i have a big problem y have to make an alias for the eth0 interface, i made it with yast and my alias was eth0:1, first, if i try to shutdown the interface i cant it give an error and tell me that the interface dont exist and the second threat is if i can put a default gateway for this alias something like this in other distributions:
route add 128.26.6.11 gw 192.168.28.201 dev eth0:1
Quote:
-A RH-Firewall-1-INPUT -s 10.12.0.0/16 -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT
Ex- 10.12.0.0/16, 172.150.0.0/16, 192.168.20.0/24
How can we add multiple sources network address in the above INPUT chain?
My routing table does not get complete for some reason. I'm using a Huawei E220 USB modem on openSUSE 11.3 using NetworkManager to connect.When I connect to the net the routing table looks like
Code:
/home/freefox # route
Kernel IP routing table
[code]....
I'm trying configure my server for routing between vlans, but I'm having troubles with my server after that vlans are set. I can create vlans and routing is OK, but when I trying remove a vlan, restart the network script or restart the server, the CLI freeze and then I can't do anything. Even Ctrl+C or Ctrl+Z isn't work. I can use other terminal or do other SSH connection (if the network interface used by ssh isn't crashed), but if I try use a ifconfig per example, crash again. The unique solution is restart the server. Nothing about this is found in the log.
Opensuse 11.4
Kernel: 2.6.37.6-0.5-desktop
I just installed (n this 11.2 system) vmware server (v 2.02), to have access to a few small systems. One of them is a 11.1 guest which I just upgraded to 11.3, successfully (almost).
I have a problem, though: from the host I can not ping/ssh the guest.
Guest to host works fine (including names).
Code:
The firewall is down on both sides. I don't see anything with iptraf in the guest. The IP addres of the guest is correct, unless I'm too tired to see.
Why?
Code:
I'm going to an area with no wired internet connection so I would gather information on if it is possible and how to make working the following configuration for an home network:
a wireless access point connected to a laptop (an old one with a centrino Duo) with a usb stick for UMTS connection to the internet it is possible to use the laptop for routing to the internet the requests (http, ftp, mail etc..) of the PC connected to the home LAN which software have I to install on the laptop?
I would like to create several aliases to eth0, but have the addresses assigned by DHCP instead of being set to static IP's. Is this even possible? All the examples I've seen assign a static IP using the command:
ifconfig eth0:0 192.168.1.11 up
I setup a virtual server with these configurations:
1. Mail server: POSTFIX / DOVECOT
2. Webmin / Virtualmin
I am getting email to desired folders locally but I am not getting email from outside to desired users. Emails are bounced back with message "Address not found in virtual alias table".
Recent log errors are:
Sep 8 04:25:49 server1 postfix/smtpd[28002]: cannot load Certificate Authority data
Sep 8 04:25:49 server1 postfix/smtpd[28002]: warning: TLS library problem: 28002:error:02001002:system library:fopen:No such file or directory:bss_file.c:122:fopen('/etc/pki/postfix/root.crt','r'):
[code].....
what is the technical/non technical difference between quagga and zebra routing platform ? and if any one knows other open source routing platform other than quagga, zebra, xrop, vyatta.
View 1 Replies View RelatedI have tried using ad-hoc networking in linux machines. My question is that is the routing in ad-hoc network is implemented at kernel level. I just want get my hands on the code that make wireless ad-hoc networking possible.
View 1 Replies View RelatedIs there any possible way I could add loose/strict source routing for traffic originating from a host ? I mean to add certain hops I want my packet to pass.With iproute2 or maybe iptables ?
View 1 Replies View RelatedI am trying to configure virtual alias using regular expression.
For example :
Email send to user.1@example.com and user.2@example.com will deliver to user mailbox.
Email send to user2.1@example.com and user2.2@example.com will deliver to user2 mailbox.
And the numbers or alphabet in between user name and the domain will be vary , I can't just do a normal alias.
I been try to play around with main.cf and the virtual alias table but still not able to get work. So I am not sure is the main.cf didnt configure correctly or the regular expression is not working.
I have a Fedora box running a domain and a sub domain. It also is the mail server running Postfix and Dovecot. I have created a new user account in the Virtual Alias.conf file and run postfix reload.
"e.g [URL] admin_company"
This new account can send mail internally and externally but cannot receive mail internally and externally.
The error message internally is: 5.1.1 <admin@threadneedle.com.pg>: Recipient address rejected: User unknown in virtual alias table
I have the following setup:
Location A:
Internet -> ISP 1 -> Firewall 1 (external IP address) -> Web Server 1 (internal IP address)
Location B:
Internet -> ISP 1 -> ISP 2 -> Firewall 2 (external IP address) -> Web Server 2 (internal IP address)
I want to find out if I can failover to another location without having to make changes on the DNS server. Just by redirecting traffic from ISP 1 router to ISP 2 router.
How do I activate static DNS for mobile broadband. I can't find any place to write down this information. Settings are made in Network Manager - not Yast.
View 3 Replies View RelatedI am facing two issues with CUPS - 1. I have installed cups 1.3.9 over OpenSuse11 x86. Please check below -
cups:/usr/share/cups/banners # cups-config --version
1.3.9
cups:/usr/share/cups/banners # cat /proc/version
Linux version 2.6.27.7-9-pae (geeko@buildhost) (gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2008-12-04 18:10:04 +0100
I have added few printers over there and everything is working fine. I can also able to add - delete - modify any printers from "yast2 printer" command. I can also able to browse cups web interface via http://cups:631, but when I am going to manage the printers (start - stop - delete etc), none of the buttons are working in firefox5 not even in IE also. Older version of firefox is giving error as "This address uses a network port which is normally used for purposes other than Web browsing. Firefox has canceled the request for your protection." All other buttons are working properly.
2. LINUX - LINUX Printing - OK
LINUX - WINDOWS Printing - OK
WINDOWS - LINUX Printing - NOT OK
While giving printing from Windows machine (Printer attached on Linux), there is no problem to coonect the printers, but unable to print.
When I attempt to connect to a wireless network, the network manager asks me for the network's password, then says 'setting network address' for 20 or so seconds, then asks me for some random Hex or ASCII key in the same type of window I put the password in (Secrets for Noel -- KDE Daemon). Since a key is already typed into the window, I press OK, which then causes the network manager to go back to 'setting network address', then the window pops up again and keeps repeating itself.
I'm running Opensuse 11.4 with KDE, and my driver is ath9k. I don't know much about linux so please don't tell me to 'recompile this' or 'change this setting' without explaining how to do it. Please help, I've been unable to connect to wireless in OpenSUSE for 2 weeks now.
I've updated a desktop from 11.1 to 11.2 with the NET CD. After completion everything worked fine, though I have some issues with the NIC. been looking on the net and the provided solutions haven't been able to resolve the matter. After reboot I don't get an IP address, I go into Yast2 and network settings displays:
I have to delete the unknown device everytime after a reboot in order to get a new IP address. After that all works as it is suppsed to. I've been looking into the /etc/udev/rules.d/70-persistent-net.rules and deleted all that was in there,
I installed the Centos 5.5 and after the Xen. After I put a virtual machine named VM01.Initially it worked properly, I tried everything and it worked.When rebooted, I had problems with the network.I have two network cards eth0 and eth1, but eth1 does not have any ip and I use only eth0.The error that appears is:
vif0.0: received packet with own address the source address
I have two networks. One of them is wired, the other is wireless. The wired has an internet connection and a few other computers connected to it. The wireless network has a few hosts connected to it too, but it has no internet connection. What I've been trying, fruitlessly, to do, is make all connections that are bound to the internet, or my wired network, be routed that way, and all the connections to the hosts of the wireless network go that way.
Here's the setup..
Wired:
192.168.1.0/24 Gateway = 192.168.1.1
Route internet through here
Wireless
192.168.2.0/24 Gateway = 192.168.2.1
If my computer sends a packet to the internet, it should be routed through 192.168.1.1 If I send a packet to one of the local hosts of the wireless network, it should be routed through 192.168.2.1. Here's the routing table I've set up(This is one of many configurations I've tried)
Code:
$ ip route show
192.168.2.1 dev wlan0 scope link
192.168.2.0/24 via 192.168.2.1 dev wlan0 src 192.168.2.4
[code]....
With this, and everything else, I get destination host unreachable when pinging. The strange thing is that, if I unplug my eth cable, reboot and connect to the wireless network, everything is fine and I can access the router and the others. I'm trying to improve my networking skills, as I've had this of setting up a small linux box as a router for quite some time, for the fun of it, but I need to get routing under control before I go ruin my network.
openSUSE 10.3 is firewall with multiple public IPs, on one external interface..In protected zone is server with multiple LAN IPs, binded to different instances of Lotus Domino servers (irrelevant), and incoming connections are routed according to destination IP of incoming package to different LAN IPs(FW_FORWARD_MASQ set with "destination ip" parameter).I would get something like SNAT instead MASQUERADING for packages that are traveling from internal servers to Internet.
View 1 Replies View RelatedHow to set IPs address on my server using Linux Suse 10.0. Its an old system which was configured before, the type of the modem was changed were by i need also to change the some IPs on the server.
View 2 Replies View RelatedI installed 11.2 on VMware 6.03. My os is windows 7.When I try to go online a pop up showed up
View 1 Replies View RelatedI had 200 workstation with both Windows XP and SuSe Enterprise Linux. Sometime, a few clients can't get IP address from DHCP with SuSe OS. With the same computer, if I reboot and chose Windows XP, it work fine. The log message or the boot message was "No IP Address yet ...backgrounding". I tried to reconfig network device, restart services, change another port, change another line LAN, set static IP Address .... but there's no luck for me.
View 5 Replies View RelatedI am coming across a strange error with my gateway. When I do a "ping", this is what I get below:
k-63a5b848c6cb4:~ # ping simba
PING simba.gateway.2wire.net (192.168.1.69) 56(84) bytes of data.
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=1 ttl=64 time=0.041 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=2 ttl=64 time=0.029 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=3 ttl=64 time=0.023 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=4 ttl=64 time=0.015 ms
Is the gateway doing something strange?
I've just installed opensuse 11.2 with the network installation iso. During the installation, it has got the IP via DHCP without any problem, and I has downloaded all the needed packets without problems... But when the installation finish.I have no network connection It's strange, because I have IP address, I get the IP from the DHCP server, and I can see the IP addreess if I do "ifconfig", the default route and even the DNS servers in the resolv.conf file; but I cannot ping my gateway (that is the DHCP server as well!!), I cannot ping anything in my network and either anything in internet. I see a network error at the start, but it finally gets the ip address. In the dmesg, the last message repeats over and over. The machine is a Hyper-V virtual machine, but as I said... I worked very well during the installation, I don't know what is going on. I've tried to reinstall, but it doesn't make any difference
View 2 Replies View RelatedI would like to build a centralized address book for my SOHO server. Is that possible without the use of openLDAP (I would like to avoid that)?My clients will be:Thunderbird, KMail (for KDE 3.5) and webmail.If so, do you have any suggestions/Howtos?
View 4 Replies View RelatedI want to set my desktop IP address to always be 192.168.1.2. The NetworkManager connects to the network automatically and the IP address is assigned randomly. I can set up another connection in NetworkManager and always change over. But is there any way to make the default eth0 interface to be permanently set to a certain address (using NetworkManager, not ifup)?
View 9 Replies View RelatedI know this is a relatively simple problem but no matter what combination I try for my alias, I don't seem to be able to get it right! All I want to do is scp a file from my current folder to a location on the network:
Code:
scp filename username@computername:/folder1/folder2
This is the usual layout of the command that I use, so I thought that to save time, I would create an alias or even a function which did this for me, so all I had to type was
Code:
scp101 filename
and it would copy it to the set folder on the remote computer...
My attempt at an alias looks like:
Code:
alias scp101='scp !* username@computername:/folder1/folder2'
and I have also attempted a function:
Code:
scp101()
{
scp "$1" username@computername:/folder1/folder2
}
The alias tells me that filename is not a directory, which I assume means that I have some of the syntax wrong in the alias but I did a google search and I can't seem to find a decent example of what I'm trying to do. When I load up a terminal, I get an error message about the "(" of the scp101 function - so I've obviously can't get the syntax of that right either...
There is a cable plugged in to the second network card, but that interface is not configured. I'm getting a lotof "martian source" alerts because of this.If the interface eth1 isn't started because it isn't configured, why am I getting these messages?
View 2 Replies View Related