Ubuntu Multimedia :: Unable To Use The Nvidia Driver
May 28, 2010
I just performed a clean install of Kubuntu Lucid earlier this week after deciding it was time to upgrade from Hardy. Pretty much everything worked, until I attempted to install the proprietary NVIDIA driver.
OS details: Kubuntu 10.04 x64 Kernel 2.6.32.22.What happened when I tried to install the proprietary nvidia-current package was simply that it didn't work. I could open the nvidia utility, it would say the driver was not in use. Attempts to force the issue by running nvidia-xconfig would render the X server unable to start, which gave me some quality time in a shell console with APT or restoring the xorg.conf file from backup. Trying to compile and install the driver from nvidia also wasn't working out so well.
I think the issue boiled-down to the install presumably attempting to upgrade the kernel during initial install from CD, but not doing so completely. I had all the appropriate 2.6.32.22 kernel and header packages, but GRUB was apparently still booting to the 2.6.32.21 kernel (which had no headers or anything) and not giving options to boot to the upgraded kernel.
How I fixed this was to remove all packages related to the 2.6.32.22 kernel via APT, then remove all the 2.6.32.21 kernel packages. That second operation triggered the 2.6.32.22 kernel to be reinstalled, and GRUB to be configured correctly to boot to it. At that point, I reinstalled nvidia-current, and it worked. I tried this after determining I was on the 2.6.32.21 kernel, and had no option to boot to the 2.6.32.22 one.
Your mileage may vary. In retrospect, I probably could've fixed it by fixing GRUB to boot to the current kernel. This appears to be a consistent issue, as I reinstalled at one point, just to start over, and went through the same thing again.
I suspect the driver I obtained from the nvidia website and patched (due to issues it has with recent kernels) might work now that I'm booting to the correct kernel with headers, but I think I'll save that for another time since nvidia-current is working great for me at the moment.
View 4 Replies
ADVERTISEMENT
May 28, 2011
I recently installed Ubuntu 11.04 on my Emachine Er1402-05, Wireless works fine, but not the grahics Emachine Er1402-05 has a nVidia GeForce 8200 graphics card. The problem is that after installation it only support resolution upto 1024x768, while my LCD has native resolution at 1600x900. I have installed the most recent nvidia driver $sudo apt-get install nvidia-current However, I was not able to config it:
$ sudo nvidia-xconfig
sudo: nvidia-xconfig: command not found
I was not able to install the package.
$ sudo apt-get install nvidia-xconfig
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Unable to locate package nvidia-xconfig
[code].......
View 9 Replies
View Related
Apr 22, 2010
i installed the new beta 10.04 and it seemed right after the install and update that both nvidia hardware drivers were automatically install together. i deactivated both drivers. one driver showed the nvidia 173 driver and the other one showed "current" nvidia driver.
after a restart i then tried to activate the 173 driver. system required a restart. so i did. system booted to a black screen. i believe its at the desktop but i am unable to see it. i tried to hit esc at the boot screen to enter the grub menu but that didnt work.
View 3 Replies
View Related
Jul 7, 2011
Currently using Nvidia driver version 195.36.31, it's the version that works with Nvidia-kernel-dkms, would updating Nvidia driver to the current 275.09.07 driver version break my setup?
View 3 Replies
View Related
Mar 4, 2010
This is my first day with Umbuntu and my first post here at the forums. I bought a Dell Pentium 4 with a fresh install of Umbuntu 9.10 on it. Worked well until I decided to do something a newbie shouldn't do and install a graphics card and drivers. The graphics card worked just fine until the drivers were installed and I tried to reboot the system. Now it no longer boots. Some specifics for you.
Since my time with Ubuntu is limited to hours, the nomenclature will probably be wrong. But I will try to get the point across. The card is a EVGA GeForce FX 5700 Ultra. On first start up with this card the computer functioned fine. I went to a place where you could change the screen options. There were three selections and I don't remember the names (idiot that I am). I selected the middle one. The OS stated that in order to utilize all the capabilities of nvidia graphics cards blah, blah, blah, a driver would need to be downloaded and activated. No name, just a driver. OK, do it (sounds kinda windows like). The download seemed to go OK, but now I needed to reboot to activate the driver.
Now: Ubuntu logo comes up. Screen goes to a text screen that says:
Ubuntu 9.10 dave-ubuntu tty1
dave-ubuntu login:
This screen flashes and does not take input from the keyboard or mouse. Next, I removed the graphics card and used the on-board graphics. Same result with faster flashing. What have I done? Apparently Ubuntu and Linux in general don't have a system recovery option? I read something about the GRUB menu, but the system flasher GRUB loading for half a second and then is on to locking up. I can't seem to get to a GRUB menu. What a way to finish the day.
View 9 Replies
View Related
Dec 19, 2008
I recently reinstalled Debian on my desktop to migrate to 64-bit. Everything was working swimmingly before but I've encountered a bizarre error i have never seen before. After installing the Nvidia driver and rebooting when X comes up it complains it cant find any screens. However, if I kill X and start it again it starts with no issues. I also have an odd message at startup which might be part of the problem as well.I'm running Debian Testing AMD64 with and Nvidia 9800 GTX+. I compiled 2.6.27.8 for the install.
For what its worth the Nvidia module is showing up for lsmod so I don't really know what is wrong. I have tried reinstalling the nvidia driver as well which didn't help. The error message during bootup is:
Code:
Loading kernel modules...Usage: modprobe[-v] [-V] [-C config-file] [-n] [-i] [-q] [-b] [-o <modname>] [ --dump-modversions ] <modname> [parameters...]
modprobe -r [-n] [-i] [-v] <modulename> ...
modprobe -l -t <dirname> [ -a <modulename> ...]
[code]....
View 5 Replies
View Related
Oct 3, 2009
My system specs are..
OS: Fedora 11
CPU: Core2Duo E6750
GPU: Nvidia GeForce 9500gt
MOBO: A-Bit IP35-E
Now, i had an ATI Radeon x1950 and was using the open-source drivers with Fedora 11 and worked fine apart from maximum resolution was 1024x768. So knowing that Nvidia's Linux support was far superior i shelved out on a new GPU the GeForce 9500GT. I tried "yum install kmod-nvidia" - restarted and then the system loads using the nouveo drivers... So i blacklisted the nouveo drivers and changed the xorg.conf file to use the nvidia driver. Restarted, now its using the vesa driver! Blacklisted the vesa driver and after restarting its still picking up the vesa driver! So... i then head to nvidia's site, download the latest driver from there, shut down X-Server, installed them, restarted..... and still using the blumin vesa drivers!
View 4 Replies
View Related
Oct 15, 2010
i tried to go threw this by some tutorials on the wiki but without success. i all the time got this error: Nvidia log: [URL].. even if i ran the make oldconfig && make prepare command..
View 8 Replies
View Related
Feb 16, 2010
I installed openSuSE 11.2 three days ago, the first time, and have been trying to get the nvidia video driver to work ever since. So far, no luck. I have a dual-boot system with Windows 2k (legacy programs) and the graphics card works fine there, so the problem isn't hardware related. The nv driver also works under 11.2, but not well.The graphics card is a GeForce 6200, and the computer is an old Tyan Thunder S2885 with dual Opteron processors. I'm in 64 bit mode for the Linux install.
I've tried installing the video drivers by:Doing a fresh install, loading in the nvidia repository, then doing online update. The two nvidia drivers were loaded (nvidia-gfxG02-kmp-desktop and x11-video-nvidiaG02), but when I tried to reboot I end up with a blank screen and no sync to the monitor (Hitachi SuperScan Elite 751 CRT type). Rebooting in safe mode brings up the nv driver, which works. Doing a fresh install, doing online update,then loading in the nvidia repository, refreshing it, and installing the same two RPMs . . . with the same result. Doing a fresh install and using the "one click" install from this web site. Same result.
Doing a fresh install, doing online update, selecting the pattern "Linux Kernel Development" and installing it, downloading the Nvidia installer NVIDIA-Linux-x86_64-190.53-pkg2.run and installing it. Same result.
Same as above, but then using Sax2 -r -m 0=nvidia, even though Sax is depreciated. Same result. I've tried modprobe nvidia. Nothing. Over the last two days I've probably tried several other iterations as well, and forgot them, but nothing worked, it's always the same result.
Another weirdness, when I have YaST do "Hardware Information" it has no trouble identifying the monitor a getting it's info, but when I click the Display icon on the panel it tells me that it can't identify the monitor.
Here's the basic system info:
Code:
Directory: /home/BillyDoc/Desktop
Tue Feb 16 09:21:23 CST 2010
BillyDoc@linux-k7w3:~/Desktop> lsmod | grep nvidia
nvidia 9647368 0
BillyDoc@linux-k7w3:~/Desktop> su
[code]....
I'm definitely a novice to this sort of thing, and at this point I haven't a clue what's going on. It looks like the nvidia driver get's installed alright, but X simply doesn't know it's there. Oh, and another thing. When I go into YaST to look for the "Graphics Card and Monitor" program . it's missing! I assume this is because Sax is depreciated, but what's the substitute?
View 9 Replies
View Related
Mar 9, 2011
I installed the Nvidia driver for the on board GeForce 7025 / nForce 630a the "Debian way", according to this link Debian Nvidia Howto. The problem is that the only available screen resolutions are 640x480 & 320x240 and I need something more like 1024x768. The driver is installed correctly, or at least is properly recognized, as in Nvidia Xserver settings, GPU0 appears as GeForce 7025 / nForce 630a.
Here's the xorg.conf file.
Code:
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
[code]....
..only causes gdm not to start.On my Ubuntu partition, I have working the proprietary Nvidia driver (file: NVIDIA-Linux-x86_64-260.19.36.run), and have had no problems from it at all. I was going to install this same driver onto Debian when I read several pages advising to go the "Debian way".
View 4 Replies
View Related
Feb 10, 2011
I am not able to enable composite with the nvidia driver. And a few other issues that I been able to get around but so far the nvidia driver is my main problem.
View 21 Replies
View Related
Nov 3, 2010
I have been unable to find a driver for my nvidia geforce2 mx400. It's running in failsafe graphics mode. Does anyone know what I need to do to make it work? I'm a linux beginner, so please avoid jargon.
View 2 Replies
View Related
Sep 25, 2009
I was recently able to obtain a new laptop at work. Rather than reinstalling the OS, reconfiguring all of the software, and then copying over all of my data from my old laptop -- I decided to try to use dd to clone my drive. It worked pretty darn well (thanks Saikee!). However, I have two problems that I have noticed so far:
1) The system does not seem to offer me the option to install the proprietary nvidia driver. I was able to manually install the nvidia-glx-180 package and then edit xorg.conf appropriately and I'm running with the nvidia driver now. So this problem is resolved (though I still find it odd it didn't even offer my the "restricted hardware drivers" option in System -> Administration).
2) Wireless is not working. I checked dmesg and it doesn't seem to have any errors in it. Here is a list of things I have checked/found which I think might be relevant:
- Oddly enough it seems that my wired device always gets renamed from eth0 to eth1, and my wireless device gets renamed from wlan0 to wlan1. I'm not sure why (though I would prefer them to be eth0 and wlan0).
- dmesg output looks good shows some message about the wlan1 link not being ready
Code:
bmayes@bdmlin:~$ dmesg | grep wlan
[ 10.915831] udev: renamed network interface wlan0 to wlan1
[ 185.179556] bridge-wlan0: peer interface wlan0 not found, will wait for it to come up
[ 185.179559] bridge-wlan0: attached
[code]...
View 10 Replies
View Related
May 4, 2010
After upgrading kernel package to 2.6.32-5 NVIDIA installation gave me ERROR:Unable to load the kernel module 'nvidia.ko'. This happens most frequently when this kernel module was built against the wrong or improperly configured kernel sources, with a version of gcc that differs from the one used to build the target kernel, or if a driver such as rivafb/nvidiafb is present and prevents the NVIDIA kernel module from obtaining ownership of the NVIDIA graphics device(s), or NVIDIA GPU installed in this system is not supported by this NVIDIA Linux graphics driver release.
Here is /var/log/nvidia-installer.log:
nvidia-installer log file '/var/log/nvidia-installer.log'
creation time: Tue May 4 11:49:38 2010
installer version: 1.0.7
[code].....
View 12 Replies
View Related
Dec 4, 2010
I was running Fedora 13 on my old computer with a nvidia Geforce FX 5200 graphics card using the nvidia-173xx driver from fusion. After upgrading to Fedora 14 (the first day of its release) the X server wasn't working anymore, the screen just froze up after the progress bar. With Alt+F4 I "moved" to text mode and gave the startx command, but I got the fatal error message that there was no usable configuration detected. I deleted the xorg.conf file and afterwards I was able to start X again. I use the nouveau driver now, but it doesn't nearly work as good as the nvidia-173xx driver. I have it installed, but when I try to activate it (by running nvidia-xconfig as root) the X server doesn't work again after restart, and I have to do the same thing all over again.
View 6 Replies
View Related
Sep 29, 2010
In Fedora 13 with the kernel version of 2.6.34.7-56.fc13.x86_64, the NVidia driver of the version 256.53 was installed from rpmfusion repository. Everything works fine except for one problem: the brightness cannot be controlled from the power management programs in either KDE or Gnome. In Gnome, the scroll bar of brightness disappears, and, in KDE, the scroll bar cannot be dragged.
Since the computer with Fedora 13 and NVidia driver installed is Dell Studio One 19 (All-in-One computer) which has no hardware buttons to control screen display options at all, there is no other way to adjust the brightness of computer screen. The BIOS of the computer doesn't include an option to adjust screen brightness either. Since screen brightness is set at the maximum level when the computer is turned on, it is not possible to continue using the computer for a continuous period of time due to eyesight protection. Strangely enough, both the Nouveau driver included in xorg-x11-drv-nouveau 0.0.16-8.20100423git13c1043 from Xorg 7.4 and the driver included in the mesa-dri-drivers-experimental 7.8.1 support brightness adjustment without any glitches.
View 4 Replies
View Related
Jul 9, 2011
Infact I've seen the linux(ubuntu 11.04) for the first time today. I don't know anything about linux & i'm not able to install my nVidia 8600gt graphics driver. I've downloaded the .run file from here
[URL]
when I'm opening the .run file it's showing an error
"Could not open the file /home/f1/Downloads/NVIDIA-Linux-x86-275.09.07.run.
gedit has not been able to detect the character encoding. Please check that you are not trying to open a binary file. Select a character encoding from the menu and try again."
After trying for all day long I found this HOWTO
[URL]
View 2 Replies
View Related
May 12, 2010
So after getting around the Fakeraid bug, and the grub bug, and all the other bugs killing my system fixed and then i moved on to install my video driver. There was nothing in Administration>Hardware Drivers, so i downloaded the latest driver for my two 8600m gt cards. Did the whole ctrl+alt+f2 and then stopping xserver and then running the driver install only to run into yet another damn bug(see log below)
I have tried fixing it by doing what other threads have said to do e.g:[URL] still nothing. Below is the Nvidia log.
[Code]....
View 9 Replies
View Related
Aug 6, 2011
I had installed Ubuntu 10.10 and there was a dim spot on the left side of the monitor. I could move the window to the right, but anything on the left was dim, and if I set the window to full screen, the whole screen went dim. I was able to find a fix online, I followed the instructions, and Voila! It was fixed, so I knew it was not a hardware issue. I installed 11.04, and have the same dim screen issue, but I can't find the instructions that fixed it last time. I tried to download and install the latest driver from NVIDIA, and I get this error:
ERROR: You appear to be running an X server; please exit X before installing. For further details, please see the section INSTALLING THE NVIDIA DRIVER in the README available on the Linux driver download page at www.nvidia.com. If anyone has any fix for the dim screen
View 4 Replies
View Related
Aug 4, 2010
I am trying to update my Nvidia MX 480 GFX card. Today I figured out how to run the program as a root:
Code:
I run that and then this is what it gives me.
Where I got the link to download the nvidia driver from: [url]
View 9 Replies
View Related
Jun 15, 2009
I am a new user of Fedora 11. I am a Ubuntu user and could not get my GeForce 9100 on board graphics to work on my new computer with out crashing my computer so I decided I would try fedora. I downloaded the driver from NVidia and I am attempting to install it (Fedora didn't automatically find the driver). I get the following message:
"Error Unable to find the system utility 'ld'; Please make sure you have the 'binutils' installed. If you do have the bin utils installed, then please check that 'ld' is in your PATH."
I am running the driver from $Download as root. I don't know what ld or bin utils is or the check if I have it or if it is in my PATH.
View 9 Replies
View Related
Mar 20, 2010
I've installed 9.10 and wish to use the nvidia-glx-173 driver as recommended by jockey. Using the jocky GUI just hangs at 100% cpu, a significant portion of which is the cdrom process; I've tried installing the package directly in aptitude and get the error:
Code:
Media Change: Please insert the disc labeled 'Ubuntu 9.10 _Karmic Koala_ - Release i386 (20091028.5)' in the drive '/cdrom/' and press [Enter]. The installation disc (standard x86 disk from shipit) doesn't satisfy it. How do I get aptitude to just download it from online repositories?
View 1 Replies
View Related
May 19, 2010
I have a Zotac IONITX-F-E motherboard (Intel Atom Dual Core 1.6 GHz + Nvidia ION) -based box with Ubuntu 10.04 64-bit installed. My goal is to play back 1080p video. I read somewhere that the nouveau driver that installs by default with ubuntu 10.04 does not support VDPAU. So, my first step is to install the nVidia proprietary driver. I tried following a half-dozen different guides for doing this, none of which worked. Let's take this one for example: [URL] I purge. I reboot. I run the Nvidia installer (NVIDIA-Linux-x86_64-195.36.24-pkg2.run). I get:
Code: ERROR: Unable to create '/usr/lib/nvidia-current/libGL.so.195.36.15' for copying (no such file or directory). So, I run: Code: sudo apt-get install nvidia-glx-185 nvidia-185-modaliases I try the nvidia installer again. It works. I reboot. I get a message saying that ubuntu is running in low graphics mode, because loading the nvidia kernel module failed. I check /var/log/messages and see: Code: API mismatch: the client has version 195.36.24 but the kernel module has version 195.36.15. I take a Tylenol and here I am.
View 9 Replies
View Related
Jun 16, 2010
I wish to update my nvidia driver (I was running 195.36.24 and I want to update to 195.36.31). I followed all the instructions on this thread (http://ubuntuforums.org/showthread.php?t=1467074) and everything went well until this part:
Code:
sudo sh blahblah.run
The error I get in the terminal reads: You appear to be running an X server; please exit X before installing. For further details, please see the section INSTALLING THE NVIDIA DRIVER in the README available on the Linux driver download page at [URL]...I have no idea how to exit X as it's not in my system processes.I have updated my nvidia driver in the past but have never encountered this problem. I'm running Ubuntu 10.04 on a Dell XPS M1530 if that matters.
View 2 Replies
View Related
Oct 30, 2010
[URL]. I now have both monitor working and noticed my drivers are not current. I have the older ones installed. The 260.19.06 one. I installed via the suggested restricted driver utility in ubuntu 10.10. I don't have full use of the graphics and would like to install the latest driver.
Question:
1. Do I uninstall nouvea and nv drivers (still installed)
2. Do I uninstall the current nvidia driver, then do a manual install of the latest driver from nvidia?
View 5 Replies
View Related
Nov 23, 2010
Installing Mythbuntu 10.10, which I finally got installed properly. At first I installed the open-source video drivers just to make sure the installation worked, then I installed the "version current" proprietary drivers using the graphics drivers manager...tool...thing. However, when I restarted the computer, it has a text-mode splash screen and I stay in the first virtual terminal.
If I try to go to the GUI "terminal" [Ctrl-Alt-F7], it appears to be partway through some kind of check:
Code:
I ran sudo dpkg-reconfigure xserver-xorg to try to get back to the open-source drivers, but it didn't give any text output and went straight to the next line of command prompt, when I restarted it did the exact same thing. Any tips for at least getting back to the open drivers? I'd like to not have to reinstall again (I'm dual-booting WinXP,). The card in question is a GeForce 6200 AGP.
View 6 Replies
View Related
Jul 11, 2011
My ubuntu 10.04 64 bit system uses the nvidia driver 195.36.24. I do not remember installing it, but I must have installed it using "official channels".In fact, the package nvidia-current is installed on my system.What is the cleanest way to upgrade to a later version of the nvidia driver? I need to do this in order to run a CUDA 4.0 enabled application. Minimum driver version I need: 270.41. I'm willing to ditch Ubuntu 10.04 if necessary.
View 4 Replies
View Related
Feb 3, 2010
I have installed the recommended driver for my nvidia card (185), and after much fiddling finally got my config file to stick and boot correctly, however I can't see the output of the media player or the DVD player. The files play because I can hear them, but I don't see any output. I have moved the depth to 16 bit, but I still don't get anything.
View 3 Replies
View Related
May 20, 2010
I want to install new nvidia driver for geforce 8600 on ubuntu 10.04 but I recive the following error: The binuteals is not installed on the system.
View 1 Replies
View Related
Jun 6, 2010
After having some trouble with Intel graphics I decided to pick up a PCI Nvidia graphics card. Now I am wondering what driver to use. Is the open source drive good enough to use or should I install the Nvidia driver? I know that things are generally easier with the default driver, especially for support on older cards, but I would like to get the best performance I can. This is for my Dad's computer, so he won't be playing any games, but if it will help with 2D and video that would be great.
The card is an Geforce FX5200 fanless card, I've heard they are well supported in Linux.The computer is a P4 Dell 3000 with Ubuntu desktop 10.04 32bit.
View 2 Replies
View Related
