I can't get my card Intel Wireless 5300 AGN to work. I'm running Slackware 13.1 and it's a full, fresh install.I get to show up with lspci -v:Network controller: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection...But it will not show up with 'ifconfig' which will only list the local loopback (yes we have have a eth problem as well but one thing at a time).
View 5 Replies
I have an intel 5300 wireless chipset which is not supported in kernel 2.6.25. I am currently using opensuse 11.0, I downgraded from 11.1 since I faced so many other problems. can I setup my wireless driver under kernel 2.6.25? if so, how could i do this?
View 7 Replies View RelatedThe wireless on my 64-bit openSUSE-11.2 installed on my Dell Studio 1537 laptop stopped working some time back (possibly more than a one or two months back). I just discovered this last week when on business. I have not used the wireless under openSUSE-11.2 for a while so I am not certain what broke it, but I am suspicious of an update. I note openSUSE-11.3 milestone-7 works great with the wireless (on a liveCD). I note possibly two related threads, although I note no failed request for firmware in my case:request for firmware file 'iwlwifi-5000-2.ucode' failed [INTEL 5300 AGN] [OPENSUSE 11.2] - openSUSE Forums, and I see another thread here: Suddenly No Wireless Network Card - openSUSE Forums... but I can not tell if what I have is the same problem, so I did not add to those threads. In my case I can scan for the network, and see the SSID. An ip address is assigned. But a ping does not work.
Some details, the wireless is:
Code:
04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection [8086:4235]
Subsystem: Intel Corporation Device [8086:1121]
Kernel driver in use: iwlagn
In terms of installed apps:
Code:
rpm -qa '*wireless*'
wireless-tools-30.pre8-5.1.x86_64
wireless-regdb-2009.09.08-2.2.noarch
[code]....
I know the router wireless network is good, because I can connect to the router via wireless with another laptop (old Fujitsu-Siemens Amilo 7400M with older Intel wireless), and the router wireless also works with this Dell Studio 1537 PC (with same hardware) but with openSUSE-11.3 milestone7 version.
I have a Dell E6500 with and Intel 5300 wireless agn card running Lucid x64. Wireless works fine and speeds are great except when I download with either the browser or thru a torrent or even updates. Once I get to around 100 megs in to the file wireless stops working and the only way to get it working again is to disconnect and reconnect to the AP. I have installed the back ports and tried several other fixed to get this to work but nothing has helped. One more note this happens on 2 other wireless routers that I have tried so I know that it's not limited to my Linksys.
View 3 Replies View RelatedIve installed Ubuntu recently but none of my attempts to get the wifi network working were successfull. It establishes connection but the indicator shows no signal and I cant connect to any website, I tried pinging external IPs etc. None of these worked. lspci -nn | grep 'Wireless Brand'Does not show anything. I could find 03:00:0 Network Controller: Intel Corporation Ultimate N WiFi Link 5300 lsmod | grep "wlan_module_name"Doesnt show anything. Restarting network says only: *Reconfiguring network interfaces... Kernel boot messages:
[Code]....
The network Im trying to connect to is hidden, so I have to input SSID manually, I doubt this causes the problem.
My intel pro wireless 2200 NIC doesn't work anymore. Yesterday it did, but not today (I didn't do anything special, so that it could go wrong).What is ucode and -62? Any ideas? I already checked the forums and found that ipw doesn't work when ndiswrapper is loaded. Well, I don't have it loaded. What happend?
View 8 Replies View RelatedI just installed Fedora 15 yesterday and can't get wi-fi to work. When I click 'on' on the Wireless label, it goes back to 'off' immediately. When I open the Network Settings menu and disable Airplane mode, the Wireless connection goes on and then off immediately. I took a look at /var/log/messages and it shows this:
[Code].....
Wireless networking doesn't seem to work. When I try to create a new network interface with system-config-network, my wireless card doesn't show up. The following comes from dmesg:
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: ipw2200-bss.fw request_firmware failed: Reason -2
[Code]...
I saw a post about this elsewhere and downloaded some firmware drives from [URL] and installed then. But, I'm really out of my league when it comes to this kind of stuff.
I have lenovo thinkpad, T61 with Intel 4965AGN wireless card. It is a N card, it works under N mode in windwos, but not in Ubuntu (10.10). I installed ndiswrapper and got the windows xp drivers for this card. the issue is that i got an error when installing the drivers and since then I cannot use wireless.
The error i got is: Code: Module could not be loaded. Error was: FATAL: Could not read '/lib/modules/2.6.35-24-generic/kernel/ubuntu/ndiswrapper/ndiswrapper.ko': No such file or director I unistalled the driver, but now under network connections no wireless connections appear, nothing. I cannot use wirless anymore.
i'd like to extend that ma intel wifi link 5100 is not detected no more after perform upgrade package( upgrade the kernel too ). when im using command 'lshw -C network' , there is appear to be detected, but not on command 'iwconfig' or even 'ifconfig' it just show nothin. also network-manager no longer show that ma wireless is work properly anymore.
the old kernel : 2.6.25-22 ( my wireless detected and usable )
the new kernel : 2.6.25-23 ( my wireless detected and unusable )
trying to connect wireless on wlan0 intel pro wireless 4965 AG or AGN
View 1 Replies View RelatedI swapped the wireless card in my m6400 from a Dell 1510 (Broadcom) to an Intel 5300 and I am trying to get it working. Right now it's not coming up at all. This is a running install of Ubuntu, not a new install, prior to the HW swap the Broadcom worked OK. I've searched all over, but nothing seems to address the specific problem of getting this started.
The laptop is a Dell m6400 with T9800 CPU and 4GB of RAM running 10.10 (2.6.35-22-generic x86_64).
lspci:
Code:
wprecht@LWP-laptop:$ lspci
09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5761e Gigabit Ethernet PCIe (rev 10)
0c:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300
ifconfig and iwconfig
[Code].....
Since I originally started using Ubuntu (10.04) I have had problems with my wireless card. Now I have updated to 10.10 and it has stopped working entirely. I am using a "Dell Vostro 1520" with an "Intel(R) WiFi Link 5300 AGN" wireless card.Here are the details: 10.04
In this distribution version, if I had the wireless switch on my laptop activated at startup my wireless card would refuse to activate. There is a light to show when it is activated and this was off, but I checked anyway and wireless capabilities don't work when it is in this state. It didn't even resolve the problem when I switched it off and on again (although this caused the wireless indicator to blink on for less than a second when switched on).This was manageable because I found two workarounds:
1. Wait until my laptop had logged into Ubuntu, then activate the wireless card which would start and work as it should.
2. If I had already logged into Ubuntu I could put my computer on standby, switch off the card, come out of standby and reactivate the card while Ubuntu was running.As I said, this was completely manageable, and I got used to it. 10.10
Now that I have upgraded to 10.10 all workarounds fail, I can't use a wireless connection in Ubuntu, as my card won't activate, I cant even get the light to blink as I could before. The only way I can use WiFi is by switching to Windows.I tend to use Ubuntu for my university programming work.
Are Intel wireless cards compatible with non-intel-based laptops? In my case I wish to upgrade the current Atheros-based mini pci express wifi card with the Intel 4965agn. It is an Asus 4520 with an AMD Athlon X2 processor and nvidia nForce chipset.
View 1 Replies View RelatedI'm running Linux 11.04 and my wireless network was working just fine until today. I cannot connect to WiFi - it acts as if the device wasn't there. The hardware switch led isn't working. No matter how much clicking on it, it won't work.
iwconfig:
Quote:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm
[Code].....
I have a dell 1521 and I can't get internet working, I thing the driver is no working with ubuntu 9.10
View 1 Replies View RelatedI want to switch my laptop from XP to Ubuntu, but right now, i cant risk installing it. i dont want to have it partitioned so i can dual boot, so for now i only run the try-it-out mode.Before i consider installing though, i want to see if i can get everything to work ahead of time, that way im not regreting instalation. I have a Compaq Presario V2000 laptop, with 55GB hard drive and 516MB ram. So far, the trial mode is working great, but the wireless will not work. Ive tried to install the driver, but i am unable to do so. I have looked this up, and i have tried many things, and so far, none have worked.I was wondering if it was just part of the trial thing or not, but it is a Broadcom Wireless BCM4318 driver
View 9 Replies View RelatedRecently I have installed Fedora 14 on my other laptop. It's a dual boot with Windows 7. Everything worked perfectly fine, networking included, until my friend didn't accidently turned off the wireless by pressing a wireless button on the laptop. Since then the wireless on Fedora doesn't work. It does on Windows thought. I've tried restarting the laptop few times, but the wireless still doesn't want to work again.
View 2 Replies View Relatedi installed ubuntu along side of xp, and i cannot get my wireless to work. the drivers that are installed in xp work great, and i can access the internet, but do not work in ubuntu.
View 3 Replies View RelatedI have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
[code]...
I have an IBM ThinkPad W700 running 64 bit Ubuntu 9.10 Karmic Koala. At the office I normally connect it to the Ethernet since it's never connected very reliably to the wifi there (drops out 2 or 3 times per day, usually at the worst possible time, of course), but it always worked just fine with Netgear WGR614v5 at home... until a week or two ago.
I used to be able to come home, take the laptop out of suspend mode, and it would connect to the wifi. Occasionally there'd be some hitch and I'd have to restart the network manager (sudo /etc/init.d/network-manager restart) but this was only sometimes, and when I did, it'd always work. But now, when I get home from work, I need to restart the entire system to get it to connect properly again. Without restarting the whole system, it either doesn't scan for wifi networks, it doesn't find any wifi networks, it keeps stuffing up my wifi password, or it connects and gets 0% signal.
Presumably, some driver was updated recently and it doesn't work so well. What's the easiest way to find out what drivers have been updated lately, and revert to a previous version? And what else can I try restarting so I don't have to restart the entire system? I've tried /etc/init.d/network-manager restart, /etc/init.d/networking restart, /etc/init.d/network-interface restart, and restart network-manager. I've also tried turning the wireless switch at the front of the laptop off and on, many times.
Code:
$ lspci -nn
[...]
03:00.0 Network controller [0280]: Intel Corporation Wireless Wifi Link 5300 [8086:4236]
[...]
$ ifconfig wlan0
[Code]...
The info above is when I've taken my laptop out of suspend mode and it won't connect to the network. lsmod doesn't say anything about wifi nor wireless; iwlist does see my network, which my older Januty laptop is connected to without drama.
I am using fc14 i686, and I am having a problem with my wireless card. Even though the led of the wireless card lights up the network manager claims that the wireless is disabled. I don't understand what is going wrong.I am a newbie trying to be sth better bur for the time being my only help could be the outputs of the lshw, lspci and lsusb commands.
View 5 Replies View Relatedi have an Acer aspire 4920 laptop with opensuse11.3 installed and wifi card has identified home wifi, but for some reason when i enter the wpa-psk key it doesnt connect.i have been at this problem for several days and scanning the net for answers, without joy.i dont know about the command or terminal line, i have tried to type in commands but i get no joy.
View 4 Replies View RelatedI am running openSUSE 11.3 updated with all the latest patches and I cannot connect to my wireless router. I am running Linux Mint 10 on the same type of notebook HP Compaq 6910p and it worked right after the install. If I take off the security WPA & WPA2 Personal I can connect. lspci -v | less shows this for my wireless card.
10:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
Subsystem: Intel Corporation Device 1000
Flags: bus master, fast devsel, latency 0, IRQ 29
Memory at e4000000 (64-bit, non-prefetchable) [size=8K]
[code]....
I am using the same settings for both notebooks just can't figure out why openSUSE 11.3 won't connect. I get the prompt to key in my password, I've even checked the box to show password to make sure I was keying it in correctly. Everything was good but it just goes right back to the password prompt after it fails trying to connect.
I'm releaving a HP Probook 4710S from it's native Vista) First of all let me say I'm happy because CentOs 5.6 handles it's Ati Radeon graphic flawlessly, unlike other Distro's I tried on this type of machine. So thumbs up for CentOs! But now I've come to a stop on the wireless card.
[Code]...
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View RelatedWireless worked fine on live cd, but for some reason not after install. I think maybe the driver is not loading, but I am a pretty much still a noob, so my opinion isn't worth much. If it is the driver not loading, I don't know what to do to fix it. Here is my wireless output information.
Code:
linux:/home/linux # lspci -nnk
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Toshiba America Info Systems Device [1179:ff10]
Kernel driver in use: agpgart-intel
[Code]....
A friend who switched ISP's gave me his old Linksys WRT54-G wireless router. I went through the installation procedure and had a wireless connection up and running - smiley face. I had security set up for WPA, and decided to upgrade it to WPA2. Another smiley face. When I went to connect (had already done so successfully), I noticed it referred to my wireless as Linksys - I was expecting to see the SSID. So I started playing around in Network Manager and now I have things all effed up.
Don't know exactly what I did, but now I have no wireless. So I ran a few commands (lshw -C network, iwconfig, ifconfig, and iwlist scan), and looking at the results I see what appear to be inconsistencies in the output. I've posted them below, and make the following observations:
1. Under the lshw it refers to my wireless connection logical name as wmaster0, and has the correct MAC address, etc.
2. Under the iwconfig it says, 'wmaster0 no wireless extensions', but then refers to wlan0 as the wireless connection (although it does not seem to be running).
3. Under ifconfig I see both a wlan0 and a wlan0:avahi. The wlan0 has no IP, the wlan0:avahi does, but it is incorrect.
[Code]...
how to set up wireless networks. The technical language is foreign to me. My notebook maybe described as follows:
Make and Model: SONY VAIO FW490
Processor: Intel� Core™ 2 Duo Processor P8700 (2.53GHz)
RAM: 4GB DDR2-SDRAM
Graphics card: ATI Mobility Radeon™ HD4650 graphics card with 512MB vRAM.
[code]....
It came pre-installed with Windows Vista Home Premium but now I have Fedora 11 (w/ Gnome) as the only OS. The router that I am using with an Ethernet cable connected to my laptop is a Netgear 54Mbps Wireless Router WGR614 v7 connected to a Motorola Surfboard Cable Modem. Both worked right out of the box and now I have wired Internet access. RCN is my ISP. I would like to avoid using the Ethernet cable connecting my laptop to the router.
This is what I have done so far:
1. Gone to System>Administration>Network
2. Clicked "New" then chose "Wireless connection" from the list
3. Chose Intel Corp. Wireless WiFi Link 5100 (wlan0) from list. The other option was "Other Wireless Card".
I don't know what to do after this. What should I choose in the windows entitled "Configure Wireless Connection" and "Configure Network Settings" ? I chose Ad-Hoc for mode and entered an SSID name even though I have no explanation for taking these actions. As for the other settings, I simply went with whatever was already selected. At the moment, I lose Internet access when I disconnect the Ethernet cable. I see other wireless networks when I click the network icon on the top right corner of the screen. I don't know how to make my router appear on that list if that's necessary.
Have been running Fed 11 on this laptop (dual booting with windows) for some time with no issue's. Removed 11 and installed 13. I now cannot get my wireless adaptor to pick up. Drivers are loaded and sees the card in lspci, here is some log outs I have made:-
[Code].....
