OpenSUSE Network :: Internet Loss When Changing Networks?
Mar 15, 2011
I had been playing around with wpa_supplicant, iwconfig and dhcpcd to get an x-less internet connection. However, this seems to have broken my Internet connection. I have reverted my wpa_supplicant settings, but every time I change networks, I must manually run
Code:
$ sudo /sbin/dhcpcd wlan0
in order to get a connection. Unfortunately, this sometimes results in
Code:
err, wlan0: timed out
warn, wlan0: using IPV4LL address ###.###.###.###
Using KDE 4.6 on openSUSE 11.4 32-bit. I want KNetworkManager to just automatically work.
Just today I installed opensuse 11.3 on my Compaq CQ61. Even though I am able to connect to networks (both with an ethernet cable and wireless) I don't have internet access. I have used opensuse for a very brief period in the past and I had no such problem.
I know Windows forward and backward but I am so new to linux it's just wrong. I just installed fedora (like 1hr ago) on and old toshiba laptop with a WiFi PC card. Everything seems to work fine except. My Networks connects to my home Wifi network but it will not connect to internet. When it connects the IP address isn't even close to being in the same range as my other laptops and PCs. Like I said I'm new to linux but I'm wanting to learn. Any fixes for this issue? Which linus book is the best one to read for a beginner? Other then not connecting to internet I have no complaints.
My wireless network doesn't work. I get no list of broadcasting networks. I have runned 'collectHWData.sh'. This is the output. Does anyone know what I should do to make my wireless work? The problem occurs on my clean installation of SuSe 11.3 on my laptop PC C500 Compaq.
Code: collectNWData.sh V0.6.5.4.1 (Rev: 1.282, Build: 2011/01/25 19:33:38 UTC) !!! CND0470I: Reduced analysis capability and less network information because script was
I have a DNS server (dnsmasq v2.55) at the center of three subnets: x.y.1.0/24, x.y.2.0/24 & x.y.3.0/24. dnsmasq does a grand job of issuing a suitable DNS server address with the DHCP option 6. So, machines on subnet x.y.3.0/24 are told that the DNS server is x.y.3.2, machines on subnet x.y.2.0/24 are told that the DNS server is x.y.2.2 and machines on subnet x.y.1.0/24 are told that the DNS server is at x.y.1.2. Even though the DNS server is the same box (although with three nics).
Now the question is: How do I make dnsmasq respond similarly to name resolution requests? So that when: Machines from x.y.3.0/24, ping <name of DNS server> dnsmasq returns x.y.3.2, Machines from x.y.2.0/24, ping <name of DNS server> dnsmasq returns x.y.2.2, and Machines from x.y.1.0/24, ping <name of DNS server> dnsmasq returns x.y.1.2.
Currently, the DNS server returns the IP address that is assigned in /etc/host. Which, of course can be changed, but via that mechanism, will always be wrong two out of three cases.
OpenSuse 11.4 Asus Netbook 1000H Following other members in the forums I have installed Opensuse 11.4 on the Netbook. In the early days Ubuntu Netbook Remix worked well for me. But this has been discarded, and the "one size fits all" Ubuntu had become slow and cumbersome. So..... onto my post. Opensuse is working well. The install went beautifully.
It detected the Wireless Internet and I am able to get on line. I also need to share the Internet connection to a desktop. This is done via a small network switch. Thus far I cannot do this. I tried to use ifup to configure a static ip but this busted my Wireless configuration. I went back to knetwork manager. Then I tried to set up the wired network using knetwork manager and under IPV4 "share" the connection. But this blanks out any possiblity of a static address and substitutes dhcp. My desktop cannot ping the this dhcp address. Ubuntu had this thing called Firestarter? - from memory. This configured the system to sharing the network.
Loss of internet connection after upgrade from 8.04 to 8.10 Like the title says, I lost my internet connection after upgrading my Ubuntu system from 8.04 to 8.10.I used the downloaded automated method. It appeared to work fine on its initial reboot into 8.10. But I noticed the internet icon indicated loss of connection. Even so, I was still able to browse the net through Firefox. But then when I rebooted the next day the opposite was true: the connection icon indicated connection, but Firefox would not actually connect, nor would update manager. It has been like this since. This is a dual boot machine, and the Windows XP Pro side still connects to the internet as usual, no problems.So how can I make my new 8.10 system connect to the internet?
A couple of years back, just getting into Ubuntu, I installed Firestarter as an option to aid in networking. Realizing that it really didn't help in my plan, I now want to remove it.In terminal, I typed:
Code: sudo apt-get purge -y firestarter I rebooted, only to find out that I now have no internet connection.
Not sure this right place for this. After updating from Ubuntu 10.04 to 10.10 lost internet connection - was instantaneous loss. Wired connection computer to router. Icon on computer shows "wired connection 'auto Eth0'active" The router shows line connected ok. Computer shows connection is established. Connection information menu shows details such as IP address broadcast address and other details. Where do I go from here to reconnect to internet.
once upon a time i manually entered my ISP's DNS servers in /etc/resolv.conf Now i have changed ISP, my old DNS setting are still present even though i have edited my resolv.conf file to my new ISP's DNS servers. Internet still works fine, i just want to use my new ISP's DNS as my old ISP will be closing its doors very soon. Am i doing something wrong, or better put.forgot to edit another file..? I did do this a while ago, so i apologise in advance for my incompetence. I'm stilling running 11.1 / Router has DHCP configured. my resolv.conf file is below
Code: cat /etc/resolv.conf ### /etc/resolv.conf file autogenerated by netconfig! # # Before you change this file manually, consider to define the # static DNS configuration using the following variables in the # /etc/sysconfig/network/config file: # NETCONFIG_DNS_STATIC_SEARCHLIST
I cannot uncheck the "Change Hostname via DHCP" box because it is disabled. Next to it says "No interface with dhcp". How can I fix it? I'm using OpenSUSE 11.3/KDE4
I installed Suse 11.2 on clean HD. I cannot connect to the internet. Seems like Suse didn't install drivers for on board ethernet card. It is a Marvell Yukon 88E8056. I'm new to this and don't know how to install the drivers.
I have SUSE 11.0 set up to act as a router/firewall for my home network to the internet through a cable modem attached to an Ethernet card. When I was laid off several years back, I found information that let me connect my network to an ISP via a standard serial modem. I am considering going to the Sprint U1901 4G USB modem and dropping cable internet. Sprint claims the U1901 is Linux compatible. My thoughts are that using the 4G modem should be similar to the old dialup modem. I had a script that connected to the internet whenever internet traffic was detected. Unfortunately, I did not save notes on what I had done to setup the modem to dial automatically, and I have been unable to locate information that seems good to set this up again. I already know that all I had to do to get routing working was simply replace the internet port in the firewall/routing script with the port for the modem. So I assume that is rather trivial.
Would you please point me to a doc, perhaps SuSE specific, that gives reasonable directions on how to set up a "dial on demand" ISP connection? I assume that the 4G modem will be very similar to my old serial modem so that a dial on demand script will work. I did find a dial on demand howto, however, it did not seem to apply.
I am using Suse 10 sp2. By running ifconfig I am changing the mac address. Everything is happening successfully, but this is adapter losing the network connection. Even when I give a static IP. I am not able to ping any other IP.
In short: browsing the internet with domain names does not work. The long version: I've configured my network with DHCP and ifup. Ping works on my internal net and with servers in the internet. Dig work's too! I get the right IP to the requested domain. When i try to access the internet using firefox or even wget i get an DNS error. For example wget is showing the following error: Resolving heise.de... failed: Name or service not known. wget: unable to resolve host address 'heise.de'
Again dig show me the right IP and if i add the entry to /etc/hosts it work's too! I've even tried it with manually setup of ip address, nameserver and default gateway but with the same result. Switching off the firewall has no effect on this problem, too.
I install from openSUSE-11.3-NET-x86_64.iso. Installation was succesfull, but after install all packet on test internet / update was error. And after log in in installed system internet not work. I use router with DHCP
I'm on opensuse 11.4 (11.3 won't work with my monitor).
My computer gets internet through wireless and I want to share that internet through its ethernet port. So far I've tried using Knetworkmanager to create a network bridge between my wireless and wired connections. I created a new wired connection and shared it using the ip address settings. I was able to get both connections active, but the device hooked up via ethernet had no internet connectivity.
I also tried this command: echo 1 > /proc/sys/net/ipv4/ip_forward
but another test resulted in the same fashion (no internet on wired). I believe anything I add to /proc should have an immediate effect, correct?
I have a desktop computer running OpenSUSE 11.2 with two network cards installed. I would like to use both cards for connecting to the internet using different networks. The setting would be the following: eth0 is the main (default) card, almost all programs should use this NIC for connecting to the internet. eth1 is used only by a few programs, which have setting for selecting which network interface to use. The two NIC's are connected to different networks, so the IP address of the NIC's, the related subnet masks and gateways are also different.
Saying short, I would like to have the two NIC's as they would be in two separate computers. I can set the IP address and subnet mask of the NIC's. The main problem is that I can only declare one gateway. How can i setup this? I do not use network manager, I configure network cards using yast, but if needed I can of course use ifconfig directly.
I'm having a strange problem with my network connection/DNS. I turn computer the on and it recognizes and connects to wireless or wired but I can't access any Internet resources or my router. If I ping the default gateway, I get no response and I get DNS errors from any network services that run at start up. If I stop and start the network daemon then it all works fine until the next time I turn on my laptop. It does this for both wireless and wired connection.
I've tried to edit the network interface information in YaST but it says that configuration is handled by knetworkmanager and I have no idea where that information is accessed. I should point out that it all worked fine until I tried to connect to open WAP at my school and couldn't so I connected to the wired network. Next morning I had this problem when connecting to my home network. My questions are 1. What could be the cause of this error and 2. where does one configure the network interfaces when using knetworkmanager
I often use an Ethernet cable to connect my computer to another computer for various purposes. But when I do that, I cannot use the internet even though I'm still connected to a WiFi access point. I'm presuming that's because openSUSE is trying to reach the internet through the Ethernet cable, which has precedence over WiFi.Is there a way to enable internet usage via WiFi while I'm connected to another computer over Ethernet?
I first tried an upgrade from 11.3 to 11.4 and lost Internet Access, so i re-loaded 11.4 from scratch on clean partitions.
I am connected to my wireless WPA2/PSK connection, have an IP, am able to see the network.
I turned off and disabled the SUSE firewall.
I tried setting Firefox proxy settings to auto and to none, i dont use proxy.
I am currently posting this through an SSH connection to my 11.1 server from the new install of 11.4 on a Dell latitude D600 laptop (not using the on-board Broadcomm that is an issue for a later date).
I am using Maverick on a Dell Vostro 3400. I recently installed ConMan network manager and it worked flawlessly in my office and home. I had to travel to Virginina and Pennsylvania and ConMan continued to perform. However, when I returned to my home and office, I could not connect to my WiFi regardless of what I tried. The instructions, from the Web, that I used to install Conman also had uninstalll instructions that promised to return my network manager to its previous state. I uninstalled Conman and have not had any network activity since - no network of any kind. What to do to return to Network Manager?
I try to setup a locale network between 10 (Web) Servers (openSuse 11.2), each Server is connected to the internet (eth0) which works fine on all servers.
A 2nd NIC eth1 (1GBit rtl-8169) on each Server is connect to a Switch and should function as a LAN. I installed/configured the 2nd NIC with yast, and than added a route for the local network (192.168.20.0) to use eth1. So far every thing works (ssh for example), but I have a packet loss of 10%-60% (ping) on the local network, and I cant find the reason for the packet loss. I already installed a Debian Lenny on 2 Servers (just to test) but I have the same problem on Debian.
No firewall or any other application is in the way. With tcpdump I could figure out that the packages are send but never show up on the destination server.
I put some more information about how I configured the LAN below. I have not done this my first time and from my experience if something is wrong with the network configuration (wrong routing, firewall in the way, etc.) this usually leads to a packet loss of 100% or the destination is simply not reachable.
The 2nd NIC is installed with either yast on suse , or by editing /etc/network/interfaces on debian. The Kernel module rtl8169 is loaded.
the thing is that I cant use Network Manager to connect to Internet, because it simply do not connect. The connection, although, awailable throught yast when i choose "traditional method with ifup", so everything is just fine, but if i need to reconnect, i have to reboot. How do I setup a !working! connection through Network Manager, or maybe i do not do something properly.
I'm new in SUSE 11.4. My problem is: I'm using Alfa AWUS036H card. It's recognised and I can establish connection to my network, but cant get to Internet. I can't surf the web cos Firefox tell me that connection is timed out. Now I'm confused why I can't surf the web even if I'm connected. Also, I trayed to instal linux drivers for this card folloving Ubuntu "how to" and it just dont work.
I'm using kubuntu 9.10 desktop edition as a server and I set the IP statically, what happens is that when I ping it from another machine on the same network, I get intermittent packet loss (up to 80% and sometimes even higher). When I ping any other machine on the local network everything's fine with 0% packet loss. Packets go directly through switch, no router or anything in between.
I suspected wiring issues, but that doesn't seem to be the problem after I changed the wiring. I was connected to wireless and suspected that but no go either. Same thing when I turn wired. I just changed the ethernet card suspecting drivers but that's no good either. Iptables is a cleanslate installation, it's totally empty.
I have been having this problem for about two weeks now where Debian's network and internet connection randomly fails. It works perfectly fine and hosts all the services I need for a while, and then without warning all network connectivity fails. I can't ping any other network device. Regardless of how much I try to fix it, the only thing that works is restarting the computer. First, the server went 7 days without a problem; then 5 days; now it lasted 2 days. Judging from my Teamspeak server logs, it crashed today at 12:31. I grep'd through my log files and found this information:
I have a fileserver running openSUSE 11.2 and samba services for file access from MS Windows based workstations. My question relates to changing default permissions on files and directories created from the windows clients.
Following are extracts of the /etc/samba/smb.conf file :
Even with the above entries, sometimes there are files and directories created by the windows clients having permission
