Ubuntu Multimedia :: Display A Full Screen With An Nvidia Integrated Graphics Controller
Nov 5, 2010
I have recently upgraded to Ubuntu 10.10. However the bottom of the screen is cut off with only a trace of it visible. I had similar problems with version 10.04 where both and top and bottom of the screen were not displayed.
I have noticed that version 10.10 does not use the proprietry driver the previous versions used.
In desparation I have tried Kubuntu but the results are still much the same.
Does anyone have any idea how I can display a full screen with an Nvidia integrated graphics controller.
View 9 Replies
ADVERTISEMENT
Jul 9, 2011
I really wanna use the OS. I wiped my laptop and installed it but I can't change my screen resolution (it's stuck at 1024 X 768 and my refresh rate is at 0 HZ) I tried installing a driver that was for both the i9xx and i8xx chipset family but it doesn't look like it helped anything. I want to be able to play World of Warcraft Wrath of The Lich King but when I try it the way the computer is now the the frame rate is really really slow. I also need to fix my audio because there's crackling that comes from the speakers often. I attached a screen shot of what I get when I enter the command: sudo lshw -c video Changing the resolution isn't the problem so much as the fact that I can't change the refresh rate from "0 HZ" to anything higher so that my game will play smoothly. I would also like to put compiz fushion on my laptop as well but I don't believe it will work unless I resolve this problem.
View 9 Replies
View Related
Jul 18, 2011
[code]...
Just got World of Warcraft Installed and when I start the game after I get past the 2 cinema's while I'm trying to click yes on the rules the screen seems to bee flashing over and over and over. I was thinking maybe the 3d accelerator isn't installed or maybe I need to install something because its Intel?
[code]...
View 2 Replies
View Related
May 25, 2010
I have a PCI graphics card, Nvidia Geforce FX 5500, but can't get it to work. I have 10.04 installed on a Dell Dimension 3000, P4, 1Gb RAM, integrated graphics. I installed 10.04 without the card in the machine, then shut down and plugged the card in and booted it up again (BIOS setting is 'onboard' for integrated graphics, 8Mb; only other option is 'auto'). Checking the hardware drivers I can see the recommended Nvidia drivers (v173, not yet activated) and lspci gives me the integrated as well as the Nvidia listing:
01:02.0 VGA compatible controller: Nvidia Corporation NV34 [GeForce FX 5500] (rev a1)
00:02.0 VGA compatible controller: Intel Corporation 8286G Integrated Graphics Controller (rev 02)
So far so good, but that's where it ends. Changing the BIOS setting to 'auto' turns the screen off on reboot, both for the monitor connected to the VGA port of the Nvidia card and for the monitor connected to the VGA port of the motherboard. I have to shutdown, take the card out and set the BIOS back to 'onboard' to be able to boot again (and shutdown, plug the card back in and boot up again to get back to where I was).
Activating the recommended hardware driver and rebooting (still with BIOS set to onboard) gives a blank screen (screen is still on and there may have been a flash of the purple screen with the ubuntu logo); nothing else happens no matter how long I wait. Rebooting doesn't help, it turns off the screen; same result for booting in recovery mode. I can get to the GRUB bootloader and when I replace 'quiet splash' with 'nomodeset' I manage to boot again with the monitor connected to the VGA port of the motherboard, but am not anywhere closer to getting my monitor working on the Nvidea card.
View 5 Replies
View Related
Sep 15, 2010
I am testing Suse 11.3 and have run into a problem with Intel's integrated graphics and resolution. Here is a dump of the hardware information I pulled from yast.
[Code]....
View 1 Replies
View Related
Jan 3, 2011
when i start uubuntu it automatically goes to tty with out letting me login. then when i press startx it says:
NVIDIA: failed to initialize the nvidia graphics device pci:0:13:0
nvidia: please check your systems kernal log for additional erroe
nvidia: messages and refer to chapter 8
nvidia: failed to initialize the nvidia graphics device!
nvidia: screen found, but none have a usable configuration
fatal screen error: no screen found
right before this i had activated a nvidia graphics device
View 9 Replies
View Related
May 22, 2010
I have a desktop computer with integrated ATI graphics. Specs below and lspci log attached. I was running 9.04 Jaunty Jackalope until 1 week ago. Everything worked fine from the day I installed it. It's default driver worked fine and graphics requiring applications like Google Earth and Secret Maryo Chronicles (game) ran smoothly. Then about a week or so ago I did a clean install of Lucid on this PC. And now Secret Maryo Chronicles runs choppy and Google Earth doesn't run and display images smoothly. I could understand having problems like this if I were switching to Fedora or something but I'm still using the same distro (and both are recent versions).
Computer Specs:
ATI Radeon Xpress 200 integrated graphics with 256 MB RAM
Intel Pentium 4 clocked at 3.00 Ghz
2 GB RAM (.25 being used for graphics card)
500 GB Hard drive (355 for Ubuntu)
2 DVD drives
View 2 Replies
View Related
Jan 10, 2010
I have downloaded the recommended NVIDIA driver for my Quadro FX 1400 graphics card which has 256 MB RAM. I have my laptop in a docking station and from the docking station is a DVI to HDMI converter then HDMI cable to my TV (the idea is to use it as an internet TV slave! ). When I come to configuring the NVIDIA X Server, it correctly detects both my laptop screen and my TV via the HDMI connection. However, when I come to save the settings for the X server and go to restart it, it cannot save the configuration file. This is most annoying as it does not allow me to use the dualview I need.
The second problem comes when I use something like the BBC iplayer or anything that uses the flash player. I have the latest flash player with Firefox which works fine in non-full screen mode. However, when switching to full screen, the CPU load jumps to 100% and the playback is really jerky. Had this running the beloved windows XP before and could handle full screen no problems. I have seen a few posts here which show workarounds to zoom in on the small screen on Firefox but would prefer to run it in the full screen mode.
View 2 Replies
View Related
Jan 25, 2011
This obnoxious bar has just appeared in Smplayer at the top of the screen. It stays there even when I go full screen. Now full screen isn't full screen and there are black edges on both sides of the screen. I have not be able to figure out how to hide it. I do not need or want this onscreen display. How can I configure Smplayer to make this go away? How can I get my 16:9 full screen aspect ratio back? I have done nothing to mplayer or smplayer as far as editing any or changing any configuration files. I tried several videos and it displays on all of them. It was not there last time I used Smplayer.
View 9 Replies
View Related
Aug 17, 2011
having trouble setting up a dual monitor from my Dell xps laptop using an HDMI port. It dual boots onto Ubuntu 10.04. The computer has a Nvidia GeForce GT 555M with Optimus graphics card I need to make sure I have not installed the restricted drivers. So I think what is happening right now is that the graphics are shown off the integrated graphics card. This is my output from <lspci | grep VGA>
Code:
00:02.0 VGA compatible controller: Intel Corporation Device 0126 (rev 09)
01:00.0 VGA compatible controller: nVidia Corporation Device 0dcd (rev a1)
The forum recommends to use this program called Bumblebee but I have had some issues with that in the past. Is there somehow I can setup my dual display while staying on Ubuntu 10.04 and not installing Bumblebee? I have researched into setting up dual display walkthroughs before but they all concentrate on nvidia or ATI configurations.
View 6 Replies
View Related
Aug 19, 2010
I have been unable to get both opensuse 11.2 and 11.3 32 bit versions work properly on my DELL Latitude E6410 laptop. With both 11.2 and 11.3 KDE Live CDs I get no graphical display when I attempt to boot into the Live system. VESA mode does not help either, only text mode works. So I installed the system in text mode but during the first boot the screen went blank again.
One peculiar thing is that 11.1 installs and boots fine, what gives? Is this even supported or I shouldn't even try to bother getting this setup to work? Has anyone been able to run opensuse 11.3 on a Core i7 integrated Intel graphics system with X system working?
View 9 Replies
View Related
Jan 14, 2010
I have installed the latest debian on a dell optiplex gx260 which has a 82845G chipset and there are some strange problems.The system is configured with autologon as a standard user. Sometimes, after logging on, the screen goes black but if I connect to it with vnc, I get a working desktop. Yesterday I booted it without a display attached to it and now I cannot set it to the right screen resolution anymore (1440 x 900) which was working fine before.
I have googled and searh the forum but cannot find the right information. According to Intel, the latest driver should be in the distro but I cannot find any details about that (version/date). grep Driver /etc/X11/xorg.conf returns
[Code]....
View 15 Replies
View Related
Dec 25, 2010
I previously had a dual output Nvidia 7300le which worked fine with 2 monitors (2xDell e196fp). Now however I have just added a new monitor to my setup (and a different graphics card). I've gotten to the stage where it recognises all 3 monitors (2xdell 196fp and 1x samsung syncmaster) and also the new graphics card (Nvidia PCIe 210)...it took me ages to get to this stage and a lot of hacking around in the bios!
I've got it so that it runs two monitors fine (the two connected to the graphics card) but I cant manage to extend the desktop onto the monitor connected to the integrated GPU (I can on windows). It definitely recognises it as when I startup it gives me a command prompt on the 3rd window (integrated gpu) and then when I do startx it runs the session on the other two monitors!
[Code]...
View 1 Replies
View Related
May 2, 2010
I have a Gigabyte GA-MA74GM-S2 motherboard with integrated graphics that shows up on lspci as an ATI Radeon 2100. I also bought a PCI-Express Nvidia graphics card so I could use the VDPAU feature on Linux (plays H.264 in hardware). The BIOS has three settings about which display to initialize first:
Integrated graphics
PCI graphics
PCI-Express graphics (PEG)
I set the BIOS on PEG, but
I cannot get anything, not even a splash screen or POST messages, to emerge from the PCI-Express graphics card. (I'm using a DVI connector; the card also has an HDMI output.)I cannot get the kernel lspci to see the graphics card; the only VGA controller it acknowledges is the integrated one.Running dmidecode acknowledges the existence of an x16 PCI Express slot, and it says
Current usage: Unknown
There is an additional BIOS setting called "Internal Graphics Mode" which is normally set to "Auto" which means it is supposed to prefer a PCI Express VGA card. I set it to "Disabled" which now means I'm getting no output at all. I will soon be learning how to do a BIOS reset!
Other information: The PCI-E card is a MSI N210-MD512H GeForce 210. This is a fanless card. Although there are no fans to see turning, the heat sink on the PCI-E card is definitely getting hot, so the card is getting some sort of power.It gets all its power from the PCI-E slot; there is no external power connector.The BIOS is an AMI Award BIOS.how can I make the PCI Express graphics card visible to Ubuntu?
View 1 Replies
View Related
Feb 7, 2010
I have an Acer 1200X with an Nvidia 8200 graphics GPU integrated on the motherboard. I have an HDMI and VGA output. I have downloaded the Nvidia graphics driver using envyNG and the old fashioned way. I have tried configuring the monitors 15 ways from Sunday in the configuration and I cannot for the life of me get dual monitors to work.
When I go into configuration with the Nvidia wizzard it blanks like its going to work then just stays black with the mouse cursor. I also cannot save as I get a "parsing" error. I am using Ubuntu 9.10 and have even tried using envyNG to get the monitors to work on twinview... NOTHING Hope someone can help!
My dad who is a Linux nut came over to help and he left 3 hours later because were tempted to chuck the computer out the window...I need to figure this out as this is going to be my work computer and I need dual screens.
View 1 Replies
View Related
Feb 23, 2010
we have installed centos in our organisation on vitual box.it gives display only in the middle of screen.i want to set it on full screen. when i select full screen option the back black screen become full but the display is same. how can i adjust it on full screen?
View 2 Replies
View Related
May 1, 2011
I'm getting random system hangs and display issues when using my computer with my nVidia graphics card. On a lark, i checked /proc/interrupts and noticed that the nvidia device is sharing an interrupt with one of my USB boards, as well as my integrated sound card. i managed to move my sound card by editing my alsa-base and adding:
Code: options snd-hda-intel enable_msi=1 This helps mostly, but i'm still getting intermittant issues. is there any way to shift the interrupt of my gfx card (or usb controller) to avoid this potential conflict? i know the devices should be able to co-exist, but i've seen several people having issues when an nVidia card shares interrupts.
[Code]...
View 1 Replies
View Related
Aug 8, 2010
im installing ubuntu onto a friends ibook, but am first running it live off the disk. it runs well, except for one thing, the display has a problem,i guess it seems like its tiled on the monitor, instead of fullscreen, it has a full desktop taking about 2/3 of the monitor, a sliver of the same desktop right below it, and a line of black to the right.
View 6 Replies
View Related
May 31, 2011
I am working on a gym class display screen which was built by others. It is operated under Ubuntu. Everytime I click on Firefox, the page goes to fullscreen, but the problem is that the gym class display is not zoomed to full screen (which is what we need). there are black blank parts on both the right and the bottom of the screen.There is no shortcut key working under firefox either, which means I can't zoom the screen or even enter url for any websites.I checked the gym class website on my computer, everything looks perfect. I think there must be some setting wrong on the operating machine.
View 3 Replies
View Related
Feb 26, 2010
Mobo - Asus M4A78T-E
CPU - Phenom II X4 955
RAM - DDR3 1333 dualchannel 8G
Display - Samsung 2494
Debian 504 64bit
Where can I download respective drivers. Linux drivers coming with the mobo can't work. There is no driver for Linux on the CD coming with the display. Fonts becomes very large even selecting "8". The screen can't expand to the full size of the display.
View 2 Replies
View Related
Sep 26, 2010
I know that you can make it full screen, however it just makes the background OS's background black, and still provides a smaller display. Is it possible to make the guest OS's screen (or display) full size?
View 6 Replies
View Related
Aug 29, 2010
where i can find a driver for Multimedia audio controller: nVidia Corporation nForce2 AC97 for Linux
View 5 Replies
View Related
Aug 24, 2010
I'm using a lenovo notebook with switchable graphics (Intel HD and ATI Radeon 5650), and I'd like to have Ubuntu use the integrated graphics, but I can't figure out how. The BIOS has two graphics options: switchable and discrete. On discrete just the ATI card runs, but on switchable, it seems like both cards are being used. Is it possible to use just the integrated graphics?
View 8 Replies
View Related
Jul 2, 2010
I tried installing 10.04 via Wubi on a friend's notebook and have hit problems with the display. The installation seemed to proceed OK (took ages to download / install - left it running overnight) until it came to boot to Ubuntu. The GRUB menu appears OK, but choosing Ubuntu leads to a blank screen with some icons at the bottom, which is displayed for a few seconds, then the (login?) screen just shows rolling display, like an out-of-tune analogue TV. I suspect that I need a graphics driver or something? The notebook is a logiQ notebook, with 128MB SiS Mirage-3 graphics.
View 2 Replies
View Related
Dec 15, 2009
I am new to this forum. I am a both rhel5 and fedora user.I can not configure my Samsung syncmaster 632nw monitor to display full screen at 1360X768.There is huge blank space on left and right portion of the monitor.The maximun resolution is 1024*768 and minimum is 640*480.
I have tried many times to solve it using xorg.conf but still unable to do it.
Here is xorg.conf's content :
View 5 Replies
View Related
Sep 26, 2010
Recently I upgrade to the latest Nvidia driver for Linux. I checked that it was compatible with my Ubuntu 10.04 x64 system and my geforce gt 220 graphics card. I decided to go with the newest beta ver 260.1904. Installation went well, better actually than other times I tried to install the newest driver from their site. After installation was finished I restarted and let my system load up. As soon as it got past the ubuntu logo, the screen just went blank as if there was no signal.
I determined that everything but the display was working. When I pressed ctrl-alt-F1 the numlock light turned off (this usually happens) and was still toggle-able. When I went through the other x-servers (ctrl-alt-(F2-F6)) the light went out but could be turned off and on by hitting numlock. When booting in from recovery mode, the screen displayed up to the point where it would show recovery options with no noticeable error showing before the screen turned off. This is what worries me the most.I don't think it is my Xorg.conf because I replaced with a backup and still have the same problem.Does anyone have any ideas about why this is happening or how I can at least see the terminal. As a side note, its definitely not the card because the card worked fine before, works in windows and live cds, and I tried with an older nvidia card and had the same problem.
View 3 Replies
View Related
Jul 18, 2010
OpenSuse 11.3 with nVidia drivers.I have the screen working fine though it only runs in 1600x1200@75 using the nVidia driver (GTX260 card).When I play a game in full screen mode all seems OK but when I exit the game then I just get the mouse pointer on a black screen.There must be something present since the cursor changes as I move it, normal pointer -> hand over a link etc. It's just that black on black isn't very readable.
View 5 Replies
View Related
Sep 1, 2011
in ubuntu land i have been thinking and i have intergrated HD graphics on my craptop i bought it for my study so it doesn't really matter but my theoretical max graphic memory is 3GB and i am only using 128 MB now has any one figured out a way to alter the default ;/. im sure it is possible to increase processing power form the split with CPU to but im sure acer have locked such capability.
View 5 Replies
View Related
Apr 11, 2010
After a PSU and motherboard failure, I'm about to spec out a new PC. The last time I looked, Nvidia was the preferred graphics chipset as they tended to support Linux better than ATI. Is this still the case?[url].... seem to have lots of ATI cards in stock but hardly any Nvidia (despite offering a similar sized range), but I don't want to get an ATI card if it's not preferred for technological reasons (or even FOSS ethical reasons!).
View 9 Replies
View Related
Jun 6, 2010
After having some trouble with Intel graphics I decided to pick up a PCI Nvidia graphics card. Now I am wondering what driver to use. Is the open source drive good enough to use or should I install the Nvidia driver? I know that things are generally easier with the default driver, especially for support on older cards, but I would like to get the best performance I can. This is for my Dad's computer, so he won't be playing any games, but if it will help with 2D and video that would be great.
The card is an Geforce FX5200 fanless card, I've heard they are well supported in Linux.The computer is a P4 Dell 3000 with Ubuntu desktop 10.04 32bit.
View 2 Replies
View Related
