I have a network printer which is on a windows domain/workgroup. Earlier I use to connect to the printer with URI socket://10.x.x.x:9100 and it worked fine. Then I after some time the going got tough and at the moment I am not able to print.
Initially I thought that I need to upgrade CUPS and even downloaded its latest version (did not installed it though).
My trouble shooting started with the ping then telnet followed it. Following is the output of telnet
Code:
****@linux-rafr:~> telnet 10.x.x.x 9100
Trying 10.x.x.x...
Connected to 10.x.x.x.
Escape character is '^]'.
Connection closed by foreign host.
****@linux-rafr:~>
I tried to telnet by turning off the firewall but no good. Hope someone has a solution to this issue.
BTW when test page print job is viewed in CUPS the following is the message.
I have just got my network to work on Fedora, and now I have run into an new problem... I can't access any shared files or printers. The computer that has the printer and the files I want to access runs windows XP Home edition, and when I boot into XP on my machine, I can access the files and printer. Can this be fixed, or is Fedora incompatable with Windows XP in this case?
I'm having some problems with sharing my printer via SAMBA. Connected to my Ubuntu 9.10 Desktop is a HP office-jet D135 witch I shared via samba. I have no problems printing from my Ubuntu laptop. And in Vista I can see and access all the other shares, including the printer. But ones i try to access the printer I get a pop-up window telling me: "unable tot connect to printer error code 0x00000709 check if the name is correct or if the printer is connected to the network" ( but of course in Dutch). What is going wrong here?My /etc/samba/smb.conf
Wireless issue with printer.Can't connect wirelsess to printer(Canon MP640).Running Ubuntu 10.4 in 64 bit mode.I am able to connect with my small home network and INTERNET is running OK.When I try to add a printer,I just do not know enough.Also,cannot find suitable driver.
I am unable to connect to my printer wirelessly. I get this: Idle - "Connecting to printer..." The computer never connects. I can print a configuration report and get the ip address. If I type that in a webrowser, I get an error: unable to connect. Even if I plug the printer into the computer by a usb, I am unable to access the printer's ip address in the webrowser. I'm not sure how to proceed on getting the printer working wirelessly. It is a hp 6940 I use the HP Deskjet 6940 Series hpijs, 3.10.2rc1.9 driver. I have only recently been having printer problems. The printer has been hooked up on the same network for years. It still prints via usb.
I've run into a slight problem. As you can tell, I cannot connect to my HP printer through bluetooth. I've followed the Ubuntu documentation: [URL]... but I get stuck at actually connecting to the device. Here's the terminal output:
robertneville777@robertneville777:~$ hcitool scan Scanning ... 00:17:D5:06:3D:8CSAMSUNG SGH-T509 00:1A:0E:C3:F7:29Photosmart C5500 series
I give up.. after an hour trying to get my HP 7600 to network connect
My main box is usb connected to my HP Photosmart 7600 and works fine, my daughter has her winxp box connected to it over network as well. My wife's Ubuntu box (same OS and version as mine 9.10) CANNOT connect in any way, shape or form. I've tried every protocal, port, helper program (hp-setup, cups local webpage etc..) and nothing. I have the printer shared.
why connecting to a network printer in the same OS and version would take so much work?
Also we're all on the same network, & subnet with no filtering or firewalling in between the boxes.
*resolved* After trying everything else I restarted cups on the box the printer is attached and everything mysteriously works.
Have split hard drive into Windows 7 OS & Ubuntu OS. The printer connected to Windows 7 with no problems but I am unable to load the printer in Ubuntu 11.04.
I've bought a HP Photosmart printer, HP Photosmart wireless e-All-in-One printer - B110a and i've got a problem installing it properly. I'm using Debian 6.0 Squeeze. When i connect the printer, Debian doesn't recognize my printer as the Photosmart B109 printer for unknown reason. When i go to the site of HP and search for a driver, it directs me to this site:I've downloaded that latest hplip file as a .run file and installed it. My printer is recognized proparly, but when i try to print a colored image, it comes out black/white. Something is not crrect. Does anyone recognize this problem with this type HP printer?
I need to direction here: my laptop (F10 gnome) is cat5 dhcp connected to a dlink 524 router with IP 192.168.150.1. This in turn is connected to an arris modem with ip 216... Local IP is 192.168.100.1 (default). It works, connects to internet, supplies dhcp address to dlink. All this is upstairs in my ham room upstairs. My wifes laptop downstairs usually connects wirelessly to the dlink, and hence to the arris. Also works to the internet. There is a linksys (ddwrt software) running as a wireless repeater also located downstair, with box ip 192.168.1.1.
It is "joined" to the dlink router via wireless, hence it function, wireless repeater. It works, I have used it like this many time. However, I cannot seem to get a connection to the Brother printer (which has a print server function). It is connected to the linksys repeater via a lan cable. Gets an ip via dhcp. I think it should work, since my wife can connect to the linksys repeater, either wireless or wired, and surf the internet thru the dlink router via the repeater-dlink wireless repeater link. I must be missing something obscure (to me, at least).
I have shared my cpl-300 from my windows 7 machine to my network, so that may print from my linux laptop to it.
Now whenever I go to system -> Administration -> Printing and try and browse for my printer it asks for a username and password any username or password I enter that is on the windows 7 machine gets rejected.
So I tested to see what would happen if you used smbclient to view the shares available from the windows 7 machine, unfortunately it results in another permission error. The funny thing is I can mount a share using "mount -t cifs".
i would like to print to my home printer via the internet. printer is connected to the router directly by ethernet and i have a static ip address. i also have a static ip for the printer on the home network. how to set my netbook up to connect to the printer via the web with the info i have printer is a hp photosmart c5180 and afaik it is capable of using ipp. how do you route to the printers ip.
I can't connect a printer to my machine that's running Ubuntu 10.04 because it's outdated; however, I have another computer (Mac) that has a printer attached to it. Does anyone know how I can connect to that computer form my Ubuntu machine and send over documents to be printed on my Mac? Maybe through a remote desktop? Or SSL?
Printer directly connected with opensuse 11.2. we cant able to add printer in windows xp if wee add the system says the following error:
Function address 0x2c7d5e4 caused a protection fault. (exception code 0x0000005) The application property sheet page(s) may not function properly. And the system says acces denied unable to connect and the windows system hanging and says error report.
I am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
I just switched from Ubuntu to Fedora 13 because I was unable to get Ubuntu to connect to wireless networks. I tried everything suggested in help and forums, and kept getting "Bad Password" with WICD and Network Manager. Now, with Fedora...I still can't connect.
Problem #1: The guide says to "...make sure that the relevant wireless interface (usually eth0 or eth1) is controlled by NetworkManager," and that I do this via: System>Administration>Network
However, there is no Network option under System>Administration.
Problem #2: I open Network Manager, which displays a list of networks. I click on mine, configure it with WPA and the right password, and it fails to connect: "The network connection has been disconnected."
There is a printer connected to my Ubuntu box that I would like to share with XP users on my home network. When I browse for a network printer in XP the Ubuntu box is displayed, but does not display the connected printer.I added the following lines to cupsd.conf:Port 631Listen /var/run/cups/cups.sockand then restarted cups with:sudo /etc/init.d/cups restartI have also set ufw to allow incoming traffic through port 631 from each XP machine.
I can print very well over a USB cable, however I'm having trouble printing over the Internet (F13). The errors that I get are:
job-printer-state-message Unable to get printer status (Not Implemented!) job-printer-state-reasons [u'none']
Printer status usually shows up as OK until I actually start to print and then I end up with an error message and nothing prints. This seems to show up with any type of printer connected to the internet.
I am unable to add my USB printer via the YaST2 Printer Configuration setup tool in openSUSE 11.3. The printer, a Dell Color Laser 1320c, was last used with openSUSE 11.2, and setup was entirely uneventful. No driver is provided by Dell, so I used the Fuji Xerox DocuPrint C525A Linux driver. The problem: To add a print queue in 11.3, a Connection must be specified (parallel, USB, network, etc). However, the configuration wizard fails to show the presence of the USB print device.
[Code]...
This printer was working just eight weeks ago under 11.2, and 11.3 is obviously able to detect its presence and identify it correctly. I feel certain the solution is simple, but I haven't found documentation that provides the answer.
I was having no problems (that I knew of) browsing the web since installing Ubuntu 10.10 a week or so ago. I was previously trialling Win7 as my customers will likely be using that in the future. Then I wanted to go to internode.on.net. Got the following: Quote: Firefox can't establish a connection to the server at internode.on.net. or Quote: Oops! Google Chrome could not connect to internode.on.net
As it was just after Christmas I thought it must be down, for upgrades or maintenance etc. I later tried to go to Freebsd.org; same error. I've been having a small number of other websites give the same error. I thought nothing of this until I tried it on my wife's macpro. I could log onto all the websites I wanted to and none gave any indication of having been down. Both boxes are on the same adsl connection. I still can't access internode or freebsd on 10.10 yet have been able to access every website on OSX. Now, I was only looking at them for info but am worried I won't be able to access something important. (so far everything I 'need' is working)
ping just drops out. edit: weirdest thing! I just retried and now can not emulate the problem for internode. freebsd still won't show. that is less than five minutes between problems and resolution! I hadn't even posted! But I still would like to have an idea of what is going on. Here is the ping error for freebsd: Quote:
I'm facing a problem with 'ssh'. In my lan environment i've configured a system with fc12 and one more system with fc9. When i'm trying to login through ssh from fc9 to fc12 it's working, but at the same time if i'm trying to login through ssh from fc12 to fc9 it's not working. I was getting the error "connection closed by remote host"can any one suggest me how to recover this.
I'm trying to connect via ssh from a remote to a local machine.The local machine is connect to the ISP thru a wireless router. I know the ip address of the local machine from myaddress.com. The local machine is running sshd. I can ssh from the local machine to the remote, but I'm unable to ssh from the remote to the local. I know the local machine has not yet changed its port number.
I have Karmic Koala and together with my neighbours we have a W-LAN which I was always using without problems. Now, a couple of weeks ago, my neighbour has changed the password to this W-LAN and since then ubuntu is unable to connect. The network is being recognized, but after the request to unlock a key for the network manager (besides, how can I unlock it once for all?) there comes the window with the request for the network-password, after typing it (correctly), nothing happens. The request for the password comes two more times and then ubuntu states that it is unable to connect.
- We have changed the password again - didn't help - On Windows I and my neighbours get the connection - My Ubuntu is able to connect to all other W-LANs
I have an Ubuntu server dedicated to running an openVPN server on my VMware ESX 4 host. On my Windows clients I am able to connect to the VPN; however, on my Ubuntu 10.10 workstation I am unable to connect. Here is what I have done. I have network-manager-openvpn and dependices installed as well as the openvpn package. When I hit the add button in the network manager for VPNs, I fill out all the needed information, but am unable to hi the apply button. I have also tried using the openVPN method for connecting. I download the client.ovpn file from the VPN server, and issue the following command:
Code:
openvpn --config client.ovpn
It asks me for the authentication user and its password and produces this:
Code:
Mon Nov 15 21:37:20 2010 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Mon Nov 15 21:37:20 2010 Control Channel Authentication: tls-auth using INLINE static key file Mon Nov 15 21:37:20 2010 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication
I have been using Windows XP, and last month i had Linux Mint installed. I was connecting to the internet with an external modem and everything was running fine, until while experimenting with the settings,i bust the whole thing. What i did was to do a "right click" on the 'computer icon' at the bottom right-hand corner to disconnect and from that day i am unable to connect from Linux, but i can still do it under Windows.I had done the same thing under Windows but after going to the 'control panel/network settings' i managed to get the thing working.I went to the 'control panel' in Linux, and under 'network ' i get the message: "Auto eth0 => never". i have been trying to 'edit' the 'settings'
Just throwing in a quick question to see if anyone got any ideas about this.I'm unable to create a remote X session with TightVNC viewer. The local computer is a windows XP box and the remote server is running Slackware 13.
Using Putty on the XP box to connect to Xvnc through a ssh tunnel works just fine. However, when I fire up TightVNC viewer and try to connect to 127.0.0.1 as I'm used to, TightVNC viewer is unable to establish a connection to X. I'm puzzled.
This has worked when I used another XP box as local computer. I'm running all within my LAN. Can this be a firewall/iptables issue? I've obviously posted this in wrong forum category. Sorry about that. Starts this thread in server category too.
I have installed Fedora 10 on my Intel system. I am not able to connect to internet from it. Mine is a broadband connection with ADSL+2 modem. I could connect once but afterwards it was deactivated and I got following bug report.
Component: system-config-network Version: 1.5.93 Summary: TBd036c2a6 re.py:237:_compile:TypeError: first argument must be string or compiled pattern Traceback (most recent call last): File "/usr/share/system-config-network/netconfpkg/gui/tonline.py", line 79, in on_generic_entry_insert_text if re.match(str, text): File "/usr/lib/python2.5/re.py", line 137, in match [Code]...
