i can ping to 192.168.10.104 but can't access it graphically.i am using firefox.. distro is ubuntu.. i do //192.168.10.104:9345..but it takes no response.can u help me.. i am using direct connection..
View 6 RepliesI did everything and restarted my machine, everything seems to be ok. But when i type in my IP on the browser which is 10.0.11.25 which would be the localhost machine, i get this below:
Code:
ERROR The requested URL could not be retrieved
While trying to retrieve the URL: [URL] The following error was encountered:
* Connection to 10.0.11.25 Failed
The system returned:
(113) No route to host
The remote host or network may be down. Please try the request again.
I am using an virtual machine. where I need to ping from one machine to another. earlier I was able to ping. But after going to google.com once, I cannot ping back to this machine.
But if I gave ping -I eth1 <IP> then I can ping.
I cannot install any package, so tell me solution which includes not installing any package.
I just want to know how can I access root graphically if I want to paste a folder or write something then I have to do it by terminal I want to do it as graphically. If I am not wrong some thing like this system I found on fedora 8 but I want to do it in fedora 14. even f14 gedit not working.
View 6 Replies View RelatedI set up an apache webserver on a redhat enterprise server 6 last week. It works fine on the localhost. However, the webpage can't be accessed from the other computer. I didn't modify anything related to 'allow,deny' in httpd.conf. The only thing I've done is I added a rule in iptables to approve the access from a computer with a specific IP address. Since I am quite new to iptables, I don't know if there is anything wrong with my setting.
Even I stop iptables, the problem is still there. I don't know if my setting of iptables is correct. Or, there is anything else that I should do?
can't access website gives error 2082 2095
View 1 Replies View RelatedI have a Compaq Presario R3000 with Ubuntu 9.10 32 bit that I just installed last night. I'm using a Zyxel G-102 Wireless card and Actiontec GT701WG wireless modem.
When I try to connect to the 'net, the network does show up and it connects strong (100%). It also shows multiple neighbors networks. It pings at 99% success (with over 900 sent as I write this) but when I open Firefox it can't connect, it just times out. I've used WEP security and have switched off security as well. I tried hooking up to the modem via USB and get the same result. It acts like a Firewall issue but there isn't one installed - at least that I can find and the Firewall in the modem is off. I ran FF in root with gksu firefox as suggested in another thread. I tried www.ubuntu.com and the header loaded but that was all. Then it timed out.
I'm new to Linux but have used Puppy Linux with this machine and card, etc. so I know it can/does work with Linux. I wanted a more refined distro and chose Ubuntu.
Trying to access 67.15.245.6 (its a forum site). I can't get to it from home for over a month now. I can't ping it, but I can ping obvious things like google. Tracert isn't working at all. Once it hits the lightspeed.frokca.sbcglobal.net hop it just dies like ATT isn't allowing traceroutes. I've been using Tor as a work around. About 3 months ago I basically had the same issue with openbittorrent.com's site.
I have a linux server and windows XP box. I can't ping the above IP nor tracepath/traceroute to the IP from my linux box.
I have ATT uverse.
EDIT: The site is hometheaterlounge.com (The IP won't do you much and its just the IP of the site host).
I just downloaded and installed the latest Cent OS 5. I disabled SE linux, turned off the firewall, and selected the Server package options when installing. I plan on using this as a router/firewall between my internal network and the internet, as well as web server, etc. The first thing I did was to configure the two NICs, internal one with 192.168.7.1 address and the other with an address from my ISP (I have a static address, but I also tried to let the DSL router assign an address via DHCP). Everything looked fine, I checked /etc/resolv.conf and my routes. I was able to ping the DSL router from the server, but I was not able to do a ping or lookup on anything outside my network. I tried host, dig, nslookup, etc, no luck. Obviously then, I was not able to browse the net with firefox.
View 4 Replies View Relatedi have a website named [URL]... now i want to access this website using proxy server(squid,or etc...) under my personal server named [URL]...means that [URL]...
View 4 Replies View RelatedBasically, I have a windows 2003 server virtual machine (vmware) inside Ubuntu 9.10.
The Ubuntu machine has IFconfig:
Code: sam@sam-laptop:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:15:c5:b8:c8:8b
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:17
Why can't I ping or simply access the internal server on my ubuntu machine from a another computer on the 192.168.1.0 (slash)25 physical network? Do I need a bridge? Iptables?
Presently this client access the net through following setup
ADSL modem -> hub -> all computers
Now they want to do some kind of bandwidth control, content filtering. So I tried setting up squid with dansguardian. This is what I did
ADSL -> linux server -> all computers.
The linux server has two NIC cards. One to the ADSL router and another to the local hub. This is how my squid.conf file looks like
http_port 3128
acl ubc src 192.168.1.0/255.255.255.0 (for subnet)
http_access allow ubc
Have set the gateway server as 121.x.x.1. Which is the gateway server of the ISP. Now I can ping the local network, but cant ping the gateway or any other website. Also I am unable to access the router administration page.
Im running drupal on my webserver and, this morning all of the sudden I went to edit a node and now I cant load the website in my browser at all. I can ping the machine and SSH into it fine, but it will not load the website in chrome or IE, I have no idea whats going on here.
Edit: I did a 'service httpd restart', it took 3mins to restart, is this normal? After I did that it loaded once, not even all of the page, now its doing the same thing again.
Edit2: Now it seems to be working fine again...
When I try to ping with the terminal to check a website's availability, it always just keeps going on and on and on... How do I get it to stop after a set amount of pings? Is there some type of command?
View 6 Replies View RelatedI am trying to install a router on my CentOS 5 box, while i have properly configured IP address, Subnet, Default GW and DNS, I am at the point of trying to set up the Proxy. I have added a line: "proxy=http:ip_address:8080/" to the file of "/etc/yum.conf" The Proxy server here does not require any username nor password however I still cannot ping any website, while I tried to ping 74.125.45.100 (google.com) it returns the following message:
[Code]....
I have 4 centos5 apache webservers all on the same network, recently, 2 of the webservers have stopped being able to ping or browse one particular website where feeds are obtained from this site. I have checked and firewall and selinux settings are disabled. The two webservers are able to ping and browse other sites. Dns settings are the same for all 4 servers. traceroute for working and not working webservers are the same.
View 1 Replies View Relatedwe are trying to install this NIC Rosewill RC-400 Chipset RTL8169S-32 in Ubuntu 9.04 we downloaded the drivers from Rosewill website (For kernel 2.4.x and 2.6.x V 3.1) but when we follow the instruction in the readme file and do make clean modules and error comes out
Code:
make -C src/ clean
make[1]: Entering directory `/home/trinity/Desktop/r8169-6.006.00/src'
rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions Module.symvers Modules.symvers rset[code]...
So I went do realteak downloaded latest available drivers that seems to be were release yesterday did same command and same error So I made only make and it went fine did then make clean modules and went fine so made make install, depmod -a and modprobe r8169 verify int was up and getting correct ip from router but I'm not able to access the internet or ping any IP address
Code:
xxx@xxx-desktop:~$ uname -a
Linux xxx-desktop 2.6.28-18-generic #60-Ubuntu SMP Fri Mar 12 04:40:52 UTC 2010 i686 GNU/Linux
xxx@xxx-desktop:~$
There is a test/development environment here at work with some windows and some CentOS systems connecting over a network share to a CentOS fileserver in the data center. The developers run as root (i know i know, but the environment is completely cut off from the rest of the company and this just worked best) and connect to the fileserver using samba. I tried using nfs but to no avail. Now, a couple of the developers have no issues with permissions at all but a couple of them are not able to delete files or folders in their network share graphically. They can through terminal though.
View 4 Replies View RelatedI would like to know how to monitor dual nic cards graphically in real time. I want to be able to see the traffic of each port separately.
View 3 Replies View RelatedIve got a problem on my server ....installed Debian 5 , Webmin and than syscp settung up syscp ready ....
I try to ping "localhost" ansver ping: unknown host
I try to ping "localhost." there is a host with IP 127.0.0.1
I need it to change it in "localhost"
Is that the bind9 maybe?
I have two machines on this network, one running Ubuntu and the other running Fedora.
When I'm using the Wireless network on the Ubuntu machine, I cannot ping the Fedora machine. Everything else works. I can browse the net fine.
If I switch over to the Wired Network then I can ping the other machine.
I don't understand why ping doesn't work only over the Wireless. I can ping the router so I'm guessing it's getting blocked by the router but I didn't block ICMP traffic.
I tried asking on IRC and they ran out of ideas too to find out where the problem is.
I just installed my first EVER bind DNS server. I am running bind9 on Ubuntu 10.04. Everything seems to be working great except one thing: If I ping a host that I have set up in bind by its HOSTNAME the pings take 5-6 seconds to reply/print to the screen between each echo response. If I ping by the host's IP address, they echo back very quickly.
I have read that IPv6 can cause this, but I have disabled it in /etc/sysctl.conf and the problem still exists.
I know everyone says this can't be a DNS issue, but this never was an issue with dnsmasq (which i was using prior), and it doesn't make sense that the ping are ONLY slow when pinging by hostname and not IP.
Configs below:
Ping by hostname - there is a 5-6 second delay between each one of the responses:
Code:
Ping by IP - the responses come VERY quickly one after the other:
Code:
/etc/resolv.conf:
Code:
Code:
rev.0.168.192.in-addr.arpa:
Code:
So, I have an Virtual Machine running CentOS 5.4. It sits behind a hardware firewall which also does NAT'ing. I've set up plenty of these, so I know for sure the firewall and NAT rules are set up correctly. From the host, I can ping anything in my subnet and the gateway. But I can't ping anything else beyond the gateway. I can perform DNS queries and when I try to ping, it finds the appropriate IP address.But from the outside, I can ping the PUBLIC address (It's a 1 public to 1 private address NAT, not 1 public to multiple private). I've tried it with IPTABLES on and off, with no change.
View 11 Replies View RelatedI have Mandriva One 2009.0 (192.168.1.100) on one box and Mandriva Free 2010.0 (192.168.1.118) on the other. I can ping router (192.168.1.1) from both of these boxes but I can't ping one box to the other and the other way around. What's going on?.
Do I have to change some settings in router?. Or is it firewall issue on those two machines?. Both of these boxes are connected by cable. Symbol of the router: TL-WR340G.
I have connected xp and fedora through crossover cable . xp has ip address 192.168.0.1/24 (manually assigned) fedora has 192.168.0.2/24 with default route equal to 192.168.0.1
I can ping fedora from xp computer but i can't able to ping xp from fedora computer.
I have manully edit the /etc/sysconfig/network-scripts/ifcfg-eth0 file with correct subnet mask and ip address because when i tried to give ip address manully in network manager the subnetmask is replaced with gateway address don't know why.
Now i want to share internet through crossover cable . xp is connected to internet through wireless usb adapeter.
Using Fedora 13,The Website shows well in Local host, but no able to access it from any other host.I get the error message " The server at xxx.xxx.xxx.xxx is taking too long to respond".
View 13 Replies View Relatedi'm using fedora 9 and mozilla 3 with dsl internet connection. i can't access some site in my computer but other computers can using internet explorer. i hope this is the right forum for this.
View 8 Replies View RelatedI have a strange problem with sites on which there are many images, the likes of ebay or the google image search. The images or the preview images won't load in Ubuntu (I am on 9.10).
Neither using FF, Konqueror nor Chrome.... It can't be the router either, because when I boot into Windows on the same machine it is working.
It is even working on a MAC at the same it doesn't work on Ubuntu....
Our setup is 64bit F13, Firefox/NoScript, KDE, when trying to access www.nook.com we get a long pause followed by "server not found" message. We can change to another hard drive and boot WinXP/Firefox/NoScript and we a get a redirect to:http://www.barnesandnoble.com/nook/i...refront-_-nook
You can see thread about it here also:http://www.linuxquestions.org/questi...-linux-835160/
I just bought the Barnes & Noble Nook eReader for my wife's birthday and a requirement is to log on to the Nook website and establish an account. Using her Fedora 13 64bit desktop and Firefox she repeatedly tried to access the website www.nook.com to create an account, however consistently got the server not found message. Even using the Firefox addon User Agent Switcher and turning off NoScript did not correct this.
When we switched over to the WinXP install and Firefox we were able to access the website no problem. Anyone else unable to access that website via linux?