Ubuntu Multimedia :: Closed NVIDIA Driver Not Working / Solve This?
Feb 12, 2011
I'm trying to get a fresh install of Ubuntu 10.10 working with the closed Nvidia driver, as I would like to get the HDMI output working.
I have a Sony Vaio VPCCW18FX, with a Nvidia GT 230M graphics card. The open source nouveau driver works fine, but does not run smoothly. The only problem here is that it's needed to run with "nomodeset".
If i just activate the Proprietary Nvidia driver and reboot, it will hang after writing "Checking battery State [ok]". I have tried to add EDID from Windows partition, and here it hangs at a blank black/grey screen. I have tried hooking up an external display, no output on it either.
I installed it on a Dell Inspiron 531 with the GeForce 6150SE nForce 430 built in video card. From the recommend driver list I installed �NVIDIA accelerated graphics driver (version current) [Recommended
Well, turns out it should not have been recommended. I had restarted and all I got was a low res ubuntu logo and a boot right into a full screen terminal. Tried startx and got a no screens found, I look online for about an hour last night and decided to just reinstall, which takes a couple hours when installing all the packages.
I have done more research today and found to install the latest linux x64 driver from nVidias website, which I did, but it does not run. I followed some more instructions and it said to do a �sudo chmod +x <file>� which I did, and it starts to open and I get �You appear to be running an X server; please exit X before installing.�
I�m starting to get a little frustrated here, guess I�m just used to a lot of the ease of windows and assumed that something like installing a graphics card driver would be easy.
I upgraded to 10.10 from 10.04, and I noticed that the nvidia driver are not working all well as they did before.
Although I get the nvidia logo when X starts, the 3d part does not work well. For example using mplayer -vo gl does not work anymore. When I type glxinfo I get the x error of failed request badwindow message. More anonyingly flash will crash when going to fullscreen.
The 2d part of the drivers seem fine because xvinfo and -vo xv works fine.
I used Gefoce9400GT , 190.53 nvidia driver, configuring Mulitiple X screen both CRT and TV, work fine if CRT and TV connected to card, but I hope foce TV-out output signal, means that if not connected to TV, the SVIDEO can output signal. Because the line too far, cannot detect TV connection, so I think foce output TV-out signal. I used Option "ConnectedMonitor" "CRT, TV". Can force found 2 display device, have 2 screen ok, but not display at TV if not connected TV. I do not understand why the TV has been forced output signal does not display images, they can be connected to the TV show?
I am running the newest Nvidia driver from nvidia.com, version 260.19.44. The built in proprietary Nvidia driver does not work properly.
Recently ubuntu was updated to a newer kernel 2.6.35.27 from 2.6.35.25. Under 2.6.35.25 the driver is working. Under 2.6.35.27 the desktop is not starting, and I can login to a 'console'. After login i try to run startx, and gets some errors. See attached Xorg.0.log.
I have a Dell XPS M1330, which has a GeForce 8400M GS GPU. The binary (sigh) nVidia driver installed is version 190.53 (installed by sgfxi). This is working well: glxgears gives me about 2600 FPS and compiz is happy.An old Philips 170B is attached by VGA cable. I was looking to set up a method of switching resolution upon connecting to the monitor when working at the desk, since I don't like the 1280x800 resolution of the laptop.
nfortunately, I can't get any output on the external monitor. It does work under Ubuntu, which installed the 180 series binary driver. (Going to an earlier driver is an option, but I want to understand the problem.) Bottom line, I want to work under Debian.As far as I know, nVidia's proprietary driver doesn't support xrandr. At any rate, with he external 170B monitor attached and turned on, I get the following:$ xrandr -qScreen 0: minimum 320 x 175, current 1280 x 800, maximum 1280 x 800default connected 1280x800+0+0 0mm x 0mm
i installed the new beta 10.04 and it seemed right after the install and update that both nvidia hardware drivers were automatically install together. i deactivated both drivers. one driver showed the nvidia 173 driver and the other one showed "current" nvidia driver.
after a restart i then tried to activate the 173 driver. system required a restart. so i did. system booted to a black screen. i believe its at the desktop but i am unable to see it. i tried to hit esc at the boot screen to enter the grub menu but that didnt work.
Currently using Nvidia driver version 195.36.31, it's the version that works with Nvidia-kernel-dkms, would updating Nvidia driver to the current 275.09.07 driver version break my setup?
Pretty self explanatory, I can't get the NVidia driver to work with my laptop's 310M. And yes I have tried both steps in .64&postcount=9, but to no avail. The two error messges I'm seeing are "(EE) No devices detected." and "Fatal server error: no screens found".
I had to have the Nvidia Driver build a module to my kernel. It goes through, says it was successful, but I an unable to start X and get this log:
Quote:
X.Org X Server 1.6.1.901 (1.6.2 RC 1) Release Date: 2009-5-8 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.18-128.1.6.el5 i686
[code]....
Its an Nvidia 8200 integrated graphics card... Not sure if there is a wrong driver or the driver is in a different location then where Fedora is looking.
My problem started with the following post.[URL]I ended up tracing the issue back to openGL that disappeared during an update and the nvidia driver had broken. The only remaining issue is that the 3D acceleration on the NVIDIA (GeForce 8600 GT) card will not activateURL]hich I have done many times now. I am now on the nvidia-173 driver as that one seems to be working the best. Even the nvidia-settings is having trouble and crashes when I try to look at the OPENGL/GLX information.I have found many instances of jockey showing that the driver is "active but not in use" which is what I am seeing. The problem is that the 3D acceleration is not working and the issue seems to be the driver.
I recently downloaded and installed Ubuntu 10.10. I thought it was awesome...still do. OK, the problem is i was prompted to install some proprietary drivers and so i did but thats when the problems started. After reboot i couldn't get the GUI or gdm (not sure what to refer it to) to work. It goes directly to a terminal screen every time so i actually reinstalled Ubuntu and tried installing the drivers all different ways but no luck. i also can get into recovery mode and do low graphics. the driver version im trying to get working is nvidia 260.19.12. my graphics card is a geforce 7 series cant remember the number i have a 32bit processor.
my laptop is ASUS U41JF with Intel Core i3-380M and nVIDIA GeForce GT 425M, everything on my Slackware64-current is fine except the video driver.I have tried both ways:1. Packages from Slackbuild(260.19.29)2. Driver from nvidia offical website(260.19.36)Both methods fails because the screen turns black when I set nvidia driver in xorg.conf ans start X. The laptop even stops responding with the second method.The followings are my xorg.conf and log of XorgQuote:
I'm trying to create a flash drive that I can use on my laptop to boot into ubuntu. I followed the instructions on the download page to create le usb drive and was successful.My problem is that whenever i install my nvidia drivers, my internet completely stops working. Both wired and wireless work fine on a fresh install. I can reboot and try again and they both still work. While installing the nvidia drivers however they both stop working, and upon a reboot they still aren't working. I can connect via my desktop and my phone to the same access point i'm trying to go through on my laptop, so the problem is isolated to my laptop.
I used leighs post to install the nvidia driver for Fedora 12 and now plymouth does not work it uses the text theme. Right before it goes into the text theme I get this message:
To use games and other intensive applications, but with the switch I completely lost control of the brightness for the monitor. Is their a way to configure that, through the terminal or external application. If not, is there an experimental 3d version of nouveau I could try. Help would be appreciated, everything else works great so far.
About a month ago, I decided to go deeper in my Linux knowledge. I've been reading a lot and found out that Arch linux would be my learning distro. As I was installing Arch, it was a pain at first but I really learned a lot which I would never ever learn with Mint. Now I decided to take a step further is which "compiling your own kernel".
MY PROBLEM:
Everything was smooth in my Arch for a 2 weeks until I decided to compile my own kernel. I currently have a Nvidia GTX 460 1GB card.
BTW, the method I used to install nvidia with 2.6.37 was
Code: pacman -S nvidia nvidia-utils and that worked with all of the .37 kernels (-1 -2 -3 -4) which was download from kernel.org.
When I compiled the .38 (using the same .config of .37), it just boots up to the terminal (not loading gdm). However, I could still login by typing my username and password. So I've checked dmesg of both .37 and .38 and noticed that the Nvidia driver is not loaded in .38.
I tried reinstall it by running pacman and it doesn't do anything. It was thinking of uninstalling nvidia and nvidia-utils but there are so many dependencies conflicts (like screensaver, compiz, etc).
Since, I didn't want to mess up my .37 install, I just grabbed an old HDD and installed from scratch again. This time, I compiled the .38 kernel first (without gui) and then installed nvidia nvidia-utils. It was the same problem.
With this observation, I'm concluding that the nvidia and nvidia-utils from pacman is not compatible with .38.
I've read that I have to wait for nvidia to release a driver that will be compatible with the .38 kernel. Is that true? Does it mean I have to wait for nvidia/nvidia-utils to be updated from pacman? How would I know when it is updated?
I've also read about nouveau, but I guess that is not for me because it doesn't support 3D.
Is there a work around for me to use nvidia/nvidia-utils with .38?
Is nvidia and nvidia-utils proprietary drivers? What is the difference with these two and the one you download directly from nvidia?
First of all, I apologize for the bombardment of questions. As you can tell, I'm so clueless on how nvidia drivers work on linux in general (since it was spoon fed by mint) and I really would love to learn about this is a deeper level. Could someone please explain to me (LAYMANS terms) how nvidia works (and possibly a solution to my issue).
EDIT: Additional info - I have a netbook that also runs arch. It uses an Intel GMA integrated video chip which I used "xf86-video-intel" from pacman and I believe since it is open source, it works with .38 fine. So does that mean if you use an open source driver, it will work with all other kernels?
I have installed the Nvidia drivers on my desktop using [URL] according to the Debian way. Everything seems to be fine except the resolution. The best it will let me choose is something like 600x480. I have searched and most of what is suggested around the web is to change xorg.conf. I have tried this using different setting suggested but nothing is working. I did not have a xorg.conf file so I created one with the setting suggested on the Debian wiki.
I am using the akmod nvidia driver and I have the option for "sync to vblank" checked, however when running minecraft my computer is still pulling 200+ fps and it's causing tearing like a beast.Is anyone else having this problem? I don't know if my drivers are corrupted, set up improperly, or if the driver is just broken.
I've installed 9.10 and wish to use the nvidia-glx-173 driver as recommended by jockey. Using the jocky GUI just hangs at 100% cpu, a significant portion of which is the cdrom process; I've tried installing the package directly in aptitude and get the error:
Code:
Media Change: Please insert the disc labeled 'Ubuntu 9.10 _Karmic Koala_ - Release i386 (20091028.5)' in the drive '/cdrom/' and press [Enter]. The installation disc (standard x86 disk from shipit) doesn't satisfy it. How do I get aptitude to just download it from online repositories?
I have a Zotac IONITX-F-E motherboard (Intel Atom Dual Core 1.6 GHz + Nvidia ION) -based box with Ubuntu 10.04 64-bit installed. My goal is to play back 1080p video. I read somewhere that the nouveau driver that installs by default with ubuntu 10.04 does not support VDPAU. So, my first step is to install the nVidia proprietary driver. I tried following a half-dozen different guides for doing this, none of which worked. Let's take this one for example: [URL] I purge. I reboot. I run the Nvidia installer (NVIDIA-Linux-x86_64-195.36.24-pkg2.run). I get:
Code: ERROR: Unable to create '/usr/lib/nvidia-current/libGL.so.195.36.15' for copying (no such file or directory). So, I run: Code: sudo apt-get install nvidia-glx-185 nvidia-185-modaliases I try the nvidia installer again. It works. I reboot. I get a message saying that ubuntu is running in low graphics mode, because loading the nvidia kernel module failed. I check /var/log/messages and see: Code: API mismatch: the client has version 195.36.24 but the kernel module has version 195.36.15. I take a Tylenol and here I am.
I just performed a clean install of Kubuntu Lucid earlier this week after deciding it was time to upgrade from Hardy. Pretty much everything worked, until I attempted to install the proprietary NVIDIA driver.
OS details: Kubuntu 10.04 x64 Kernel 2.6.32.22.What happened when I tried to install the proprietary nvidia-current package was simply that it didn't work. I could open the nvidia utility, it would say the driver was not in use. Attempts to force the issue by running nvidia-xconfig would render the X server unable to start, which gave me some quality time in a shell console with APT or restoring the xorg.conf file from backup. Trying to compile and install the driver from nvidia also wasn't working out so well.
I think the issue boiled-down to the install presumably attempting to upgrade the kernel during initial install from CD, but not doing so completely. I had all the appropriate 2.6.32.22 kernel and header packages, but GRUB was apparently still booting to the 2.6.32.21 kernel (which had no headers or anything) and not giving options to boot to the upgraded kernel.
How I fixed this was to remove all packages related to the 2.6.32.22 kernel via APT, then remove all the 2.6.32.21 kernel packages. That second operation triggered the 2.6.32.22 kernel to be reinstalled, and GRUB to be configured correctly to boot to it. At that point, I reinstalled nvidia-current, and it worked. I tried this after determining I was on the 2.6.32.21 kernel, and had no option to boot to the 2.6.32.22 one.
Your mileage may vary. In retrospect, I probably could've fixed it by fixing GRUB to boot to the current kernel. This appears to be a consistent issue, as I reinstalled at one point, just to start over, and went through the same thing again.
I suspect the driver I obtained from the nvidia website and patched (due to issues it has with recent kernels) might work now that I'm booting to the correct kernel with headers, but I think I'll save that for another time since nvidia-current is working great for me at the moment.
I wish to update my nvidia driver (I was running 195.36.24 and I want to update to 195.36.31). I followed all the instructions on this thread (http://ubuntuforums.org/showthread.php?t=1467074) and everything went well until this part:
Code: sudo sh blahblah.run
The error I get in the terminal reads: You appear to be running an X server; please exit X before installing. For further details, please see the section INSTALLING THE NVIDIA DRIVER in the README available on the Linux driver download page at [URL]...I have no idea how to exit X as it's not in my system processes.I have updated my nvidia driver in the past but have never encountered this problem. I'm running Ubuntu 10.04 on a Dell XPS M1530 if that matters.
[URL]. I now have both monitor working and noticed my drivers are not current. I have the older ones installed. The 260.19.06 one. I installed via the suggested restricted driver utility in ubuntu 10.10. I don't have full use of the graphics and would like to install the latest driver.
Question: 1. Do I uninstall nouvea and nv drivers (still installed) 2. Do I uninstall the current nvidia driver, then do a manual install of the latest driver from nvidia?
Installing Mythbuntu 10.10, which I finally got installed properly. At first I installed the open-source video drivers just to make sure the installation worked, then I installed the "version current" proprietary drivers using the graphics drivers manager...tool...thing. However, when I restarted the computer, it has a text-mode splash screen and I stay in the first virtual terminal.
If I try to go to the GUI "terminal" [Ctrl-Alt-F7], it appears to be partway through some kind of check:
Code:
I ran sudo dpkg-reconfigure xserver-xorg to try to get back to the open-source drivers, but it didn't give any text output and went straight to the next line of command prompt, when I restarted it did the exact same thing. Any tips for at least getting back to the open drivers? I'd like to not have to reinstall again (I'm dual-booting WinXP,). The card in question is a GeForce 6200 AGP.
My ubuntu 10.04 64 bit system uses the nvidia driver 195.36.24. I do not remember installing it, but I must have installed it using "official channels".In fact, the package nvidia-current is installed on my system.What is the cleanest way to upgrade to a later version of the nvidia driver? I need to do this in order to run a CUDA 4.0 enabled application. Minimum driver version I need: 270.41. I'm willing to ditch Ubuntu 10.04 if necessary.
what the prepackaged proprietary nvidia driver is missing to run compiled OpenCL programs.
I have the pre-packaged proprietary nvidia driver from [URL] and the package is missing some files, like lobOpenCL.so, which I extracted from the .run file and put manually in the /usr/lib64 directory toether with creating some symlinks. I can compile my opencl programs fine (C | // // File: hello.c // - Anonymous - 3BF2vDzc - [URL], Getting started with OpenCL and GPU Computing), but when I run, the firsr opencl-related function clGetPlatformIDs returns an error code.
Again, I try to figure out what the prepackaged driver is missing. If I use the nvidia .run script driver, the problem probably does not exist. CUDA executables run fine (compiled on an other opensuse machine without nvidia card)
opensuse 11.1 64bit, nvidia quadrofx3700 driver version 256.53
