONFIGURATOR will prepare the card for playing now. I'll run alsasound init script, then use amixer.
I then installed libesd-alsa0, replacing libesd0 or something. If I do # alsamixer, then it says alsamixer: function snd_ctl_open failed for default: No such file or directory
Then i tried this
# cat /proc/asound/cards
cat: /proc/asound/cards: No such file or directory
then # cat /proc/asound/modules
cat: /proc/asound/modules: No such file or directory
[Code]....
Did I break the onboard sound card when pulling out the video cord? I was pretty gentle, I just made it slide out i think. I've also restarted a bunch of times. It seems like alsaconf showed some sound cards. Maybe some driver is not installed, but I think I did install a newer gstreamer or part of it.
I'd like to make a complete switch to Debian. One of the things holding me back is not knowing the state of play regarding sound card support. I've been fiddling around on and off for three years trying to get my M-Audio FireWire Solo to work in Ubuntu without much joy. I think there might be greater support for USB sound cards but I'm not certain of this. Onboard cards aren't OK because in my experience these pick up too much noise. After years of using balanced audio lines it's pretty much impossible to go back. That said, a PCIe card isn't completely out of the picture if I can get balanced outs with it.
I'm planning on plugging KRK powered monitors via XLR or TRS cables into the sound card. But my preference at this point is firmly with USB sound cards. Is there an up-to-date list I can check of supported sound cards in Debian? Can anyone here provide a testimonial of their experience? It's important to note that I'm after playback only. I don't want to record ever. That should hopefully make things easier. I'd be looking at using Debian wheezy.
I have just upgraded to Fedora 14, with some hope that a F13 kernel crash issue would be resolved. Alas, not, and I have lost audio in one of my sound cards. I am using 2 sound cards in my computer. The first one (VT 1708 on the M2V MX SE motherboard) is used for FLDIGI (ham radio program). The other one (Creative Labs SB Live!) is tied to a speaker/microphone. At some point in mid 2010, I started getting kernel crash reports (not sure which kernel version this started), and the VIA VT 1708 audio controller stopped working. The SB Live! card works fine.
From mesg, I get:
[9.181148] WARNING: at drivers/pci/pci.c:105 pci_ioremap_bar+0x2c/0x5b()
[9.181186] [<c05c36ad>] ? pci_ioremap_bar+0x2c/0x5b
[9.181194] [<c05c36ad>] pci_ioremap_bar+0x2c/0x5b
[9.181299] ALSA sound/pci/hda/hda_intel.c:2510: ioremap error
I've just pulled out the SB LIVE! card to see if it is causing the VT 1708 controller to fail...there appears to be no interaction.
From lspci -v, I get:
20:01.0 Audio device: VIA Technologies, Inc. VT1708/A [Azalia HDAC] (VIA High Definition Audio Controller) (rev 10)
Subsystem: ASUSTeK Computer Inc. Device 8290
Flags: fast devsel, IRQ 17
Memory at <ignored> (64-bit, non-prefetchable)
Capabilities: <access denied>
Kernel modules: snd-hda-intel
So it seems to know it's there. How to get my sound back (and get rid of this kernel crash every time I start my computer)?
I have an internal PCI sound card, and I would like to find out what MIDI capabilities it has, if any. It is currently using the ens1370 ALSA driver. It has the standard Line in, Line out, and Mic jacks, as well as what appears to be a game port. I think it has some MIDI capabilities, because "cat /dev/snd/midiC0D0" does not fail with "no such device or address," but I don't know if it has MIDI input capabilities, or if it can synthesize, or what. Is there any way to tell?
View 4 Replies View RelatedI've got a problem on Slackware64 13.37, my sound is way to loud even on minimum settings, it just jumps from off to quite loud, this is not a hardware problem as when I use sound from my debian rescue partition I have full control, I have tried using alsamixer as well as the graphical volume control (I'm using xfce but a quick test on kde gives the same results), alsaconf doesn't seem to detect any sound cards, alsa mixer correctly identifies my sound card ( NVIDA ), been googling and searching these forums but all the sound problems seem to be about sound being to low or nonexistent.
View 14 Replies View RelatedI have an M-Audio Delta 44 sound card, and a USB MIDIinterface device, both are recognized, and work. My problem is as each are seen by alsa as sound cards, sometimes the alsa card numbers switch between boots. Is there a way to set these devices to always have the same card number for alsa
View 1 Replies View RelatedI`ve problem with my microphone on fedora 14 with Gnome 2. When i try to use alsamixer command there everything is ok. I tried pulseaudio and HDA nvidia sound cards, but microphone don`t work. How to fix this problem?
View 11 Replies View Relatedhow can I play audio (Mythtv - Play Music) simultaneously on two sound cards using ALSA drivers. I have two cards working well. One card is an onboard Intel cards, and the other card is a USB Audio card. Both cards are working well. I use the onboard Intel to output SPDIF to an amplified. The second USB card is bound to MPD service and it outputs an analog signal to a second amplified. I'd like to have the following configuration: Play to the default card with 5.1 passthrough, while the second card, connected to a second amplifier, plays an analog signal to the same audio played by Mythtv Play Music. In other words, I need to mix somehow and play the same audio on both cards.
Here is the list of cards:
root@mythtv:~# aplay -L
null
Discard all samples (playback) or generate zero samples (capture)
[code]...
I am having issues with my sound..Sometimes when I boot up I get the following when I cat /proc/asound/cards
[digitolx@ssureshot-pc ~]$ cat /proc/asound/cards
0 [NVidia ]: HDA-Intel - HDA NVidia
HDA NVidia at 0xd6000000 irq 225[code]....
This is wrong, now My audigy should be default with the UART (onboard) being secondary. I will be setting this up for my microphone / headset.Now if I restart I will get the following..
[digitolx@ssureshot-pc ~]$ cat /proc/asound/cards
0 [CA0106 ]: CA0106 - CA0106
Audigy SE [SB0570] at 0xb000 irq 66
1 [UART ]: MPU-401 UART - MPU-401 UART
MPU-401 UART at 0x330, irq 10
I'm not sure about what is even loading With the NVidia for sound..Is there a way to default this to the second example?
my computer after being updated a few months back lost its ability to make noise. the sound and volume settings see no input (i have an internal mic) or out put (speakers) hardware. they see no sound hardware at all. im running this on a sager so im assuming its an intel HDA audio thing. is there a package where i could report this bug?
running ubuntu 9.10 64 bit
I've tried googling, but can't manage to figure out how to change the priority order of the sound cards in yast. From yast > hardware > sound, I can see the (default) internal audio from the motherboard, and I can see the usb headset that I would like to be using as the default. How should I go about changing the priority order on these devices?
View 3 Replies View RelatedI have dell inspiron-1545 laptop.I installed rhel5(downloaded from torrent for free),kernel (2.6.18-8el5xen).i got a driver cd from dell containing rhel drivers for audio,video,network.i tried to install those drivers but could not.it asked for dkms 2.0 which i installed.but even now also some errors are coming(like dependencies missing etc.).so no internet ,no sound,no video on my laptop.
Some command outputs:
When i boot every process come OK except(cpu micromodule failed.fatal error and hub port status failed). i think these cards have not been detected.
I have a dns server started with 2 NIC Cards in it. The bios sees both cards but they both dont show in ifconfig. is there a way to activate the second card?
View 1 Replies View RelatedI have been trying to get this web cam working for a long time. lsusb:
Code:
Bus 004 Device 003: ID 06a2:0003 Topro Technology, Inc.
dmesg
Code:
[ 1990.570050] usb 4-1: new full speed USB device using uhci_hcd and address 3
[ 1990.751460] usb 4-1: configuration #1 chosen from 1 choice
Kernel patch: [URL]
Driver project: [URL]
Cheese simply says no camera found. Skryba says no devices found. Since this kernel patch was 2009-04-07 which is nearly a year ago it should be in latest kernel?
[Code]...
I'm trying to set up a 4 monitor sys with 2 different cards. 1 is an ATI, the other an inVidia.
View 1 Replies View RelatedI hear no login sound when I login to my ubuntu. I checked at startup applications and found GNOME login sound is enabled. The command used there is
Code:
/usr/bin/canberra-gtk-play --id="desktop-login" --description="GNOME Login"
.
Its not only this, but there is no other sounds enabled - for mouse clicks etc
I am running Ubuntu 9.10. My work requires me to frequently swap video cards between an ATI Radeon 5870 card and an NVIDIA GeForce 8800 GTX card. My question is: can the ATI driver (fglrx - catalyst 10.2) and the NVIDIA driver (nvidia 190.29) co-exist? Or do I need to reinstall the driver every time I change the card? I would like for the drivers to be able to co-exist so it would only be a matter of restarting my machine with the new card and choose the right xorg.conf file (perhaps from the GRUB menu).
View 9 Replies View Related