OpenSUSE Multimedia :: Hauppage Nova TD500 "unable To Find Firmware"
Jan 9, 2011
I have encountered a problem when trying to create a Myth .24 setup on a fresh, clean OpenSuse11.3 installation.
I have installed the OS and then installed Myth (using packman repo) and started to configure it (ie created the DB and the specific Myth schemas) however when I try to configure the card I am told "Unable to open the device".
I am far from an expert here but found that if I do lsusb and dmesg | grep dvb, I can find a little more about the problem ...
Code:
bgrsvr-u:~ # lsusb
Bus 002 Device 002: ID 2040:8400 Hauppauge
bgrsvr-u:~ # dmesg | grep dvb
[ 11.271382] dvb-usb: found a 'Hauppauge Nova-TD-500 (84xxx)' in cold state, will try to load a firmware
[ 11.271388] usb 2-1: firmware: requesting dvb-usb-dib0700-1.20.fw
[Code].....
View 1 Replies
ADVERTISEMENT
Sep 18, 2010
Installed Mythbuntu today. Spend hour over hour trying to get MythTVto work together with my Hauppauge WinTv-NOVA-HD-S2 card. I've followd so many wikis, reinstalled, tried again ... no success. The card itself works fine. I can use it with MeTV or on Mplayer - no problem. I managed to create a channels.conf. Also no problem. MythTV recognizes the correct card. I have set it to LNB. Now in the backend setup I cannot manage to get the card to scan. And if I try to point it to the channels.conf I am also getting an error message (Failed to open '%1'.
View 2 Replies
View Related
Jun 28, 2011
I want to know how to find out what firmware version is on my optical-drive. And also if an update is available, how to update the firmware.
View 4 Replies
View Related
Feb 13, 2010
I have Ubuntu Karmic 9.10 with this card, its just works without any configuration but I have a big problem.
I start Kaffeine 1.0-svn3 and I can see the last dvb-T channel but when I want to change to other channel I can't see it, I have to restart Kaffeine, or wait to get the "Read error from:" error press Ok and select the channel.
View 7 Replies
View Related
May 2, 2010
Actually,my ubuntu 9.1 was running smoothly but now it gives a message to install b43 firmware and a site name to install it.I could have installed it but ubuntu just get stuck after that message.Is there anyway to install through windows?
View 1 Replies
View Related
Jun 16, 2011
I am trying to get a Hauppage Win TV DVB Tuner Card working in Ubuntu 11.04 Desktop 32bit.So far when running the scan tool from dvb-apps I get the following as an example:
>>> tune to: 697833000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_3_4:FEC_AUTO:QAM_16:TRANSMISSION_MODE_2K:GUARD_INTERVAL _1_32:HIERARCHY_NONE (tuning failed)
Though I installed the driver from 'Additional Drivers' and dmesg gives me:
[ 9.455847] lirc_dev: IR Remote Control driver registered, major 249
[ 9.457078] IR LIRC bridge handler initialized
[Code]...
View 1 Replies
View Related
May 1, 2010
Just installed Ubuntu Netbook Remix 10.04 on my Acer ao532h netbook.I did a clean install, but I had been running UNR 9.10 for some time without a hitch. The new version fixed a slight bug that had made it necessary to tinker with the wifi adapter in the old version, and also seems to boot faster as advertised. However, there is one slight problem with the new version: when I attempt to engage visual effects in the appearance control panel (something which worked in the old version), the options are grayed out, as if the video driver is not installed. When I go to the hardware drivers panel, it doesn't detect any drivers to install. As far as I can remember, I didn't have to install any drivers for the GMA 3150 graphics card in the old version of UNR.
View 4 Replies
View Related
Mar 5, 2011
I can't install the wireless firmware for Ubuntu 10.10, I don't have a LAN connection.
View 2 Replies
View Related
Feb 28, 2010
I have given up trying to get the hauppage 950q to work on ubuntu 9.10. I just cannot get it to work. tried kaffeine, tv time, tvhead, mythtv and none of them work. So before I return it I wanted to know if it could work under a virtual machine (tiny XP). Has anyoe tried it? Also what VM do you recommend to be able to get the usb connection to work out the box?
View 1 Replies
View Related
Oct 16, 2010
Reading this: SDB:Live USB stick - openSUSE
I did zypper in imagewriter,
Code:
Loading repository data...
Reading installed packages...
'imagewriter' not found.
Resolving package dependencies...
Nothing to do.
View 7 Replies
View Related
Oct 24, 2010
Problem in Natty Narwhal - 11.04 with the Broadband 43xx Wireless Card: Unable to download firmware for wireless. (Also works for 10.10 and 10.04) From the 'Additional Drivers' section: Quote:
This package contains Broadcom 802.11 Linux STA wireless driver for use with Broadcom's BCM4311-, BCM4312-, BCM4313-, BCM4321-,BCM4322-, BCM43224-, and BCM43225-, BCM43227- and BCM43228-basedhardware. Possible Solutions: Solution 1: System > Administration > Synaptic Package Manager > Search: firmware-b43-lpphy-installer > Click Mark > Click install > Close
Kontza found the solution (post #3), so thank him for it. This solution fixed this problem on my Dell Inspiron 1545 with a Broadcom 4312 card. (Card Tech Specs: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)) Solution 2: Another option is here. Update: The Live USB of Natty Narwhal (11.04) automatically detected that I needed the STA driver. After installing it and rebooting, the wireless worked. (No cable was needed for this.) Update 2: After installing with the alternate cd, I needed a cable and after updating, I was able to download the STA driver through the 'Additional Drivers' section.
View 9 Replies
View Related
Oct 5, 2010
I have a Linux based board which has one serial port (so, stdin == stdout == stderr == /dev/ttyS0). I want to send Firmware over a serial port using Y-Modem protocol. But, when I poll on given fd (after sending ASCII 'C') its got time out. I am using HyperTerminal which is connected to my board's serial port. So, neither the HyperTerminal (only when it has launched dialogue box to send firmware to the board using Y-Modem) able to read data send by the board nor board able to read data send by the HyperTerminal. But when I type on HyperTeminal then the board got the key-strokes (thats why I can atleast browse through the GUI).
The same serial port is being used to render (VT100 based) GUI. I have managed to disable printk(s) after user-mode is up & running.
View 3 Replies
View Related
May 3, 2011
Banshee can't find any information about track or artist with a CD in the drive. She can play it and rip without error just no info... I have had a good look about the menu's and can not find any way of changing the site where it gets the info from.
View 4 Replies
View Related
Nov 27, 2010
i have a hauppage wintv usb2 tv device, works with windows OS, i want to watch live tv using this.
View 2 Replies
View Related
May 1, 2010
I try to find a rpm for kmplayer from here, but there are all for KDE? Software.openSUSE.org I am using opensuse 11.2 + Gnome desktop, which rpm should I use?
View 9 Replies
View Related
Jul 23, 2010
I'v been unable to set the screen saver timer since I can't find it. I'v tried the suse wiki, no info. Right-clicking the desktop or Admin Yast doesn't have it. Where are the timer settings?
View 3 Replies
View Related
Sep 28, 2010
openSUSE 11.3 question:
I have a PCI parallel port adapter (Syba SD-PEX-NM1P) that should "only" need to be told what ports and irq to use with parport_pc but, for the life of me, I can't make it happen. Using lspci -v, I can see it uses irq 19 (it that 19 or 0x19???) and ports 0xc800, 0xc400, 0xc000, 0xb800, 0xb400 (all 8 bit), and 0xb000 (16 bit). This is confirmed by the YaST2 hardware information tool.
Doing modprobe parport_pc io=0xb000 irq=0x19 should do something useful but I get no result at all. There is no /dev/lpt1 - a /dev/parport(n - where n is a digit) shows up on occasion but I can't figure out when it appears or why. cat foo >& /dev/parport(n) - where foo contains "hello world <FF>" doesn't do anything on the printer. Using the YaST2 printer tool, even the HP tool (the printer is an HP LJ-5P), is fruitless.
View 9 Replies
View Related
Jun 17, 2011
I tried to implement the solution given at: [URL] on a Dell Inspiron 1525 laptop, running Ubuntu 11.04. However, I still can't connect to wifi.
I can see that the files were extracted inside /lib/firmware/ (I see a b43 and a b43 legacy folder).
The lspci -vnn | grep 14e4 returns:
Code:
0b:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01)
View 9 Replies
View Related
Jul 22, 2010
I've recently switched over to gnome desktop environment with gnome-shell preview as my compositing manager.Everything is good except for this process xfce4-notifyd which autostarts somehow..
The problem with this process is it acts as the default notification daemon over-riding gnome-shell's built-in notification support and tends to display balloon popups on the top right corner....If i kill this process everything is good.... But on restart it autostarts again somehow..I looked through the items in gnome-session-properties and also in these places:
Code:
/usr/share/autostart
/etc/xdg/autostart
But couldn't find any entries related to xfce4-notifyd.
View 2 Replies
View Related
Oct 12, 2010
After digging around in vain in my local .kde4 I am unable to find where the RSSNow plasmoid stores the feeds. It apparently wants to keep them secret forever.
(Man - Plasmoids are okay, but the utter lack of documentation for them makes them far less useful than then could be.)
View 3 Replies
View Related
Oct 29, 2010
I downloaded some application for Linux (program microcontroller LPCXpresso). When I trying to install it some error appears
Code:
Can't find a usable init.tcl in the following directories:
/installkitvfs/lib/tcl /installkitvfs/lib/tcl8.6 /home/damon/src/installkit-1.3.0/out/lib/tcl8.6 /media/lib/tcl8.6 /lib/tcl8.6 /media/library /library /tcl8.6b1.2/library /tcl8.6b1.2/library
This probably means that Tcl wasn't installed properly.I think Tcl is installed, maybe I need to reinstall it if so, how? What I need to do?
View 8 Replies
View Related
Jul 16, 2010
I had dual screen config (large desktop) going on 11.2 with proprietary nvidia driver without problems. After upgrade to 11.3 this didin't work. I was not able to find a way to configure nouveau drivers, and it was stuck in the 'twinview' mode, so decided to install binary nvidia instead (the 'hard way'). Took me a while to figure out 'nomodeset' thing, but in the end drivers were installed successfully. The problem now is that only monitor displays anything, and I can't find the nvidia control panel to activate second monitor and extend the desktop there.
Used to be able to install nvidia control panel easily in 11.2 with one-click install, but for 11.3 the page says that the one-click install buttons aren't ready yet (SDB:NVIDIA drivers - openSUSE) So my question is 'how to get dual screen going and extend my desktop to second screen using 11.3 and nvidia 210 card' ? And I don't care whether it's nouveau or proprietary drivers, as long as it's easy to configure and it works.
View 3 Replies
View Related
Aug 12, 2010
I am trying to update four OpenSUSE 10.3 servers. This worked once on one server, but I have been unable to repeat that success. I use yast's Online Update to select repositories, but at the end of the repository refresh they keep coming back with 'No active update source is available. Exit Online Update now?' I get this error:
Download failed: File /repodata/repomod.xml not found on media: [URL]
It appears to connect to remote repositories, but always fails. Is it realistic for me to expect to update 10.3, or is it a lost cause? I am not ready to jump to 11 yet, but I am required to update them. I am a newb, so I am not clear on the process. Are package versions locked in place for specific versions of OpenSUSE? If so, how can I find out what the final versions were for 10.3 so that I can at least tell my auditors that they are as up-to-date as they can be?
View 9 Replies
View Related
Jun 4, 2010
I have ldap authentication working and the machine is joined to the domain, but I have to append the domain name to my login every time I log in. example: user@domain.I've been unable to find away to log in without appending the domain name to the username. Any ideas on how I can force the machine to automatically append the name for me?
View 2 Replies
View Related
Sep 18, 2010
I want to share files from my opensuse 11.3 laptop and Windows XP desktop. It works well between Vista and XP. The domain name is WORKGROUP I checked everything: firewall Opensuse (open ports), firewall XP (disabled), XP workgroup name (WORKGROUP), opensuse Samba workgroup name (WORKGROUP) And my domain controller is set to "Not a DC" Still when I launch network in Dolphin I get "Unable to find any workgroups in your local network"
View 9 Replies
View Related
Dec 29, 2010
I can not install a driver for device EDUP WU2070. I have a disk with a driver for linux general. I don't know how to compile a makefile. My OS 11.3v doesn't see a device.
But when I run in Live CD mode all drivers install automatically and my WI-FI device work properly.
View 9 Replies
View Related
Oct 11, 2010
1. Unable to find frequently used Special Characters and Symbols in Novell openoffice writer. 2. How to import more symbols for writer while using Special Characters in Writer.
View 9 Replies
View Related
Jan 12, 2010
Code...
To find the appropriate firmware without knowing the make or brand of your wireless chip, you can use the command:
#fw-detect
But apparently debian package do not offer this useful tool, well, certainly for sidux exclusively.
Is there a package of fw-detect eventually?
View 5 Replies
View Related
Jul 4, 2010
I can't my system because of this error: Code: linux-firmware: /lib/firmware/radeon/R700_rlc.bin exists in filesystem Note that in the beginning, it asks:
Code: :: Replace kernel26-firmware with core/linux-firmware? [Y/n] There are so many updates by now that the list fills in a few pages in the terminal! Also, I wonder why so many Arch updates get stuck or broken compared to almost any other distro? Is it poorly designed packages? Is it a design flaw in pacman/the package format?
View 6 Replies
View Related
Jun 4, 2011
after installing Ubuntu Natty Narwhal 11.04, I'm experiencing tons and tons of complications with the wireless Internet connection. I have solved most of them. Now I have only one thing left. When I hit the drop-down menu for wireless connections, it says "Wireless connection (Firmware missing)"
I have installed the driver for my wireless card but what is the firmware? I honestly don't know what it is although it's very basic. I have a Broadcom 43xx as my wireless card (specifically 4306). How do I get the firmware for it? Do I find it in Windows? Also I cannot get b43-fwcutter because I have absolutely to Internet connection on Ubuntu. To post this, I'm using Windows.
View 4 Replies
View Related
