Red Hat :: No Static IP Possible With WLAN Adapter Broadcom
Feb 2, 2010
I have freshly installed RHEL 5.4 on a Dell Inspiron with WLAN adapter Broadcom 4318. The original driver bcm43xx did not work. So I installed ndiswrapper for using the windows driver.Now I can connect via DHCP, but when I try to assign a static IP address, it still uses the IP address provided by the router (AVM Fritzbox 7270). I always did ifdown/ifup and the static IP and everything else is present in /etc/sysconfig/network-scripts/ifcfg-eth1. But ifconfig always shows the IP address assigned by the router. When I switch off the DHCP server of the router I can't connect to the network anymore. The LAN adapter Broadcom 4400 is working well with a static IP address.
View 3 Replies
ADVERTISEMENT
Jun 15, 2010
I have set at static ip on eth0:
In have configured the /etc/network/interfaces as:
Code:
auto lo
iface lo inet loopback
auto eth0
[Code]....
However, I experience a slow Internet connection when using wlan.
Is this a routing issue, or have I configured the /etc/network/interfaces config file wrong?
I use Ubuntu 10.04, 2.6.32-22-generic
View 2 Replies
View Related
Oct 7, 2010
I'm trying to use the nm-applet tool get a static ip on my wlan. I've created a configuration and set up the IPV4 settings ok but I can't figure out how to stop nm-applet from creating and using the auto wlan configuration. I've tried deleting the auto config but it seems to recreate it when I try to use wireless again. How to make the manual config the default or permanently disable the auto (dhcp) config?
View 2 Replies
View Related
Nov 20, 2010
I'm having trouble setting up new Alix URL... system with a wireless card. I got the card from an old working Buffalo AirStation router. The card is a WLI-MPCI-G54 and is using Broadcom BCM4306 chip. I've installed Debian on the system.My goal is to make a wireless access point by using hostapd authentication service. I thought it might be a good idea to verify that the wlan-card is working properly first, but it can't seem to detect my local wlan.
View 1 Replies
View Related
Feb 9, 2009
I have an HP Pavilion notebook with a Broadcom WLANcard that had been working very nicely in Fedora Core 10 until this evening, when I took my notebook to a conference room where there was no internet access. (I tried to connect to wireless networks, but there were none in the area, as I discovered.) am now unable to connect to my local (home) wireless network as the device is now non-existent . Can someone please walk me through the steps to fix this or re-install it (I have tried reinstalling broadcom-wl, but that didn't help). My lspci listing is reproduced below:
Code:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
[code]...
View 10 Replies
View Related
Aug 16, 2010
I'm trying to install the drivers for my Wlan card, I've downloaded the drivers in the tar.gz-file from Broadcom and untar-ed it in my /home/<username>/hybrid_wl-folder and cd'ed to it and I try to run "make" but I get an error: KBUILD_NOPEDANTIC=1 make -C /lib/modules/'uname -r' /build M='pwd' make: *** /lib/modules*2.6.31.5-0.1-default/build: No such file or directory. Stop make: *** [all] Error 2
I'm getting really desperate, I need my Wlan on Wednesday. I'm following the README but this is what I get.
View 7 Replies
View Related
Mar 13, 2010
I'm finding a hard time getting my wireless card to work, my laptop is a Dell Inspiron 1525 and this is all the info:
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
0b:00.0 0280: 14e4:4315 (rev 01)
[ 8.375610] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[ 8.390374] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 6, Type 5, Revision 1)
[ 8.390436] b43: probe of ssb0:0 failed with error -95
View 9 Replies
View Related
Sep 22, 2010
My laptop is the one mentioned in the title. And it's completely offline at the moment.
Code:
$iwconfig
lo no wireless extensions.
Seem to have some troublesome chips.
Code:
$ lspci
03:00.0 Ethernet controller: Atheros Communications AR8151 v1.0 Gigabit Ethernet (rev c0)
05:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01)
code....
although in my case they should be for the 2.6.33.3-85.fc13.x86_64 kernel.
And I've been searching that repo for ages now, and I can't seem to find anything with kmod-wl or broadcom in there. I'm well aware that this is most likely because of my own ignorance as to the build up of said repo.
View 2 Replies
View Related
Aug 2, 2010
I have Ubuntu 10.04 installed and can browse the internet via cable, but wireless isnt working. My wireless driver is "Broadcom 802.11b/g WLAN".
In the windows device manager, I found the corresponding inf file to be oem20.inf which I tried to install it through "Setup Windows Driver" but it gave an error saying invalid driver. I also tried installing the Broadcom STA driver, but that didnot help.
I am dual booting with Windows 7, and i installed ubuntu through the windows wubi installer. My laptop is HP Pavilion dv4. I have installed the regular Ubuntu desktop and have made all upgrades. The results from lspci command i have added below.
gowda@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
[Code].....
View 2 Replies
View Related
Jun 18, 2011
I have Lenovo Notebook 3000 N100 with built in wireless - Broadcom BCM4311 802.11b/g. The seems to be properly installed(as per the screen shots) but still I can not see any wireless networks. I checked out most of the forum but could not find any exactly matching situation. find the attached results of the below command which might give you idea : sudo lshw -C network
As per one of the screen shot it seems that "This drive is activated and currently in use" still I can not see any routers(including mine) which I can connect. Also the Wifi LED is not glowing.
View 1 Replies
View Related
Jan 12, 2010
I have just installed Ubuntu 9.10 on an Acer TravelMate 290E. I've got internet connection through the Ehternet Cable, but when I plug in the D-Link WLAN USB device, although the system recognises it, it is disconnected. How can I connect the WLAN USB device adn get it to work?
View 5 Replies
View Related
Mar 11, 2011
just swapping all my computers over to linux as it far far better than anything i've used before. Have the above driver as identified in lsusb.[URL].. Downloaded the linux driver but dont know what to do from here. Tried doing it the windows inf file way but that didnt work. Or more like i couldnt get it working.
View 9 Replies
View Related
Nov 24, 2010
I have found instructions but they are not working. I am new to Ubuntu and have only had a few classes that dealt with Fedora and CentOS. So I am rather new to Linux in general. The drivers say they are compatible with linux kernel 2.6 and later so I am going to assume they should work with ubuntu--am I correct in this assumption? If so, when one installs anything in ubuntu should one be set as the admin?
View 4 Replies
View Related
Oct 12, 2010
my OS is linux ubuntu x64 v10.10 on netbook dell vostro 1520. i'm looking for wlan [COLOR=#00C800 ! important][COLOR=#00C800 ! important]drivers[/COLOR][/COLOR] for network adapter broadcom like this:
Quote: Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01)
View 9 Replies
View Related
May 28, 2011
I patched my wireless driver in order to support packet injection. Using this tutorial:
- Install the Firmware:
Code:
- Create new directory:
Code:
- Now disconnect Internet and unload all your driver (use rmmod command)
- Move/copy the Compat-Wireless patched in /usr/src/drivers directory and unpack the drivers:
Code:
Blacklist the wl driver: (STA driver)
Code:
Currently I'm running Ubuntu 10.10, Kernel 2.5.35-29-generic. I have a Broadcom 4318 for my WLAN and a Broadcom 4401-B0 for my ethernet. I followed the tutorial and I managed to get packet injection working on my WLAN; however, my ethernet connection isn't working. I tried sudo modeprobe b44, but I get the following message:
FATAL: Error inserting b44 (/lib/modules/2.6.35-29-generic/kernel/drivers/net/b44.ko): Invalid argument
View 9 Replies
View Related
May 2, 2011
I've got Fedora 14 (2.6.35.12-90.fc14.i686.PAE) installed and i'm trying to use hostapd with my Realtek RTL8191S USB WLAN Adapter, but can't get it to work. The driver i'm using is : rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 601.tar.gz
[Code]....
View 2 Replies
View Related
Jun 6, 2010
I dual boot windows xp and ubuntu 10.04 LTS and the wireless card works perfectly fine in xp so I know its not a hardware/network issue. In ubuntu, it detects wireless networks, will connect to network and work for about 20 seconds.
[Code]....
and it continues on after this alternating between a normal 20ms and high ping over 200ms. The connection refuses to load anything off the internet/local network.
View 5 Replies
View Related
Jan 19, 2011
I updated Ubuntu to 10.04 after which I noticed the wireless indicator lights on my HP laptop were continually flashing between blue and orange and network performance seemed slow. I did some searching and found and implemented the following change to stop the flashing:
gksudo gedit /etc/modprobe.d/wlan.conf
Copy and paste the below line:
options iwlcore led_mode=1
Since making this change the wireless connection is shut off and I can;t get it to work at all. I first tried simply to remove the change to get back wher I was, but I can;t do that. Can sopmebopdy toell me at least how to get rid of this wlan,conf file ( it was created by the above command) so I can start over?
Coincidentally since making this change my Windows Vista OS fails to start because of errors attributed to a software or hardware change, of which there were none other than the Ubuntu wlan.conf change. . It may be unrelated but I am suspicious of the coincidence. I am running Vista and Ubuntu in a dual boot configuration and all ha run very well until I did the Ubuntu wlan.conf change.
I am now attempting a complete recovery of my Vista system, since it seems irreparably broken. Again coincidence or not?
View 2 Replies
View Related
Jun 22, 2011
(For the record, I have already read the other threads. Either they don't work for me or are too difficult.) My laptop is an Acer TravelMate 250. I have installed Ubuntu 10.10 (2.6.35-28 generic i686) after erasing Windows 7. At first, the usb wireless adapter worked. Then, I restarted the PC because of some updates and it didn't work anymore. In "edit connections" I find "Auto SpeedTouch8350DB" which is the wireless connection (on my sis's computer it works). When it tries to connect, I'm asked the password but it doesn't work.
[Code]...
View 3 Replies
View Related
Dec 14, 2009
I'm having some issues with openSUSE 11.2 recognizing my Broadcom adapter. Following the instructions in the two stickied topics, I can find the adapter both under YaST's Hardware Summary and using the console command /sbin/lspci. I cannot, however, find it with /sbin/lspci -n, and the boot log (viewed with dmesg | less) makes no mention of it either.
Do I need to turn it on or something? This is a dual boot machine, and it works fine under Windows, so I don't think there's a hardware failure at play here.
View 9 Replies
View Related
Jan 3, 2010
Basically a few weeks ago I decided to try Linux, in particular Ubuntu. I have it installed in my Windows 7 partition but now I am willing to take the full plunge and switch to it all the way. The only issue is I cannot connect to wireless internet. It states "device not ready". Wireless is turned on on my laptop, I am very near the source, have tried making a manual connection with the network setup. I tried the hardware tester and it found my ethernet and wireless hardware (Broadcom 802.11g Network Adapter).
I went to the package thing and looked for Broadcam. I found a package but it was already installed. I tried it manually with:
sudo apt-get install bcmwl-modaliases
E: Could not get lock /var/lib/dpkg/lock - open (11: Resource temporarily unavailable)
E: Unable to lock the administration directory (/var/lib/dpkg/), is another process using it?
I then heard to try "sudo apt-get install bcm43xx-fwcutter" and did but it couldnt find it.As stated before I am new to linux so I'm probably missing something easy I just beg your patiance as I learn this new operating system.
View 4 Replies
View Related
Jun 19, 2011
i have a broadcom BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) wireless adapter on a dell 1501 run by ubuntu 10.10.this particular model and revision is suppose to be absolutely supported by linux and indeed it did work perfectly before the user ran a upgrade from ubuntu 10.10 to 11.04.subsequently i have reinstalled 10.10. as i recall when i installed ubuntu 10.10 the first time i simply ran the System>Admin>Additional Driver installation tool to make the wireless work. i cannot recall if i ran the b43 or the sta driver but i have tried both this time and had no luck.
i am aware that the broadcom adapters are notoriously troublesome and i have tried the two workarounds here URL... as well as their third alternate workaround with no success.
View 3 Replies
View Related
Feb 8, 2009
A friend of mine has a Dell XPS1530 lappy that has a broadcom bcm4328 wireless adapter. I tried installing kismet on it so I can scan for wireless network in range. I configured it with the source driver as bcm43xx in kismet.conf and complained that the driver didn't support monitor mode. It uses the proprietary 'wl' kernel module to operate but kismet can't use the 'wl' module and it says the same error. I tried unloding the wl and b44 modules and loding the b43 driver but then the adapter stoped working. I searched on the net a bit and found out that kisment doesn't work with the prorpietary drivers for that card.
View 14 Replies
View Related
Aug 26, 2009
Okay I posted about this a while ago, and i got my wired network to work, but now i need my wireless card driver to work. I have been doing research and I found something called ndiswrapper which drivers from windows working in linux. I typed in lspci in the terminal and it gave me my specs of my wireless card which is a:
-Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03)
-Some people said there is no original driver for this card, so you need to use ndiswrapper, I was wondering does anybody know what this is, how do i use this, and help me out to get my wireless card going. If you give me instructions, please be really specific as I am really new and still getting the hang of commands.
View 1 Replies
View Related
Jan 13, 2010
I was running 9.10 in LiveCD mode and was unable to get online. Went to System>Administration>Hardware Drives and found "Broadcom STA wireless driver". Cool. So I went ahead and installed 9.10 (dual boot with Vista), repeated above steps but found no "Broadcom STA wireless driver" option, in fact no proprietary drivers. So I still cannot connect to the Internet, and I don't know where to go from here. (Note: I installed 9.10 side by side with Vista: good? bad?)
[Code]...
View 9 Replies
View Related
Nov 27, 2009
There is no wlan0 interface when trying to run FRITZ!WLAN USB Stick N 2.4 on OpenSuSE 11.2, though it works fine on Fedora 11 and Mandriva Spring 2009.1. All 64bit. Contrary to Fedora and Mandriva, there is no need to compile the compat-wireless module ar9170usb for OpenSuSE 11.2 because the kernel is very recent and includes this driver. Kernel: 2.6.31.5-0.1-desktop The /var/log/messages gives this after I put the stick in the PC. At first it is seen as a mass storage device:
Nov 27 22:00:24 linux-3mwa kernel: [ 73.420755] usb 1-5.1: new high speed USB device using ehci_hcd and address 4
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540834] usb 1-5.1: New USB device found, idVendor=057c, idProduct=84ff
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540841] usb 1-5.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540847] usb 1-5.1: Product: FRITZ!WLAN USB Stick N 2.4
[Code]....
View 5 Replies
View Related
Feb 12, 2010
I'm having some problems on the line with ***. This is from a OpenEntidade.java class file and I'm trying to update EmprestadorView's variables.
EmprestadorView.java
public class EmprestadorView extends FrameView {
...
OpenEntidade.java
-----------------
public class OpenEntidade extends javax.swing.JFrame {
[code]....
View 2 Replies
View Related
Apr 26, 2010
I got this message on Friday from just one domain. uote:mailsrv.forthnet.gr #<mailsrv.forthnet.gr #5.5.0 smtp; 554 5.5.0 Your message was considered to be spam by the FORTHnet Antispamming Policy and was not delivered to the recipient. The following spam tests returned positive for this message:FORGED_RCVD_HELO,RCVD_IN_BRBL. For further information visitWe are not a spamming community but it seems we have a statice IP address that has a Reverse lookup to "myipaddress.static.lyse.net" and not my email domain. Would setting a cname mail.mydomain.no -> myipaddress.static.lyse.net cure this problem or are there more tricks to be performedOnce I have cured the FORGED_RCVD_HELO I can move to getting the IP removed from BARACUDA.
View 2 Replies
View Related
Mar 31, 2010
To create a static library, or to add additional objectiles to an existing static library, I can use a command like this:ar rcs my_library.a file1.o file2.oBut how to add an existing static library to my own static library. I have created my own static library using the command above and want to link against the library libuuid.a (placed in /usr/lib/).
View 6 Replies
View Related
May 28, 2010
I have this output from lspci
Code:
04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)
07:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express (rev 02)
when i try configure using network manager, i can not connect to wlan, my AP using WPA-PSK
View 7 Replies
View Related
