I have eth1 and eth2 connected with back to back cable on the same machine.
I configure eth1 with 11.11.11.11 and eth2 with 11.11.11.14.
I use ping -I eth1 11.11.11.14, I get Destination Host Unreachable...
using tcpdump on eth1 shows ARP request broadcast being sent out
using tcpdump on eth2 shows ARP request received, no ARP reply being sent out
Not sure whether this config is supposed to work?
I have an ubuntu kk laptop connected via wireless to my mixed network (xp, win7, other ubuntu), but i can not ping said machine or connect via ssh. Internet and smb-browsing ON this machine work, as does pinging FROM it. If this was a windows machine, I'd say a firewall is in the way, but since it's a vanilla karmic install, this should not be the case (or should it?).
View 2 Replies View RelatedI have two machines, one has XP service pack2, second one has CentOS 5.3 (Linux), they are connected through crossover cable. I have configured everything fine but don't know why till now can't ping!
A. Windows machine settings as follows:
IP Address: 192.168.1.3
Subnet Mask: 255.255.255.0
Default Gatway: 192.168.1.1
+ Firewall is turned OFF.
B. For Linux machine, I will list everything stored in network files, logged as [root@localhost ~]# :
1. /etc/sysconfig/network:
ifconfig eth0 192.168.1.4 netmask 255.255.255.0 up
route add -net 192.168.1.0 netmask 255.255.255.0 eth0
route add default gw 192.168.1.1 eth0
NETWORKING = yes
NETWORKING_IPV6=no
HOSTNAME=localhost.localdomain
2. /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE="eth0"
IPADDR="192.168.1.4"
NETMASK="255.255.255.0"
ONBOOT="yes"
BOOTPROTO="yes"
3. /etc/resolv.conf
nameserver 192.168.1.4
search locadomain
4. I restarted network service using this command:
/etc/init.d/network start
everything is fine. When checking using ifconfig command. I get the following:
eth0 Link encap: Ethernet HWaddr 00:08:0D:EE:19:66
inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr:........
[code]....
I mean I assigned the IP: 192.168.1.4 to Linux machine (Eth0). I did everything above and can't ping till now, when pinging from windows or Linux I get a message "destination host unreachable" restarted Linux many times but same result. NETWORK CABLE is working fine I tested it.
I have a bit of a strange scenario. I have a machine with a fixed IP (192.168.0.108), running Linux. It has an external IP 99.99.99.8 via a 1:1 NAT on a Cisco ASA/router. Port 3389 (MS RDP) is open for 99.99.99.8. I want my Linux machine to listen on port 3389 and redirect all traffic to that port to a Windows machine (192.168.0.100). In this way, my Linux box is able to respond to requests on all ports, but port 99.99.99.8:3389 connects to Remote desktop on the Windows PC. I do not have access to the Cisco NAT config. I was able to get this setup to work by using an SSH tunnel.
I ran this command on the linux box:
ssh -L 3389:192.168.0.100:3389 ergosteur@192.168.0.108
Any ideas? Perhaps using iptables or something?
I am using f13
Quote:
$ uname -rsmi
Linux 2.6.33.8-149.fc13.i686.PAE i686 i386
I am using a dhcp network. Problem is I can SSH/ping to my machine but can't SSH/ping to my machine from the remote one(In internal network of my lab). What to do? I understand this is very little information....but I dont know what to provide.
Have installed fedora 14 on a HyperV virtual machine, have added a Legacy network adapter in the Hyper-V settings for this virtual machine that fedore pics up as eth0. I'm pretty sure this card is able to pick up an IP address from a DHCP server on our network but I'm unable to ping any boxes from this fedora virtual machine or ping the fedora machine from another box on the network. I have tried to disable the firewall and SELinux incase it was that stopping the pinging each way but that didn't help.
View 1 Replies View RelatedI installed apache2 on my Ubuntu machine and I am trying to access the server from another subnet. The server is connected using ethernet and has a static ip address. I can ping from the server to any machine in the other subnet but non of the machine on that subnet can ping the server. iptables does not seem to be running
Code:
# service iptables status
iptables: unrecognized service
and its rules are
Code:
# iptables -L
Chain INPUT (policy ACCEPT)
target prot opt source destination
Chain FORWARD (policy ACCEPT)
target prot opt source destination
[code]....
What is preventing my machine from being accessed from the other subnet?
I am running ubuntu 10.04 on a VMWare Server virtual machine. I have assigned the ubuntu machine an ip address of 192.168.17.101. The ip address of my Windows machine hosting the Ubuntu VM is 192.168.17.100.
From the Ubuntu machine, I can ping all other machines on the local subnet. But when I try to ping the ubuntu machine, it does not get a reply.
I have a clean, plain install and the only software I have installed is Nagios.
This is the scenario: gentoo box (distro shouldn't be relevant here) and win7 box. Gentoo box is dhcp and dns server, via dnsmasq. From win7, I can ping gentoo by both ip and name. No problem there. From Gentoo, I can ping win7 by ip, but not by name. The dnsmasq log seems to receive the name ok, it's "Tere-PC". I have been looking around for many hours now and I know there must be something simple I am not taking into account.
Code:
dnsmasq-dhcp: 55480937 available DHCP range: 192.168.0.50 -- 192.168.0.150
dnsmasq-dhcp: 55480937 client provides name: Tere-PC
dnsmasq-dhcp: 55480937 vendor class: MSFT 5.0 .....
Code:
# ping Tere-PC
ping: unknown host Tere-PC
Is there any way that dnsmasq, which is supposedly a dns server, will link this name to the given ip?
I've a weird problem about my honeypot project. All start from installation until running process is going smoothly but when I try to ping my honeyd vm from honeyd host it couldnt but it can be ping from other machine inside my local network. I am also usinng arpd for ARP request reply and standard honeyd config.
View 1 Replies View Relatedi have installed linux debian in my computer but i have aproblem , i have a ping only on my computer itself , not to gateway or other computers on my network .
Ip : 10.0.88.9
Gateway : 10.0.88.1
dns :10.0.88.7
note:when i have installed system i have no internet connection so it is not installed updates
I am using an virtual machine. where I need to ping from one machine to another. earlier I was able to ping. But after going to google.com once, I cannot ping back to this machine.
But if I gave ping -I eth1 <IP> then I can ping.
I cannot install any package, so tell me solution which includes not installing any package.
I have a linux machine with 2 ethernet ports(eth0 and eth1). eth0 is connected to a router which assigns it an IP address 192.168.1.2. eth1 is connected to a switch and I assigned it an IP address 192.168.1.254 using "ifconfig eth1 192.168.1.254 netmask 255.255.255.0 up". How do I ping eth0 from eth1?
View 5 Replies View RelatedI am trying to ping my Windows machine connected to an open network (I'm at a internet caf) from my linux VM (also connected to the same network with a usb adapter), but I'm obtaining this output:
# ping 10.23.47.12
PING 10.23.47.12 (10.23.47.12) 56(84) bytes of data.
From 10.128.128.1 icmp_seq=1 Packet filtered
From 10.128.128.1 icmp_seq=2 Packet filtered
With high probability host 10.128.128.1 is a firewall or some router with packet filtering mechanism; but I don't understand how it can be possible to implement this kind of solution, with what kind of software or hardware? I also tried a nmap scan to my Windows machine but it returns me scan results from another host(the firewall or the router I suppose):
nmap -sS -O -P0 10.23.47.12
Starting Nmap 5.51 ( http://nmap.org ) at 2011-07-09 15:46 CDT
Nmap scan report for 10.23.47.12
Host is up (0.097s latency).
All 1000 scanned ports on 10.23.47.12 are filtered
[Code]...
So my questions is, how is technically possible to implement this kind of restriction within hosts connected on the same network? It's the first time I see this kind of configuration.
I have Linux server with VMware Server 1.0.8. When I creating a virtual machine, I can not "send" a PING to the virtual machine. In the virtual machine, I have installed CentOS 5.3 (32bit). In the virtual machine I have defined the addresses IP. So, whey I can't "sent" a ping to the virtual machie? I have to set something on the Linux server?
View 3 Replies View RelatedIve got a problem on my server ....installed Debian 5 , Webmin and than syscp settung up syscp ready ....
I try to ping "localhost" ansver ping: unknown host
I try to ping "localhost." there is a host with IP 127.0.0.1
I need it to change it in "localhost"
Is that the bind9 maybe?
I have two machines on this network, one running Ubuntu and the other running Fedora.
When I'm using the Wireless network on the Ubuntu machine, I cannot ping the Fedora machine. Everything else works. I can browse the net fine.
If I switch over to the Wired Network then I can ping the other machine.
I don't understand why ping doesn't work only over the Wireless. I can ping the router so I'm guessing it's getting blocked by the router but I didn't block ICMP traffic.
I tried asking on IRC and they ran out of ideas too to find out where the problem is.
I just installed my first EVER bind DNS server. I am running bind9 on Ubuntu 10.04. Everything seems to be working great except one thing: If I ping a host that I have set up in bind by its HOSTNAME the pings take 5-6 seconds to reply/print to the screen between each echo response. If I ping by the host's IP address, they echo back very quickly.
I have read that IPv6 can cause this, but I have disabled it in /etc/sysctl.conf and the problem still exists.
I know everyone says this can't be a DNS issue, but this never was an issue with dnsmasq (which i was using prior), and it doesn't make sense that the ping are ONLY slow when pinging by hostname and not IP.
Configs below:
Ping by hostname - there is a 5-6 second delay between each one of the responses:
Code:
Ping by IP - the responses come VERY quickly one after the other:
Code:
/etc/resolv.conf:
Code:
Code:
rev.0.168.192.in-addr.arpa:
Code:
So, I have an Virtual Machine running CentOS 5.4. It sits behind a hardware firewall which also does NAT'ing. I've set up plenty of these, so I know for sure the firewall and NAT rules are set up correctly. From the host, I can ping anything in my subnet and the gateway. But I can't ping anything else beyond the gateway. I can perform DNS queries and when I try to ping, it finds the appropriate IP address.But from the outside, I can ping the PUBLIC address (It's a 1 public to 1 private address NAT, not 1 public to multiple private). I've tried it with IPTABLES on and off, with no change.
View 11 Replies View RelatedI have Mandriva One 2009.0 (192.168.1.100) on one box and Mandriva Free 2010.0 (192.168.1.118) on the other. I can ping router (192.168.1.1) from both of these boxes but I can't ping one box to the other and the other way around. What's going on?.
Do I have to change some settings in router?. Or is it firewall issue on those two machines?. Both of these boxes are connected by cable. Symbol of the router: TL-WR340G.
This morning I was looking at the router's log file and noticed a certain IP address was able to gain LAN access on port 2222. That just happens to be the port my SSH server is listening on! A whois search revealed that IP address is in Germany. As soon as I found this out I stopped forwarding all ports to this machine in my router.
how to tell what had happened, what information this person was able to obtain, and if he left any goodies behind that could hurt me? I've read through some of the logs on my computer and haven't been able to find much at all. I did have some personal information on the hard drives, but that information is encrypted. I'm thinking if they were able to get my SSH password then that information probably isn't safe either (assuming they have some of it).
i have two linux machines(machine1(rhel client) and machine2(rhel server)) i am able to login the machine2 from machine1 but i am unable to ping machine1 from machine2 fire wall is stoped in both machine
View 1 Replies View RelatedI'm trying to list all ports less then 1024 on my current machine which are open in the listening state, one port per line
View 1 Replies View RelatedI recently did a clean install of Debian 5, and a backup program called BackupPC. Both machines are on a small local network served by a router. Both machines have statically mapped IP addresses, done by the router via matching MAC addresses in a table of corresponding IP addresses (192.168.0.2 (HP-PC-XP), 192.168.0.3 (Debian). I configured Backup PC correctly (I think)...Upon running Backuppc, the first thing it tries to do when its time to run a backup is to ping the machine to be backed up. The name of the PC is stored in a backup pc config file. (I believe BackupPC does a DHCP request with the machine name to get the ip address, but not sure). Running the backup results in BackupPC tells me that it can't ping my xp machine. If I open up a terminal window in debian, i can successfully ping my xp machine when i use the ip address. 92.160.0.2 If I ping using the host name of the xp machine (e.g. HP-PC_XP), the ping command displays some ip address i've never seen...something like 63.123.155.104....how is it getting that and how can it be corrected?
I recall that nslookup looks at the local hosts file first to resolve the name....i look in my hosts file and found no such address (only contained localhost)....now what?
I am setting up Ubuntu to be a firewall type device for a windows computer. (I later want to use Internet sharing or something like that.) The Ubuntu machine has two NICs. The internet NIC works but one light is always orange (even when there is no patch cable connected to it). I can access the Internet fine from the Ubuntu machine. I have a cross over cable connected to the second NIC. This cable connects to the Windows laptop. The windows laptop can ping the Ubuntu machine. But I cannot ping the windows machine from the Ubuntu machine. When I try to telnet to the Ubuntu machine from the Windows machine (over port 23 or 80) it says "cannot connect."
From the Ubuntu machine I issued this command:
# iptables -A INPUT -p tcp --dport 80 -j ACCEPT
I used ufw status and found that the firewall was not enabled on the Ubuntu machine. The default gateway of the second NIC is the IP address of the Windows machine. The default gateway of the Windows machine is the IP address of the Ubuntu machine.
how a ubuntu machine can ping another (I can see the ICMP request and response in wireshark) but in the terminal I get 100 % packet lost ? Same with the DNS requests ( I see the query to the DNS and the DNS is giving me the IP of the site) and internet connections at all. this machine is sharing it's internet connection and machines behind it have no problem with the internet. I tried to flush the iptables - same result. This thing occurred after a restart
View 2 Replies View RelatedRunning Fedora 10, I installed CentOS 5 in Virtualbox, but I can't ping the Virtual Machine...
From within CentOS, I can ping my laptop [known as the host?] but from the laptop I can't ping the CentOS Virtual Machine. I tried turning off the firewall on both too... CentOS was able to access the internet through my laptop right away without any configurations too.
Unless someone has an idea to resolve the above, I am also wondering about something else VirtualBox-related:
To see if it was possible to get around the above issue, I was going to install another CentOS virtual machine to see if I can get them to communicate both ways [if at all], but to do so, I think I have to install CentOS AGAIN on another allocated amount of hard disk space. This will take some time, so I was wondering if anyone knew if it was possible to just create a quick duplicate of the previous installation, if you wanted 2 different virtual installations of the same OS.
I just configured vhost server in my linux server. When trying to access the open source (SugarCRM) application running on it, its giving me the error message that i am not connected to internet. I have restarted apache by no luck.
View 1 Replies View RelatedI have connected xp and fedora through crossover cable . xp has ip address 192.168.0.1/24 (manually assigned) fedora has 192.168.0.2/24 with default route equal to 192.168.0.1
I can ping fedora from xp computer but i can't able to ping xp from fedora computer.
I have manully edit the /etc/sysconfig/network-scripts/ifcfg-eth0 file with correct subnet mask and ip address because when i tried to give ip address manully in network manager the subnetmask is replaced with gateway address don't know why.
Now i want to share internet through crossover cable . xp is connected to internet through wireless usb adapeter.
I try to ping with php : exec("ping -n 1 $ip",$output[],$retval); it works fine in window. but in linux i got this error : ping: icmp open socket: Operation not permitted are there any ways to solve this ?
View 5 Replies View Related