OpenSUSE Wireless :: Realtek RTL8187B Connects To Network But No Internet?
Jan 7, 2010
Got a laptop with a RTL8187B wlan card, installed opensuse 11.2 on a 50gb partition. Card was detected straight away but only connects when I enter ip addresses manually, DHCP don't work.
When it is connected it always stays at a speed of 1mb/s and it cannot ping my router or anything else.
Me kernel is 2.6.31.8-0.1-desktop
Searched around the forums but no love, tried compat-wireless but it started crying about dependencies. Modprobed it too..
View 8 Replies
ADVERTISEMENT
Mar 9, 2010
In openSuse I can connect to a wireless network. It says that it is connected, and I can open the router page (http://192.168.1.1/basic.html). But I cannot load any other pages. Nothing else recognizes internet either; I tried using konqueror, YAST and wget with the command line, and none of them could load anything. It is not a router problem or a wireless card problem because both Ubuntu and Kubuntu can connect, from the same computer. I know this is odd because in the only other thread I could find with this issue, it was a different distro and installing openSuse seemed to fix it.
Hardware:
Computer: Yakumo Notebook model 331
Network Card: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
RaLink RT2500 802.11g Cardbus/mini-PCI (rev 01)
View 5 Replies
View Related
Jan 7, 2010
I can connect to the internet fine, but it refuses to go any quicker than 1mbit. Below is my recent result from [URL]
My iwconfig shows...
Code:
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
[code]....
View 1 Replies
View Related
Mar 10, 2011
I'm using the new opensuse 11.4 with KDE desktop. I can connect to my WPA2 personal network fine, but some other networks, like a WPA2 enterprise network connects, but no Internet(pinging too) resolves.
View 2 Replies
View Related
Jan 9, 2011
I have an Acer Aspire One D255 netbook with opensuse 11.3 installed and after several painstaking days of tinkering I successfully installed the broadcom wl drivers, and now my wifi card is operational. However, i can connect to my wireless network, but still have no internet access. I have searched the forums and google for a solution but most issues I have found that are similar to mine have been resolved once the wl drivers and firmware where installed
View 2 Replies
View Related
Mar 24, 2011
I just installed SUSE 11.4. In short - my adapter is working, authenticated on the selected AP, I can ping the AP, but I have no access to the outside world. Here's the command line output:
xaoc@FOREST:~> dmesg ...
[795.517345] wlan0: authenticate with 00:01:38:e2:39:8c (try 1)
[795.533595] wlan0: authenticated
[795.638329] wlan0: associate with 00:01:38:e2:39:8c (try 1)
[795.640960] wlan0: RX AssocResp from 00:01:38:e2:39:8c (capab=0x431 status=0 aid=3)
[795.640964] wlan0: associated .....
--- 192.168.1.1 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4004ms
rtt min/avg/max/mdev = 2.118/5.169/16.063/5.454 ms
xaoc@FOREST:~> ping -c 5 66.70.73.150
connect: Network is unreachable
View 7 Replies
View Related
Apr 26, 2011
trying to get my little Encore USB wireless adapter to work on several flavors of Linux (Ubuntu 10,10, ElementOS, Xubuntu, and Puppy), I emailed tech support at Realtek. I asked where is the Linux driver for this product? I did this because there were no Linux drivers posted on their site and everyone here (and on Newegg) is jumping though hoops trying to get a working wireless connection with the Encore and similar dongles that use the RT8187b chipset. I didn't expect an answer, but felt better after my little vent. I get an email from Realtek with a driver. Realtek needs to promote Jerry -- a beacon of customer service in the age of the "get lost" school of customer relations. I have attached the driver below. Caveat: I have not yet compiled the driver, so I don't know much more about it than I've said already, although the archive appears to contain the source code.
View 3 Replies
View Related
Aug 27, 2010
I am having trouble getting a Realtek RTL8101E/RTL8102E PCI Express Fast Ethernet controller to work on openSuSE 11.3. Most of the data for the problem is in this pastebin of the output of Framp's collectNWData.sh. I have also downloaded drivers for this card as detailed below.
Code:
stephen@linux-75on:~> zypper se -r drivers:nic -i
Loading repository data...
Reading installed packages...
Also, here is the more complete output of /usr/sbin/iwlist scan:
Code:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
pan0 Interface doesn't support scanning.
View 9 Replies
View Related
Jul 2, 2010
During the installation of Opensuse 11.2, I tried the wireless internet connection, and it kept coming back failed.I continued to install the system and when I got on, I entered the SSID (think that's the right way to say it), and the password.When showing that 'map' or whatever, it showed the SSID in the networkmanager.It also said "active".But when clicking on Mozilla Firefox, nothing happened. It just said the server is down.I'm on another Linux system now; so I know the wireless works. It worked great on a third one as well.It is some Atheros Communications, AR5001.I'm not sure what other information you need. Just let me know and I will do what I can to provide. I don't have opensuse up at the moment. I screwed up the dual boot. so right now it's been erased. I'll ask for help on that in another topic.
View 9 Replies
View Related
Jun 20, 2010
I recently installed Xubuntu 10.04 on my desktop computer that had a USB wireless adapter DLink DWA-140. I didn't have to install any additional drivers to get it to work. I put in the network SSID and the password and was connected immediately. However, when I try starting firefox it doesn't load any sites. Can anyone help me in approaching this problem. I have a DLink DIR-655 router. If I should gather more information to get this problem solved then please let me know and I will do so.
Edit: Now I am unable to connect to the network. When I click the network icon in the taskbar, my home network is not visible while it is visible under another ubuntu computer I'm running.
View 2 Replies
View Related
Aug 25, 2010
I installed Ubuntu 10.04 32-bit on an old desktop (1.5ghz Pentium 4, 20GB hard drive, 768MB RAM) a week or two ago, at the same time that I installed Xubuntu 10.04 on an even lower performance IBM tower server. The server functions perfectly and my other (Windows XP) desktop recognized it from the start, as did the Ubuntu desktop. However, I rearranged a few ethernet cables the other day without turning off the desktops and ever since my Ubuntu machine does not recognize my server, even though all of the devices are connected via ethernet cable to a linksys router and it connects to the internet without a problem. I'm a linux newbie - this is my first move away from Windows - and I don't know where to turn. Far more confusing is the fact that, when I boot from a LiveCD, the network is recognized and I can read/manipulate files on my server without a problem. Oh, and I briefly flirted with OpenSUSE KDE (not as noob-friendly as Ubuntu, so I'm back) and encountered the same problem.
Needless to say, booting from the hard drive is preferable to booting from CD every time
View 3 Replies
View Related
Apr 23, 2010
The computer connects wirelessly to a router. The router is connected to the internet and that is working well. (If i use a cable connection to the router, I can reach the internet).
Why wont the wireless connection reach the Internet? It is a strong connection. It worked before wirelessly. I am on 10.04 beta, with the recent updates installed.
View 1 Replies
View Related
Jan 16, 2011
My wireless adapter connects to my WPA2 network perfectly, but when I run firefox it says it can't load the webpage, no matter what page I go to. Also, downloading new software doesn't work either. Any ideas please?
View 9 Replies
View Related
Jan 9, 2010
I've got a Zotac MAG HD-ND01 with XBMC live installed. This is built on Karmic Koala and runs very nicely through the wired NIC.
I configure the box using a cable. I'm using WPA2-PSK and it is clearly authenticating OK.. It gets an IP address.. the AP shows a connection to the box. My XP laptop connects to the access point OK.. just can't connect to the box via the wireless, and it can't see the network using wireless.
I have followed a number of threads on connecting Atheros 9XXX wireless [URL] but no joy.
Also, can Ubuntu connect to the AP at any speed greater than 54MB? My windows PC connects at 144MB+ . Will ndiswrappers connect at those sorts of speeds?
lspci -nn
04:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
iwconfig
lo no wireless extensions.
[Code]....
View 1 Replies
View Related
Aug 9, 2010
I have one pc on which I have installed slackware and samba (fixed IP, mask 255.255.255.0) I have another PC (also XP) which also has fixed IP running XP, and I can connect that to the slackware server easily My third PC connects to the internet and gets its IP address from the Cisco router(?) that provides the IP and mask on boot up.
I tried changing the IP and Mask on the slackware server to match the internet PC (which uses a mask 255.255.254.0) but the PC mask and IP changed on the internet PC I want the PC that connects to the internet to also be able to connect to the slackware server, but I see no need for the slackware server to also connect to the internet - I will mainly use it as a file server When I worked for another company I think the IT department talked about having 2 network cards in the PC that connects to the internet
View 6 Replies
View Related
Aug 6, 2010
I know Windows forward and backward but I am so new to linux it's just wrong. I just installed fedora (like 1hr ago) on and old toshiba laptop with a WiFi PC card. Everything seems to work fine except. My Networks connects to my home Wifi network but it will not connect to internet. When it connects the IP address isn't even close to being in the same range as my other laptops and PCs. Like I said I'm new to linux but I'm wanting to learn. Any fixes for this issue? Which linus book is the best one to read for a beginner? Other then not connecting to internet I have no complaints.
View 14 Replies
View Related
Aug 5, 2010
I am getting trouble with knetwork manager. I created a new connection by scanning and connecting using knetwork manager. But every time connection gets disconnected and ask for password and again it connects.
View 8 Replies
View Related
Dec 3, 2009
I have a Toshiba Satellite L305-SP6944C, Pentium Dual Core 2.16, 2GB RAM, 160GB hard drive, DVD-RAM UJ880AS, display 15.6 TFT widescreen, ethernet Realtek RTL8101E/RTL8102E PCI Express, WLAN Realtek RLT8187, Opensuse 11.2 and KDE 4.3.1. Installation was OK and finally the wireless card is working... but I don't have conectivity bacause in the browser (Firefox) appears a message saying "the server can't be found"
I follow the howto write by Swerdna. With ndiswrapper I install the XP driver for RLT8187, KnetworkManager is in charge of connections showing both eth0 and wlan0, the wireless sign of router Dlink DIR-280 is OK, in the dialog box of network connection I put the mac address of the wlan card but I think that is not the problem.
Other thing that I missed is that I don't find boot.ini at any directory to add modprobe ndiswrapper in the boot sequence, in etc/init.d/ appears a "boot" file, is this file that I have to change to modprobe ndiswrapper??
View 9 Replies
View Related
Jul 12, 2010
my wireless home network is not recognized by my network card (RealTek RTL8190 mini PCI). The post was as follows: "I am using a new computer with Windows 7 , Athlon quad core 2.60 64 bit, 8GB RAM. Internet conection works fine with ethernet but ubuntu does not see my wireless network. card (RealTek RTL 8190 ID: 10ec:8190). Have searched this forum but unable to come up with a fix. I was looking for windows XP drivers to use Ndiswrapper but could not find a list of .inf files. My network is OK and works perfectly in windows and with my 2 laptops. Can anyone point me in the right direction? Additional info: install was done within Windows using WUBI to a separate partition on my HDD. I am new to this and thouroughly confused as to the procedure for installing the drivers if they are in fact available."
I am very frustrated in that I would like to use Ubuntu 10.04 but it is useless without internet connectability. I am new to linux and do not understand where to get the appropriate drivers or how to install them. I wish someone would answer this post and either give me a clue what to do or just say "give up" and uninstall ubunutu.
View 2 Replies
View Related
May 12, 2010
Im not able to establish a Wireless Internet connection in Ubuntu 10.04.
Ive tried these steps:
1. Wireless Internet did not show via the Network-icon. Only the 2 LAN-gates where shown
2. I installed the Windows Driver (net8185.inf) via ndisgtk package
3. After restarting the computer, 2 LAN-gates and 1 WLAN where listed via the Network-icon
4. Normally WLAN should automatically start scanning for available networks, but that didnt happen
5. When I tried to connect to my own network, the computer tries to connect for 1 minute and than stops because no connection could be established
6. A wired Internet-connection does not give any problems
Details:
- I first had Ubuntu 9.10 but I wasnt able to make a WLAN connection either. I followed the same steps. After that I upgraded to 10.04
- iwconfig in Terminal gives an IP-address which consists of 12 identical characters.
- lspci in Terminal shows these data:
01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02)
[Code]....
My questions:
- How to create an Internet connection via my WLAN-card?
- How to install the option to search for available networks automatically?
View 9 Replies
View Related
Jul 29, 2010
I am using a fully up to date openSUSE 11.3 and today, I decided to upgrade my KDE 4.4.4 to Factory. The update went without a hitch, everything continued to work, including all of the items in my workspace.So now I am running KDE 4.4.95 and it looks nice. I like the new System Settings where the advanced tab is gone and everything is presented in a single window.
The only snag I have hit so far, is that Knetworkmanager no longer displays the network that I am connected to when I right click its icon in the tray. The screenshot may make clear what I am talking about.I am currently connected via a wireless network, which nm-tool confirms. However, it is not shown in the Knetworkmanager menu.
View 2 Replies
View Related
Jun 8, 2010
When my router switches off... the wifi signals go off... then why the hell ubuntu keeps on connecting to that very wifi like hell and when doesnt connect shows the prompt to manually connect... with the wifi key already filled in... whats the use of saving the key when it has to ask the question from me either to connect or not?? and if its isnt available... just wait when its available.. and for the prompt,i have only option to cancel(because wifi isnt available at that moment if i select connect it again tries to connect like hell..which it cant) and if i cancel it wont auto-connect when wifi does get available! what the heck?
Windows has this done the right way... when the wifi isnt available.. it dissconnects silently.. and when it becomes available connects silently.. why isnt this been done this way in ubuntu??
Ive attached an image..one can see in the image that it says "authentication required by wireless network" when there isnt any.. as router has gone down!
And the second thing i want to report is that there is no way to report this bug from ubuntu... the launchpad.net talks of going through bug reporting process which is done against a definite package... now how does a user know which package would be causing this error?? there should be a more clear process of reporting such bugs to ubuntu team... which a common man using ubuntu( ubuntu says its most user friendly of all distros right?) can report..
View 1 Replies
View Related
Feb 11, 2011
I'm using Kubuntu 10.04.2 LTS on a Bangho laptop. Kernel 2.6.32-28-generic i686. My card is: Realtek Semiconductor Corp. RTL8187B Wireless 802.11g 54Mbps Network Adapter iwconfig wlan0 gives me:
Code:
wlan0 IEEE 802.11bg ESSID:"Default_WLAN"
Mode:Managed Frequency:2.442 GHz Access Point: 00:06:4F:8D:B9:AF
Bit Rate=1 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr: off Fragment thr: off
[Code]...
Usually when this happens, for 10 or 20 seconds it appears to be connected (i.e. the heart symbol is there) but I can't ping google or my router, then it "realizes" it's disconnected. It takes one or two attempts to reconnect successfully by pressing the "active" button. Meanwhile throughout the disconnections and re-connections the signal is very strong (98%).
I had the same problem with my old access point, at first I thought it was the cheap/old hardware, so now I bought an "ENCORE ENDSL-A2+WIGX2 | ADSL 2+ Modem with 4 Port Wireless Router". The problem persists only with a stronger signal.
View 1 Replies
View Related
Mar 14, 2010
I just loaded 11.2 & Kde 4.3. Installed both Kinternet and Kppp. My modem is a USR PCI HW modem 2976. Hardware Info shows it connected to /dev/ttyS4. I configured the modem with Yast as modem0. The user access box is checked for Kinternet Both Kppp and and Kinternet will dial out.
The connect response comes back from the ISP and either of the dialers will hang and the dial tone comes back. The firewall is showing modem0 in the External section. Nothing changes if I shut the firewall off.There's nothing in the dmesg I could find. Could this be a pppd permission problem?
View 5 Replies
View Related
May 16, 2010
I've my OpenSuse installed both on laptop and PC.
The kNetworkManager works well on the laptop both on user account and root account. It connects to my mobile broadband fine.
The problem appeared on my PC. When I log into root account - everything seems to be fine, It connects through knetworkmanager - The cellular connection gets activated, I see X and a heart near "Activated". root account reads my DNS'es from resolv.conf
When I only log into the user account (not as root), the knetworkmanager connects - but as I've checked - it seems that it doesn't use the DNS adresses I've entered in resolv.conf (netconfig_dns_policy is set to "") so I can manually add openDNS to the resolv.conf). It just connects -
I did CHMOD the files resolv.conf and config in sysconfig/network - no luck.
The only way to bypass this is logging to root first - connect there, then switch to user while staying connected... but I think it's an annoying solution.
logs contain this when connecting from user account:
Code:
May 16 10:30:52 jaychyl-1-linux pppd[24965]: Plugin /usr/lib/pppd/2.4.4/nm-pppd-plugin.so loaded.
May 16 10:30:52 jaychyl-1-linux pppd[24965]: pppd 2.4.5 started by root, uid 0
May 16 10:30:52 jaychyl-1-linux pppd[24965]: Using interface ppp0
May 16 10:30:52 jaychyl-1-linux pppd[24965]: Connect: ppp0 <--> /dev/ttyUSB0
[Code]....
View 9 Replies
View Related
Sep 6, 2011
I am currently running openSUSE 11.4 on my Toshiba A505 laptop. I'm not certain about the exact model number of the wireless adapter but I believe it's made by Realtek. It does not show up in my list of network connections in YaST so I assume I'll need a driver for it.
View 7 Replies
View Related
Jan 15, 2010
I've installed opensuse 11.2 on an old IBM thinkpad. The install went without a hitch and when I got to the desktop I inserted my Dlink DWL-G132 wireless USB adapter. Opensuse immediately recognised that a wireless device was attached and I could see my wireless network listed. I entered my WPA password and was able to connect to my routers configuration page by entering 192.168.0.1 in the URL bar of firefox. For some reason I am unable to navigate to any webpage. When I enter a URL firefox acts as though there is no internet connection. The only way I can get the internet on my laptop is to connect it to my router with a cable. I used a wired connection and ran the update utility thinking that perhaps an update would fix the issue but it did not. I know the adapter works because the laptop used to have windows xp installed and I could connect fine with that.
Does anyone here have any idea why I would be able to connect wirelessly to the routers configuration page but not to the internet? I appreciate any advice anyone may have.
View 9 Replies
View Related
Apr 27, 2011
how to connect to internet via ADSL,and wireless. i am writing all these frome windows
View 2 Replies
View Related
Jan 11, 2010
The card is recognized by Ubuntu 9.10 and I have it in the network manager. I followed one tutorial about creating an ad-hoc network and all looked good, until I actually wanted to connect (or to be more precise, my machine is a host for other computers). The wireless icon just loops endlessly, without connecting and eventually I get "Wireless network - disconnected" message.
So, the main issue here is - connecting! I just can't. Also if you know/have some good tutorial for ad-hoc,
Code:
ivan@ivan-desktop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"internat3"
[Code]...
View 2 Replies
View Related
Mar 31, 2010
I've just installed Ubuntu 9.10 in my laptop. Everything works fine except for my wireless. It works, but much, very much slower the through RJ45, which is perfectly ok. When using wireless i can't even connect to any online messaging service and I need to reload pages oftenly. My security setting is WEP 128 bits ASCII and since I'm trying to follow the format suggested on the thread "HOWTO post a Wireless issue" I'll try to provide the infos like requested on it. Laptop brand and model (I'm from Brasil, so it's a brasilian model)
Code:
Semp Toshiba IS 1412
Wireless Card
Code:
ID 0bda:8189 Realtek Semiconductor Corp. RTL8187B Wireless 802.11g 54Mbps Network Adapter
Interface
[code]....
View 9 Replies
View Related
