vsftpd is working fine in my network with anonymous user but i need to access that from out-side all the setting is done on the router. I am getting page to access ftp form out-side but only for ftp users not anonymous user how i will give permeation to access ftp to anonymous user ?
View 26 Replies
I'm trying to get vsftpd running with both anonymous and local user access to the same folder. The directory I'm using is /tftp with the following permissions:
dr-srwxrwx 7 root root 12288 2009-08-14 15:54 tftp
My vsftpd.conf is this:
anonymous_enable=YES
local_enable=YES
write_enable=YES
[code]....
I set the default "ftp" user's home directory to /tftp (was /var/ftp).
I am attempting to configure vsftpd to allow anonymous users to PUT files into a shared incoming directory. This would be like a dropbox for my customers. Ideally, the incoming directory's contents would not be viewable by the users.
I believe that refused connection is due to the PAM configuration for vsftpd.
May 4 08:03:16 WSVM-S1-1 sshd[1512]: Invalid user anonymous from xxx.xxx.xxx.xxx
May 4 08:03:16 WSVM-S1-1 sshd[1513]: input_userauth_request: invalid user anonymous
May 4 08:03:16 WSVM-S1-1 sshd[1512]: pam_unix(sshd:auth): check pass; user unknown
[Code].....
I have installed vsftpd by "yum -y install vsftpd",disabled anonymous login and set .When I use a linux client's file browser to login using a user account "ftpacc" by ftp://ip_address, its location is "/" instead of /home/ftpacc".When I use a window client to login, its location is "/home/ftpacc"
View 1 Replies View RelatedIn my house I have a small computer running ubuntu karmic that works as a server/media center.
I would like to have a folder (my ~/public folder) openly available to the entire world via anonymous ftp.
I have read somewhere that the defauld vsftpd config is basically this: no local user login, anon only and sharing a folder called /home/ftp, but I can't get this to work.
Here is my /etc/vsftpd.conf file:
Code:
obviously it's at least difficult but I'm interested in knowing if it's theoretically possible to allow anonymous users of vsftpd to upload to the same directory that anon_root is set to. If it's not then it's no big deal, I'm just trying to get a sense of the range of possibilities.
View 1 Replies View RelatedHope you can help me out. I'm trying to setup a "drop-box" on ubuntu 9.10 server with vsftpd. I'm able to login and land in the /home/user directory, however I cannot write anything.
View 5 Replies View Relatedhow to add files (and where) for anonymous download. I installed vsftpd and configure /etc/vsftpd.conf file...just few common options like allowing anonymous,download,upload. And now i can login with anonymous. But i dont know what to do next, i want to try to download and upload files.
View 9 Replies View RelatedI just want to configure Vsftpd to allow users to have total access to the FTP server. The server and users are all on a private LAN behind a router with no access from the Net, so I don't need any security. The following basic configuration doesn't allow uploading files after I log on as anonymous/whatever:
/etc/vsftpd/vsftpd.conf
Code:
listen=YES
anonymous_enable=YES
local_enable=YES
write_enable=YES
xferlog_file=YES
#anonymous users are restricted (chrooted) to anon_root
#anon_root=/home/ftp/incoming
anon_root=/var/ftp
anon_upload_enable=YES
anon_mkdir_write_enable=YES
#chroot_local_user=NO
#chroot_list_enable=YES
#chroot_list_file=/etc/vsftpd.chroot_list
Here's what happens when I log on as anonymous/whatever and try to upload a file:
> ftp server
Connected to server.
220 (vsFTPd 2.0.5)
Name (server:root): anonymous
331 Please specify the password.
Password:<whatever>
230 Login successful.
Remote system type is UNIX.
Using binary mode to transfer files.
ftp> ls -al
200 PORT command successful. Consider using PASV.
150 Here comes the directory listing.
drwxr-xr-x 3 0 0 4096 Mar 13 11:19 .
drwxr-xr-x 3 0 0 4096 Mar 13 11:19 ..
drwxr-xr-x 2 0 0 4096 May 25 2010 pub
226 Directory send OK.
ftp> put /var/tmp/ftp
local: /var/tmp/ftp remote: /var/tmp/ftp
200 PORT command successful. Consider using PASV.
553 Could not create file.
This is on Centos 5.3 by the way..... I had a DVD and, well, just wanted to test some things.. I'm aware that this is not the latest release.
And, by the way (I just read an earlier post) I've added the username and password with which I'm trying to login (..hello?).
I'm at work and I don't have a copy of my Vsftpd configuration file (don't wanna edit this whole thing - actually there is a copy, below). I've used Slackware for years and never had any issues with Vsftpd - it just works. I am trying Centos because I need help with upgrading my mail server (qmail) and there's not much help for Slackware users. Also, I used to run RHEL3 and had vsftpd working fine (had to copy some file to /etc/pam.d) but it worked famously. I compiled all my web server stuff (just don't like these default things where I have no idea how things are integrated) and I'm hung up on - of all things - vsftpd.
Anyway....When I try to log into my ftp server I get "KERBEROS_V4 rejected as an authentication type" and only the anonymous account works. Any other logins produce an error (incorrect login - see ya' later). I have SE Linux and the firewall OFF. I don't recall the directive, precisely, but my vsftpd.conf file is set allow local users to connect. I installed with yum and it added some lines at the bottom (one was about a user list and the other was about PAM). I've got a chroot list and a user list although it's not clear to me precisely where the user list should be placed. I actually uninstalled the RPM and compiled, too. I've done everything but call an exorcist. And I've found tons of posts regarding this on the net and none of the fixes worked. Man - on slackware you type "make" and "make install" (I build it with tcp_wrappers) and you're off to the races.
Actually - I did upload the vsftpd.conf file to work (where I'm at, now). Minus lines that were commented out it looks like this:
Could it, possibly, be something about how I am adding the user, the shell type, etc? I know that in Redhat I used to type "/usr/sbin/useradd -d /home/someuser joe". I've done it that way and I've also done it like so: "useradd -d /home/schmoe -s /bin/bash schmoe".
I've only recently encountered this problem with vsftpd when I was creating new ftp accounts. I keep on getting:
550 Access Denied.
on every action I try to do on ftp, no matter what. I've been trying to solve this myself however my attempts have been futile.
The permissions, and ownership have been checked and rechecked tens of times now, so thats not the issue. I've reinstalled the OS of my server twice now, and the problem is still persisting. Heres my config file, this isnt for anon by the way.
Code:
# Example config file /etc/vsftpd/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
[Code].....
I am using VSFTPD. I want to restrict access from perticular range of IPs. Ex: 172.10.*.* How can i restrict access to server from a range of IPs?
View 3 Replies View RelatedTrying to set up VSFTPD on the CentOS 5 box at work, which is an internal web development server. I'm leaving soon, and all knowledge of or desire to learn SSH is going with me so the other employees will need to be able to access the web root using FTP clients.
Essentially there is no need for special user accounts or privileges, it's an internal server in a tiny company. I've got the LocalRoot set to /var/www/ which I can log in to and read all files via FTP, however despite setting everything to 777 in /var/www/ and below, I still can't get any write privileges on the FTP server.
I have CentOS 5.5 distribution with Dom0 and DomU installed. I try to access Dom0 files during vsftpd server from DomU during ftp client. I successfully login with root and simple user, but when I try to list (or cd to some directory) in user home the SELinux prevent it from me. I get this in audit.log:
[Code]....
Seismicmike here. My first post. I'll try to be as clear and concise as possible. For the sake of this post, I'm going to use 1.2.3.4 as a place holder for my public IP. On my web server, I would like to be able to access the /var/ftp directory through a web browser. I have successfully done so with Google Chrome, but I cannot access the directory in Firefox or IE. Both FF and IE ask me for authentication but then time out attempting to load the directory.
I suspect that there may be something up with switching to passive mode and/or that this issue may be more with my configuration of Firefox and not with the server (seeing as how Chrome works). Another possibility may be related to SSL. When I connect with FileZilla, I have to use the FTP over Explicit SSL/TLS option in order to connect. In any case I still would like to fix it. I would also like to avoid having to install FireFTP if at all possible.
Steps to reproduce (not that you can without my actual IP =J):
* Open Chrome
* Go to ftp://1.2.3.4
* Enter username
* Enter password
[code]....
Any clue? I'm using the same key for root login and it works fine (also works fine for SFTP but i hate using that cause its extremely slow)
View 2 Replies View RelatedI have a test server (2.6.18-194.el5) that allows automated tools from Windows 7/Windows Server 2008 to access the filesystem (anonymous NFS access) via Samba (3.5.4-0.70.el5_6.1). Documentation on the smbusers file on samba.org seems a little thin.
* why is it necessary map unix users to samba users?
* what purpose does this mapping serve?
* does the umask of the unix user limit the samba user it is mapped to when creating files/directories? what about anonomous access?
* why are files created via anonymous access owned by 'nobody'?
* how can I control what user and permissions files/directories are created with?
I would like to configure an access to folder
/fileserver
for two services : Samba and VSFTPD
How to do it ? How to create folder rights that samba and ftp user will have an access (read/write/delete) to all directories in /fileserver.
My system is CentOS. I`m starting samba and vsftpd like a root (/etc/init.d/vsftpd start etc.)
Running Debian 5. I have a small server that needs to provide anonymous ftp service (download only) to the folks in my dept (we have a firewall that will keep outsiders out, so I'm not worried about outside folks getting to the files). The question is: which anonymous ftp server should I install? Something that can be installed via "apt-get install xyzzy", where I can edit the /etc/xyzzy.conf file to point to the /home/ftp directory, and start/stop it with /etc/init.d/xyzzy start|stop|restart command.
View 3 Replies View Relatedi'm using ftp server with RHEL-5.1 now i wish to an anonymous user can create and upload some file on my ftp server... for this i configure the entries in /etc/vsftpd/vsftpd.conf
anonymous_enable=YES
# Uncomment this to allow local users to log in.
local_enable=YES
[code]....
im using default setting for proftpd and having two major problem for me at least
1. how to disable anonymous login?
2. how to make proftpd login using my default box login?
I am unable to create a directory as an anonymous user using FTP. Settings are as below mentioned:-
vsftpd.conf
anonymous_enable=YES
write_enable=YES
anon_upload_enable=YES
[Code].....
I am trying to configure a ftp server (pure-ftp) where I am using CentOS 5.5.
View 1 Replies View RelatedI'm trying to use Nautilus's connect to server to connect to an ftp server, but I'm having a problem. The username on the ftp server is "anonymous", but it requires a password. When Nautilus sees "anonymous" as the username it assumes it's dealing with a public ftp server and doesn't prompt for a password, and then, of course, I fail to connect.
I've tried modifying the .gtk-bookmarks file to account for this, but this leads to another problem. The password opens with a / and for whatever reason, this leads to Nautilus popping up an error: "Could not connect to ftp://anonymous:0/[rest of password]@[server]". It's adding a "0" to the beginning of my password for some reason. Is there any way to fix this without changing the password?
I just opened an (unmanaged) VPS account and and have been encountering nothing but problems with trying to get Apache up and running (its something I've done many times before).Basically the inital error was with LDAP not having enough space, so I disabled the related extensions and Apache still would not run. Looking at the log, it contains: (28)No space left on device: Unable to create scoreboard (anonymous shared memory failure)
View 1 Replies View RelatedI'm trying adjust my proftpd server's settings, that anonymous users could download what they need smoothly.
A small problem made me so bemused:
In the configuration file of proftpd, I place the following setting section in the <anonymous> section,
Code:
After restarting the proftpd server and applying the configuration, I try downloading a file in IE browser. Sometimes, it prompts a saveas dialog, and everything was okay.
However, it occasionally prompts a login form instead of a SaveAs dialog. This makes our customers confused greatly.
So, how could I prevent browser from prompting login form when anonymous users try to download files from our ftp server?
Quote:
OS: CentOS 5.3
Server: ProFTPd 1.3.1
I've recently installed Proftpd to host for someone for a couple of hours.
With the default config it works however when taken the comments out and edited for anonymous, proftpd fails to start
This is the default config file which works if you have a user and password for my machine, but anonymous wont work (when the comments were removed).
Is it possible for vsftpd to have logs so I can see IP addresses user has used to connect to FTP ?
View 3 Replies View RelatedI am trying to install VSFTPD on my Fedora instance of Linux. I have a Wordpress blog that I want to access through FTP. I did an install on VSFTPD and am kind of stuck. I try to FTP into my IP through [URL]
View 2 Replies View Relatedi have a server and im trying to use ftp to edit my website with dreamweaver. im using vsftpd and i have access where i can read all the files but i cant add any. any clues?
View 5 Replies View Related
