I installed F10 today. From live-usb wlan worked fine, but after installing it doesn't find any networks. I tried to google this problem, but everybody says wifi works out of the box. Not for me.
Solved: I disappled wireless networking and appled it again. It found all networks.
I have installed Fedora 12 on my laptop.Installing my Broadcom BCM 4312 wireless drivers works just fine, but after a reboot I have to reinstall them. modprobe wl, modprobe wlan0 etc doesn't work either. I need to reinstall them every time I reboot.
View 7 Replies View RelatedI have just updated KDENetwork to this level and now my F10 doesn't find any wifi connection. By the way, I have been working with F10 for some months without any problem on wlan.
iwconfig now says:
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
[code]...
On my HP TX2500 laptop, dual-booting Vista and 9.04, Ubuntu installation found the WLAN and it works fine.I installed VirtualBox with Vista as the host and 9.04 as the guest. Wired Ethernet works fine but it didn't seem to find my WLAN. What more do I need to do?
View 1 Replies View RelatedWhy doesn't encrypted WLAN communication work for me? I've got an HP Probook 6555b with Ubuntu 11.04 32-bit. When I set my WLAN router to unencrypted I'm able to connect. But if I choose WPA-PSK-TKIP or WPA2-AES or WPA-PSK & WPA2-PSK I can't connect. Ubuntu prompts me to enter my encryption key. I enter it. It runs for a while and then prompts me again. The little icon at the top right of the screen next to the speaker symbol is where I can see it trying to connect.
View 2 Replies View RelatedI have an Aspire 7741z running Ubuntu 10.04 I just loaded the 32 bit version today, then did the Update manager (398 updates) Before the update everything worked fine. After the update, no wireless. Password & security is correct, all wireless setup is correct. Aside from my network, I do have access to a local hotel (next door) and I can always get into their unsecured guest network, that doesn't work either.
I believe it is the driver since I have loaded Ubintu 10.10 32 bit with the same reaction. It will connect when I put in the live disk, but not from the hard install. output from lspci
[Code]...
I just found it out now, after installed the skype and tried setup my web/audio on it, the webcam works fine but the mic doesn't work, so i went to the audio menu on fedora 14 and found it out the mic is dead.Someone had the same issue? Can someone let me know what can i do to fix that?
View 14 Replies View RelatedI have an Acer Aspire One 110 with Ubuntu 10.10 Netbook Edition, after i upgraded to 10.10 the wireless network connection is lost about 10 minutes after login, and I can't get it back without rebooting.
ifconfig
eth0 Link encap:Ethernet HWaddr 00:1e:68:9d:6c:c7
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[Code]....
My laptop is the one mentioned in the title. And it's completely offline at the moment.
Code:
$iwconfig
lo no wireless extensions.
Seem to have some troublesome chips.
Code:
$ lspci
03:00.0 Ethernet controller: Atheros Communications AR8151 v1.0 Gigabit Ethernet (rev c0)
05:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01)
code....
although in my case they should be for the 2.6.33.3-85.fc13.x86_64 kernel.
And I've been searching that repo for ages now, and I can't seem to find anything with kmod-wl or broadcom in there. I'm well aware that this is most likely because of my own ignorance as to the build up of said repo.
My net-book is working properly with Debian squeeze 2-6-32-5-686, only the wlan does not work. After typing lsusb I have got the message: lsusb : Bus 002 Device 002 : ID 160a:3184 VIA Technologies, Inc. VIA VNT-6656 [WiFi 802.11b/g USB Dongle]
So I obtained the driver package : VT6656_Linux_src_v1.19_12_x86. I followed the instructions ( make install... ) - but the result is only a lot of error messages. Mayby I am using the wrong driver package for the squeeze kernel - I don't know.
recently I risked a look to the Linux world and I'm happy so far, but now I've got a Problem, I'm unable to solve by myself. I installed Mint (Julia) on my old Laptop to test Linux. The Laptop has a very old PCMCIA WLAN Card with a Realtek rtl8180 chipset. Everything seems to run perfectly so far with one exception: the WLAN doesn't find any Network to connect although the card and the driver seem to be installed correctly.
Here some code from the terminal:
Code:
lspci
00:00.0 Host bridge: ATI Technologies Inc RS200/RS200M AGP Bridge [IGP 340M] (rev 02)
00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 340M]
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:03.0 Modem: ALi Corporation M5457 AC'97 Modem Controller
[Code]...
I have a Broadcom B4312(I believe) wireless card and installed the drivers for it, but under the Wireless tab in Network Connections, it doesn't show "wlan0" or anything similar to "eth0"(which it shows under "Wired"). I ran iwconfig and this is what I got:
[Code]....
I installed opensuse 11.3 succesfully on my acer aspire 5670 (5672) laptop. Everything works except wireless connection. Looking for a solution is follewed the " My wireless doesn't work - a primer on what I should do next" guide on this forum. These are the results i become: (2) Determine what device you have.: 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
[Code]...
my network was a dream to set up under ubuntu 9.10. all i had to do was enter pass key, then that was it. Works brilliantly.
Different matter with studio. The thing I notice in network connections is, it doesn't want to retain my pass phrase, if I go back into properties the phrase is blank. As far as I can tell the wireless card has been reconcognized and is communicating with router.
My system is: asus p5ql-vm epu, intel core2 duo 2.8 e7400, 4gb 1067 ddr2 ram, belkin f5d7050 v4000, edimax router.
Here is the info requested in the sticky:
kevin@ubuntu:~$ lsusb
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 003: ID 045e:00dd Microsoft Corp.
Bus 008 Device 002: ID 046d:c501 Logitech, Inc. Cordless Mouse Receiver
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
code....
I just installed 9.10 on a brand new Dell Vostro 1520. The WLAN card does NOT work out of the box.
Here is what you have to do.
After install and rebooting insert the live CD
Go to software sources (system > software sources)and check the "officially supported restricted copyright" box
You are then asked to update the available software list, do so.
You will receive an error message since you are not (yet) connected to the internet and all the other repositories are not available.
Now you should be notified that restricted drivers are available, if not you can go to system > hardware. Anyway, now you should be able to activate the Broadcom STA driver. After rebooting you can connect to available wireless networks.
Alternative (in case you are not asked, which happened to me on another Vostro system) system>administration>syaptic package manager
Search for broadcom
Mark b43-fwcutter and bcmwl-kernel-sources for installation
Reboot (who said there is no rebooting required in linux)
The adapter should be up and running ...
I have a Dell WLAN 1397 Half Minicard, 802.11 b/g card in my laptop, and I can't seem to get ubuntu to work with it. I tried this method:
1. Synaptic Pack Manager
2. Check "Install from Boot Disc"
3. Reload
4. Install and apply bcmwl-kernel-source
5. Reboot
This didn't work for me, so I tried entering sudo apt-get install bcmwl-kernel-source and that also didn't work. Another thing I tried is formatting my Ubuntu partition and reinstalling, and retrying both of those methods. The ethernet port does work, however.
Fresh install Ubuntu 10.10 on Acer Aspire 5050 with new hard drive. I struggled to turn the Wifi's button turn on but led light always on. It does not detect wifi driver. I installed ndiswrapper to get Acer's Winxp driver: netathr.inf by Windows Wireless Drivers from Ubuntu Software download. It's same thing as ndiswrapper.
[Code]...
My Acer Aspire one D250 laptop running Ubuntu 10.10 wireless does not work. I dual boot with Windows XP BUT windows XP wireless works fine. here are some details you might need.
[Code]...
I can't get my wireless card to work. I downloaded a broadcom driver for it and i do believe its the right one, but its not helped. I'm running mint 8. The information on my internal wireless card i got using the terminal is:
lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 760/M760 Host (rev 03)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SG86C202
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS963 [MuTIOL Media IO] (rev 25)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
[Code]....
I've just worked out how to get the wireless card working with an Acer Aspire D260 wireless card to work.
Enter terminal command;
sudo apt-get install wifi-radar
Then reboot ubuntu 10.04 after it has installed, network manager should now detect wireless networks in range and allow connection, right click network manager icon and select "Enable Wireless" or "Disable wireless" as required to turn on or off. So many others have had problems getting the wifi to work with Acer Aspire D260 netbooks and ubuntu 10.04.
I am trying to traceroute to google.com
When i do it looks like this
Code:
It does this no matter what site I go to. also the 192.168.16.10 is the untangle server
The command does work for local Ips
Code:
Networking on Fedora 11 doesn't work for me on various machines. Fedora 10 does, but only if you don't do an update.Why does Fedora get worse the more you keep it up-to-date?
View 1 Replies View RelatedI have a Samsung N130 with a Realtek 8192 wifi card (possibly 8192e, I'm not sure) and I am trying to run Fedora 12 on it. I used to run Ubuntu until trying their latest beta and realizing it's not very good, so I looked for something else. Ubuntu was at least easy to get the wifi working with just a few quick commands that were written out, word for word, in order, on the Ubuntu forums. I tried openSUSE on here and it didn't have wifi working out of the box either but people on their forums refused to give me actual instructions and just kept bumping me from thread to thread with people giving vague advice or else just telling me I was looking in the wrong place. I'm hoping that someone can give me clear and detailed instructions on how to get this wifi card working. Keep in mind that I am coming from Ubuntu and so I'm not super comfortable in CLI, if I need to do some CL stuff I will need clear and detailed instructions on how to do that.
View 4 Replies View RelatedI recently installed Ubuntu 10.10 onto my Acer Aspire D260 netbook.I find it much easier to use than Windows 7.Everything has been working fine until I recently tried going on the internet via battery power instead of my A/C charger. My update manager is showing that I am up to date and Additional Drivers is showing that the Broadcom STA wireless driver is installed and in use.
View 2 Replies View RelatedI'm runnig f 13 on my laptop, and it runs like a charm. But once in a while, the internet doesn't seem to work properly. It mostly works, but right now i am unable to reach certain pages such at google (which is annoying), whereas other pages like yahoo and this one works perfectly well.
View 2 Replies View Relatedhow nobody else could have run into this in the meantime. [URL] Two friends of mine are having the same issue on Ubuntu-11.4-machines. In short: Connecting to the Cisco-VPN via shell-command "vpnc" works flawlessly, whereas NetworkManager just doesn't connect at all. We had this working in older versions of Fedora/Ubuntu about some months ago...
View 9 Replies View Relatedi compile from broadcom wlan driver,when i use default F15 kernel (clean install F15)
Code:
$ uname -r
2.6.38.6-26.rc1.fc15.i686.PAE
[code]...
F13 on a EEEPC 1000HD.I have big problems with my wireless card. lspci says:
Code:
01.00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
I can't use Network Manager (it continue to ask me for the WPA password9. So I stopped it and I use command line, following this: [URL]
From the log I can see that it tried to associate to AP and after a lot of tries: it connects BUT the connection is really SLOW and UNSTABLE! (pinging hosts on the same network gives me about 50% packets loss) I am worried about this entry in the log:
Code:
ath5k phy0: unsupported jumbo
I am going to try to install madwifi, but before that I'd like to have your opinion and listen your experience! I see a lot on infos about ath5k, but I'd like to be pointed to the right direction!
Struggled a little to get Broadcom driver working with my Dell laptop. But I am at a point where if I manually type 'modprobe b43' the wireless works. If I reboot, it doesn't work automatically and I have to 'modprobe b43' again. Any ideas what I am missing here?I can't seem to figure out how to get this to work automatically. I did check to activate device when computer starts in network manager
View 1 Replies View RelatedI cannot get static addresses to work on eth0 and eth1. eth0 seems to use DHCP while eth1 uses the static information. Sometimes the static info is used but the interfaces get the addresses reversed.
From /etc/sysconfig/network
NETWORKING=yes
HOSTNAME=mosaic
[code]....