I am using an virtual machine. where I need to ping from one machine to another. earlier I was able to ping. But after going to google.com once, I cannot ping back to this machine.
But if I gave ping -I eth1 <IP> then I can ping.
I cannot install any package, so tell me solution which includes not installing any package.
Even ping google's ip address doesn't work. unknown host error using backtrack4 able to browse net with these settings.
My network settings:
What's the problem with these settings...
Ive got a problem on my server ....installed Debian 5 , Webmin and than syscp settung up syscp ready ....
I try to ping "localhost" ansver ping: unknown host
I try to ping "localhost." there is a host with IP 127.0.0.1
I need it to change it in "localhost"
Is that the bind9 maybe?
I have two machines on this network, one running Ubuntu and the other running Fedora.
When I'm using the Wireless network on the Ubuntu machine, I cannot ping the Fedora machine. Everything else works. I can browse the net fine.
If I switch over to the Wired Network then I can ping the other machine.
I don't understand why ping doesn't work only over the Wireless. I can ping the router so I'm guessing it's getting blocked by the router but I didn't block ICMP traffic.
I tried asking on IRC and they ran out of ideas too to find out where the problem is.
I just installed my first EVER bind DNS server. I am running bind9 on Ubuntu 10.04. Everything seems to be working great except one thing: If I ping a host that I have set up in bind by its HOSTNAME the pings take 5-6 seconds to reply/print to the screen between each echo response. If I ping by the host's IP address, they echo back very quickly.
I have read that IPv6 can cause this, but I have disabled it in /etc/sysctl.conf and the problem still exists.
I know everyone says this can't be a DNS issue, but this never was an issue with dnsmasq (which i was using prior), and it doesn't make sense that the ping are ONLY slow when pinging by hostname and not IP.
Configs below:
Ping by hostname - there is a 5-6 second delay between each one of the responses:
Code:
Ping by IP - the responses come VERY quickly one after the other:
Code:
/etc/resolv.conf:
Code:
Code:
rev.0.168.192.in-addr.arpa:
Code:
So, I have an Virtual Machine running CentOS 5.4. It sits behind a hardware firewall which also does NAT'ing. I've set up plenty of these, so I know for sure the firewall and NAT rules are set up correctly. From the host, I can ping anything in my subnet and the gateway. But I can't ping anything else beyond the gateway. I can perform DNS queries and when I try to ping, it finds the appropriate IP address.But from the outside, I can ping the PUBLIC address (It's a 1 public to 1 private address NAT, not 1 public to multiple private). I've tried it with IPTABLES on and off, with no change.
View 11 Replies View RelatedI have Mandriva One 2009.0 (192.168.1.100) on one box and Mandriva Free 2010.0 (192.168.1.118) on the other. I can ping router (192.168.1.1) from both of these boxes but I can't ping one box to the other and the other way around. What's going on?.
Do I have to change some settings in router?. Or is it firewall issue on those two machines?. Both of these boxes are connected by cable. Symbol of the router: TL-WR340G.
This applies to my 2 opensuse PC's, my Windows PC is fine.I can ping a hostname, say "PC1" but I can not ping PC1.domain.local (even the host PC can not ping it's own FQDN). When I ping just the hostname the ping stats even list the FQDN.Onto the next issue, since all my PC's, have the domain prefix domain.local, my Synology can not. I can ping it's IP and that is it. I can resolve it's name with nmblookup just fine tho and that is what is killing me. How is this not resolving.Even weirder, I can browse to "Synology" in Network Servers under places on the slab.
View 3 Replies View RelatedI try to use the "ping -a" command for getting an audible ping. But there is just silence The command "beep" works fine, so everything should be ok with the speaker (in the konsole).
View 3 Replies View RelatedI have connected xp and fedora through crossover cable . xp has ip address 192.168.0.1/24 (manually assigned) fedora has 192.168.0.2/24 with default route equal to 192.168.0.1
I can ping fedora from xp computer but i can't able to ping xp from fedora computer.
I have manully edit the /etc/sysconfig/network-scripts/ifcfg-eth0 file with correct subnet mask and ip address because when i tried to give ip address manully in network manager the subnetmask is replaced with gateway address don't know why.
Now i want to share internet through crossover cable . xp is connected to internet through wireless usb adapeter.
I have a debian server installed with a static ip. Now i am able to ping my ip, but when i try to configure a domain name with the nameserver as my ip, i am not able to ping the domain name
eg:
When i ping www.google.es, i get something like:Quote:
ping www.google.es
(wait 20 seconds)
64 bytes from 66.249.92.104: icmp_seq=2 ttl:53 time=80 ms
[code].....
I try to ping with php : exec("ping -n 1 $ip",$output[],$retval); it works fine in window. but in linux i got this error : ping: icmp open socket: Operation not permitted are there any ways to solve this ?
View 5 Replies View RelatedHost - Fedora 12 64bit
KVM
VM - Windows Server 2008 64 bit
bridge-utils
VM can ping host and Internet but host can't ping VM.
I set VM static IP 192.168.0.205.
It turns out dynamic IP - 192.168.0.55
On host:
I am not able to move original thread so I am linking to it: [URL]
View 2 Replies View RelatedSomething strange with my firewall i used firestarter I dont know why i cannot ping outside on a specific IP address here is my setup. I have IP from ISP
119.92.56.77 - eth0
192.168.50.1 - eth1
with DHCP features from 192.168.50.1 - 254. my problem is i cannot ping this specific IP address which is 119.93.232.234 if you can try there and pinging is ok but here cannot because that IP address (119.93.232.234) they used that to connect to our openvpn which is the IP is 119.92.56.78 <---- this system linux(centos) or IP has no firewall enabled. meaning i separeted this connection. which my setup is like this for OPenVPN
[code]...
I have a linux machine with 2 ethernet ports(eth0 and eth1). eth0 is connected to a router which assigns it an IP address 192.168.1.2. eth1 is connected to a switch and I assigned it an IP address 192.168.1.254 using "ifconfig eth1 192.168.1.254 netmask 255.255.255.0 up". How do I ping eth0 from eth1?
View 5 Replies View Relatedmy network expertise is tenuous at best. This started because one computer on my network is having trouble updating Google Toolbar information. This is a laptop which joins other wifi networks outside of the house.
Code:
BROKEN:~$ ping toolbar.google.com
PING toolbar.google.com (208.68.139.89) 56(84) bytes of data.
[code]....
I have installed openvpn on an ubuntu 10.04 server. I run 11.04 on my desktop. It can connect to my VPN server. The problem is, I have ZERO internet access. I cannot even ping an IP address.
View 5 Replies View RelatedI have a server with centos 5 and plesk 9 and I have buy an additional IP address for my server, when i create it in plesk, there is no problem, all its ok I can assign it to a new domain, but the ip only responds ping, none of other services as http, ssh or smtp.I paste here the configuration of files
ifcfg-eth0
device=eth0
bootproto=dhcp
[code]....
Since two days i m not able to browse websites using the domain names but able to ping/browse using IP addressed. I have done the following:
1. Using wireless i m able to get IP address of DNS (8.8.8., Gateway, localhost & router ip address
2. Disabled wireless and connected ETH0 but still the same problem
3. not able to edit resolv.conf
sudo gedit resolv.conf
** (gedit:4179): WARNING **: Hit unhandled case 0 (Error opening file: Input/output error) in parse_error.
[code].....
I run an centos server. From the console I can ping google.com and get a reply. But when I ping another address say xyz.com, the IP address is resolved (11.22.33.44) but there is no reply. In the same network in our office from my desktop I ping [URL] and there is a reply.I turned of the firewall but still the same problem.
View 9 Replies View RelatedA brief description of my network:It is a small home network consisting of an Ubuntu 10.04LTS server edition, an Iomega ix2 NAS, a WinXP pro server and several family laptops.This is all routed through a Netgear WNDR3300 home router. All are assigned IP's via DHCP and all but the laptops are static (via DHCP though). The WAN address/DNS is assigned via DHCP from my ISP.The problem:When one of the machines is offline, Ubuntu does not resolve the netbios name correctly. No surprise here. But what is happening is that it is finding some arbitrary machine on another network. Below is what a ping to an offline host reveals:
Code:
ping -c3 hostname
PING hostname (204.232.162.92) 56(84) bytes of data.
[code]....
I've only been using linux for a few days so I don't know all the tricks. I'm pretty savy configuring windows networks however.My adapter is (according to windows) a: CNet PRO200WL PCI fast ethernet adapterLinux says it is a: 21x4x DEC-tulip compatible 10/100 EthernetI do seem to be getting an ip address from the DHCP router, but I cannout ping any other ips or connect to the internet.I've tried a bunch of different options, switching things back and forth, but it still doesn't work, and honestly i don't even know what some of the options mean.
ALSO, if this helps:
paladin:~ # ifconfig eth0
Eth0 Link encap:Ethernet HWaddr 00:08:A1:03:3C:99
[code]....
I installed nss-mdns in Fedora Core 10 and can see all the Bonjour published hosts on the lan. However, I am always forced to append the .local domain when referring to a host:
Code:
% ping foo.local
works
[code]....
I am working behind a http proxy (172.30.x.x:3128). I have configured it in my terminal. All the applications such as wget,lynx firefox etc. are working correctly.However all dns utilities like nslookup, host and even ping too are not working.Following is output of host command:
Code:
root@ding:~# host google.com
;; connection timed out; no servers could be reached
Output of host -T:
[Code]....
To connect to net I have to first run dhclient3(learnt from this forum!).It gives me my ip but where is dns address sent I don't have and idea.
When I execute a command (ping or telnet or ssh) on ip 192.168.0.20 it is ok.
If I execute the same command on
ip 192.168.0.020, it looks for
ip 192.168.0.18 instead of
ip 192.168.0.20
And it's the same for others ip if I put a 0 ahead last byte.
If I type
Code:
$ ping [URL]
or even
Code:
$ ping google.com
should I receive a reply?
I have 2 windows PC and a linux as router in the linux there are 2 NIC eth0 and eth1. I created DHCP on eth0 and manually configured on eth1. My eth0 gateway was 192.168.26.253 and my eth1 was 192.168.22.253. I needed to ping the 192.168.26.x WinPC1 to WinPC2. What command I will use on linux so that the WinPC1 can ping to WinPC2.
View 6 Replies View Relatedwe are trying to install this NIC Rosewill RC-400 Chipset RTL8169S-32 in Ubuntu 9.04 we downloaded the drivers from Rosewill website (For kernel 2.4.x and 2.6.x V 3.1) but when we follow the instruction in the readme file and do make clean modules and error comes out
Code:
make -C src/ clean
make[1]: Entering directory `/home/trinity/Desktop/r8169-6.006.00/src'
rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions Module.symvers Modules.symvers rset[code]...
So I went do realteak downloaded latest available drivers that seems to be were release yesterday did same command and same error So I made only make and it went fine did then make clean modules and went fine so made make install, depmod -a and modprobe r8169 verify int was up and getting correct ip from router but I'm not able to access the internet or ping any IP address
Code:
xxx@xxx-desktop:~$ uname -a
Linux xxx-desktop 2.6.28-18-generic #60-Ubuntu SMP Fri Mar 12 04:40:52 UTC 2010 i686 GNU/Linux
xxx@xxx-desktop:~$