I have this output from lspci
Code:
04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)
07:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express (rev 02)
when i try configure using network manager, i can not connect to wlan, my AP using WPA-PSK
I installed Fedara 15 yesterday. I was running Fedora 13 before. Since I did the fresh install, my wireless network runs really really slow, i.e. a few KBs every 30 seconds whereas it ran at full speed in F13. I couldn't find the reason for it. I now tried the live-CD for Fedora 14 and it runs at full speed out of the box (whereas F15 is slow even with all updates installed).
Does somebody know a solution?
Laptop: Lenovo X201
Network Card: Ultimate-N 6300
I gathered uname, iwconfig, lspci and dmesg output for both, Fedara 15 and Fedora 14. But as the number of links is limited here in the forum they're all linked here: [URL]
I am newbie to linux, I am dealing with Fedora core 13. I have already succeedded in building an ad hoc network and a WLAN network. My next step is to get some networking statistics such delay, throughput, etc. So, I need traffic to flow through the network for both multimedia traffic and bulk data traffic. How to send files between nodes on the network (I found commands ftp, rcp but do not know whether they are the correct choice for this). ID their any application to perform this?
Also, I want to perform some video streaming between two nodes to study the behavior of real time data transfer. Is thier any application to perform this?
I couldnt find something for changing mac address for wireless. how to do that....
View 4 Replies View RelatedI have been using FC10, it works well with wlan for sometime and goes inactive after some time and hence network goes unavailable. Even after few attempts to reconnect doesn't help. Rebooting helps in bringing it back temporarily.
View 7 Replies View RelatedI recently got a laptop computer and installed 64 bit fedora 11. I can make wireless connections fine but for my ISP I require a dial in using an username and password. On my desktop this is easy I just make a DSL connection under network manager and select eth0 my wired network card as the hardware and away I go. But now I can't select the wireless card as my hardware connection so my DSL keeps on trying to connect through eth0 which is obviously not plugged in. How do I go about making this connection? I have searched google and other people have this problem but I haven't seen any replies. I have tried using pppoe-setup and manually setting the hardware as wlan0 but this doesn't seem to work as under network manager it just defaults back to eth0.
View 7 Replies View RelatedI installed Fedora 14 yesterday via the installation DVD with 3,3 GB. Everything worked fine and when I connected to my wlan and entered the WEP key I got access to the internet. But after about 5 minutes, to connection just got cut and I was again asked for the WEP passkey. But when I entered it this time, the connection failed and I was just asked again (with the same key entered, it even got it saved from last time). As you can think, this is quite annoying, since the time I have internet is not even enough to get some updates done.
Ah, and by the way: The time I have internet it just is unbelievably slow. On my Windows partation, I don't have this problem. I do have a small hint what might be the problem: When I was using Ubuntu, I always had a similar problem, but it did not even connect to my wlan once. The solution was to blacklist some driver, but since I don't know if this might be the problem on Fedora too and if the drivers are the same as on Ubuntu and since I really have no idea about the syntax of the terminal here, I was not daring to try this out.
How do I install my driver wlan in Fedora 14? I use this notebook hp:
http://h10025.www1.hp.com/ewfrf/wc/p...reg_R1002_USEN
I have already installed the update of fedora and still does not work.
Installed F14 on my daughters HP Pavilion a131On. I rebooted multiple times. Do I need to activate something? I'm new to all of this but read through many threads to do as much as I could myself. I used the GUI to load the rt3070 drivers rather than rpm. The GUI is easier I think and should be equivalent. Please let me know what else I need to do. Fedora has been great on my Lenovo but this usb wlan stuff has been a pain.
[Code]...
I am unable to connect to the internet in fedora (XP connects fine) I normally use wifi, but have also checked the wired connection.
View 10 Replies View RelatedI'm running Fedora 15 KDE on a Sony Vaio VPCS13V9E. No problems in connecting to the wlan. Today I upgraded the system. There was an upgrade for Network Manager. After the upgrade the system is not able to connect to the modem - router (Linksys WAG320N) any more. Network manager keeps on crashing and sends messages like "network disabled" or "connection failed". Kde demon is reporting errors too. I guess the new version of Network Manager is bugged, because before the upgrade it did work well ... (unbelievable!).
lspci: 02:00.0 Network controller: Intel Corporation Centrino Advanced-N 6200 (rev 35).
Subsystem: Intel Corporation Centrino Advanced-N 6200 2x2 AGN
Flags: bus master, fast devsel, latency 0, IRQ 44
Memory at dd100000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlagn
Kernel modules: iwlagn
I installed F10 today. From live-usb wlan worked fine, but after installing it doesn't find any networks. I tried to google this problem, but everybody says wifi works out of the box. Not for me.
Solved: I disappled wireless networking and appled it again. It found all networks.
I have a Dell XPS M1330. I installed Fedora 10 on a separate partition and left Vista on the first. It was working just fine and for some reason all of the sudden it is not recognizing the Wireless controller. Vista is still working fine although I did get a couple of "WLAN controller has stopped working" errors. I suspect I may have a physical problem with the controller but I'm confused as to why Vista is still using it but Linux is not. The actual physicall "WIFI" light on the laptop does not even illuminate when I boot Linux. No wireless networks appear in the network list under Linux. Particularly since it WAS working fine for months...
View 4 Replies View RelatedI have a problem with my Intel PRO/Wireless LAN 3945ABG, The laptop doesn't have a hardware "turn-on" button for Wireless device, normal "windows shortcut" aren't also working. I couldn't turn it on using Network Configuration, it keeps giving me this message:
Error for wireless request "Set Mode" (8B06) : SET failed on device wlan1 ; Invalid argument. RTNETLINK answers: No such device Determining IP information for wlan1... failed.
I have installed Fedora 12 on my laptop.Installing my Broadcom BCM 4312 wireless drivers works just fine, but after a reboot I have to reinstall them. modprobe wl, modprobe wlan0 etc doesn't work either. I need to reinstall them every time I reboot.
View 7 Replies View RelatedSince I have installed Fedora 13 it seems that I can't connect to WLAN APs which aren't secured by WPA. I'm surprised about the inserts to the messages logfile:
[Code]...
Most surprising insert for me: Jul 5 20:43:21 nbtobiaslnx NetworkManager[1328]: <info> Config: added 'key_mgmt' value 'WPA-PSK' Is this the reason for my problem? I use KDE and Network Manager for managing my networkconnections.
I have an HP Pavilion notebook with a Broadcom WLANcard that had been working very nicely in Fedora Core 10 until this evening, when I took my notebook to a conference room where there was no internet access. (I tried to connect to wireless networks, but there were none in the area, as I discovered.) am now unable to connect to my local (home) wireless network as the device is now non-existent . Can someone please walk me through the steps to fix this or re-install it (I have tried reinstalling broadcom-wl, but that didn't help). My lspci listing is reproduced below:
Code:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
[code]...
Recently, I had the courage of installing Fedora 11 on my laptop while risking of trashing my Windows XP. Fortunately, the installation went fine and windows and fedora seems to be working together. But I needed to reinstall Fedora because I didn't do the partitioning right. After that the problem arises. I couldn't connect to the wlan. The first installation it was working fine. Now I can't. I select the network, enter the password and then it just says "Disconnected" or something like that then nothing else happens. So I had to reinstall it again thinking I did something wrong on the installation. But still it wasn't working. But it seems to be working when I boot from the live cd. I must have messed up my network configuration.
View 7 Replies View Relatedi use fedora11 and try to use wireless i find driver for chip Realtek RTL8187 but want to know command to install it. i save folder of driver on desktop in folder name rtl8187_linux_26.1010.0622.2006has like this
[Code]....
I've been using Fedora 13 for a few months now on my desktop and since ethernet is not a choice I needed to use a wlan adapter. I did a little research and ended up using a Linksys WUSB54G ver. 4 which worked great (plug and play, no ndiswrapper or any other configuration required) on my wireless g network, using WEP protection. About a week ago I started looking for methods of upgrading my system because. well I just like being somewhat current.
Anyway I used a Fedora 14 Install DVD and used the upgrade option and it worked. All my settings (seem) to be exactly the same as my Fedora 13 settings were and the appearance and location of files etc. are all the same. Now, for some odd reason, to me at least, Fedora isn't showing a wlan icon in the upper right hand (by the way I'm using GNOME) corner like it used to and doesn't seem to have configured my wlan device correctly. I ran lsusb and it shows the device ID (13b1:000d) and the name (Linksys WUSB54G v4 802.11g Adapter [Ralink RT2500USB]) I'd just like to get my adapter working again like it did in 13. I have kernel version 2.6.35.6-45.fc14.i686.
I've got Fedora 14 (2.6.35.12-90.fc14.i686.PAE) installed and i'm trying to use hostapd with my Realtek RTL8191S USB WLAN Adapter, but can't get it to work. The driver i'm using is : rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 601.tar.gz
[Code]....
I have just updated KDENetwork to this level and now my F10 doesn't find any wifi connection. By the way, I have been working with F10 for some months without any problem on wlan.
iwconfig now says:
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
[code]...
I have a Dell Latitude D800 with a Dell Wireless 1350 (802.11b/g) WLAN miniPCI Card. I need to install wireless on this laptop but I see no wireless card when I know I have the above wireless card. Here are some commands that I ran that I might prove useful:
[Code]....
There is no wlan0 interface when trying to run FRITZ!WLAN USB Stick N 2.4 on OpenSuSE 11.2, though it works fine on Fedora 11 and Mandriva Spring 2009.1. All 64bit. Contrary to Fedora and Mandriva, there is no need to compile the compat-wireless module ar9170usb for OpenSuSE 11.2 because the kernel is very recent and includes this driver. Kernel: 2.6.31.5-0.1-desktop The /var/log/messages gives this after I put the stick in the PC. At first it is seen as a mass storage device:
Nov 27 22:00:24 linux-3mwa kernel: [ 73.420755] usb 1-5.1: new high speed USB device using ehci_hcd and address 4
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540834] usb 1-5.1: New USB device found, idVendor=057c, idProduct=84ff
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540841] usb 1-5.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
Nov 27 22:00:24 linux-3mwa kernel: [ 73.540847] usb 1-5.1: Product: FRITZ!WLAN USB Stick N 2.4
[Code]....
At my workplace the wireless connection is open but once you connect you first need to authenticate on your browser to be able to use the internet.On Windows as soon as I open whatever page I get the login request.On Linux I open firefox but nothing happens, just get the usual error page like if I had no connection. The IP's I get as well as DNS seem ok, I even tryed to match them up with windows.I tried a lot but can't get to the login page.
View 3 Replies View Relatedspecific Ubuntu supported WLAN PCI-cards? This link shows a list of supported PCI-cards, but which is best: [URL] And the installation needs to be easy! I�ve tried installing these PCI-cards in my computer, useing Linux drivers, NdisWrapper, etc. Unforutately without any success:
- DWL-G510, Ralink Chipset, Ralink RT2561/RT61
- Realtek Semiconductor, RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller
Today I upgraded from 10.10 to 11.04. After accidentally turning off the computer during the upgrade, booting into recovery mode, remounting the file system as writable and finishing the upgrade, it worked just fine.
However, I can no longer use any wireless networks. Wired ethernet works fine, but the wireless inteface won't even show up when I run ifconfig. When I first installed 10.10, it worked instantly and I was able to use it during installation.
I have an HP Compaq nx7300 laptop with a Broadcom BCM4311 network card.
I installed 11.04 to ASUS Z9200 Notebook, at first all was fine at least 10 minutes, LAN, WLAN worked ok, but suddenly all is gone, restarted few times -nothing. reintall-nothing...here is some info....any ideas?
mm@mm:~$ sudo lshw -c network
[sudo] password for mm:
*-network:0 DISABLED
description: Ethernet interface
product: 88E8001 Gigabit Ethernet Controller
vendor: Marvell Technology Group Ltd.
physical id: 0
[Code]...
I have hp dv6291 laptop with Centos 5.2 os the NIC & WLAN not working ?
View 2 Replies View RelatedI have a Thinkpad T400 notebook that dual boots windows 7 and Ubuntu 9.04. My wireless has worked both in windows and ubuntu for the past several months. However 2 days ago, the wireless in ubuntu stopped working. I think this may be a result of trying to set up a static eth0 connection between my laptop and an embedded board, but I dont see how messing with eth0 would stop the wlan from working.
Symptoms: When I left click on the network connections icon in the tray, all it lists under "Wireless networks" is "device not ready". Needless to say, there are no networks available to connect to. Also the wireless is working fine under windows.
[Code]...