My network is running a cable modem (ISP), router, then I have a laptop that host some services (ftp, etc). It would be nice if I could build a small computer that could also have an WAP. That way I could have a wireless router and NAS, proxy server all in one.
View 4 RepliesI obtained some old PC and I've installed debian linux on it. Now, I have onboard ethernet slot (10/100) and net works fine. Into PC's usb slot I've plugged Bus 001 Device 002: ID 0bda:8189 Realtek Semiconductor Corp. RTL8187B Wireless 802.11g 54Mbps Network Adapter and I want to know is it possible to transform this PC into wireless router for home use? If so, what do I have to do?
View 3 Replies View RelatedI am running openSUSE 11.2 and just recently my network has been down. I'm using Gnome, but using Yast to configure my network (I'm usually forced to use wireless as I travel a lot on my laptop). Usually, when I'm connected to a wireless network, it will show up as so in the Gnome start menu, but recently, it will only say Wired there, even though I have nothing connected to my ethernet jack. I can connect wirelessly to a home router, but cannot use the wireless in any other way. I have tried manually disabling the ethernet connection to no avail. Unfortunately I am limited in my linux knowledge, so I am kinda stuck here.
View 1 Replies View RelatedI just installed WUBI and tried to connect to my home router but am unable to. I can connect to nearby unlocked routers, but am unable to connect to mine which is WPA-PSK [TKIP]. Also, this is the first time I've even seen Ubuntu
View 4 Replies View RelatedThe garage in my house is a dead spot for my current wifi router.I can't get a signal there.Moving my router within the limits of my cabling doesn't fix it. But I have two other routers I'm no longer using.Is it possible to use one of them as a wireless access point to extend the range of my current router?If so, what is the general procedure for doing that? My main router is a Verizon Actiontec M424WR. My other unused routers are a D-Link and a Netgear, both of which have wireless capability. The Netgear had a superior range, as I recall.
View 8 Replies View RelatedIs there a utility to forward ports on a simple home networking wireless router from commandline using upnp?
View 1 Replies View RelatedMy son lost his USB Wireless stick for his Computer. I had thought I heard that if you had a second wireless router, you could use it somehow to detect the wireless router you have already set up in your home (like using a wireless card)? Is this what Ad-Hoc is? Either way, can this be done and if so how? I use a WRT54Gx2 Lynksys router and have a TRENDNET TEW-432BRP wireless router and also a spare D-link DI-514. I use ubuntu 10.04, and also wanted to know if I connected one of the router to his on the LAn port could he connect msaybe through an Ad-Hoc on my local computer here? He uses XP on his. I'm a newbie to linux and networking in general.
View 2 Replies View RelatedI moved my server and network equipment, and now the wireless works but I cannot get my server online. I host a website, so this is kind of urgent.
I have a wireless router and can access the internet fine on my laptop. My server is wired & connected to the router. It sets up the networking properly.. ifconfig has an ip address, the default gateway is present. But I cannot ping google, or even the router. It says destination host unreachable.
So I go back to the laptop to check the router settings.. sometimes it likes to assign the server the wrong internal ip. But, I can't access the router settings either! The page (192.168.1.1) times out. Same with trying to ping the router. How can the laptop be online if it can't reach the router?
Oddly, ifconfig on my laptop reports an ip address starting with 99.233. It's always given me an internal address starting with 192.168. What's going on here? Is the router not allocating an internal ip? I use wicd to connect, if it's relevant.
We have a windows laptop that can only get a "local connection". Now it does sound like the router is forwarding directly to my laptop, instead of allocating internal ips.
I have a Toshiba Satellite L550 laptop with Suse 11.3 dual booting with Windows 7. Windows can detect the built in wireless card but not Suse, what can I do to get the wireless recognized in Suse.
View 2 Replies View RelatedThis is my basic setup:
[URL]
I don't know how to get the wireless router to connect to the other wireless router so I can use internet on my computer. How do I achieve this wireless connection?
I want to set up a Linux box as a wireless router to replace our existing Netgear WNR1000 router, as I believe the Netgear does not support the coming IPv6 protocol. Unfortunately, it is not flashable with OpenWRT or DD-WRT presently.
As we have Comcast, our cable modem acts as a dumb modem according to the customer support guy I talked to, and our router is the one that asks for the IP address from DHCP. Thus, when Comcast switches over to IPv6, I don't believe my existing router would work, correct?
My idea is to take a Linux box and put two NICs and a wireless adapter in it, using IPCop or Smoothwall to set up a router. I could then enable IPv6 support for when we have IPv6 with Comcast. Is that possible? Would there be a way to get BIND to hand out private IP addresses in the same subnet on the both the LAN NIC and the wireless card?
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
I'm using a cross-over ethernet cable to connect a Desktop Windows 7 box, and a laptop running on SUSE 11.2. I want Windows to connect to the internet via the laptop's wireless interface.
View 1 Replies View RelatedI am running fedora 14,
have 456.2 MB RAM
59.9 GB disk space
Kernel 2.6.35.13-91.fc14.i686
Intel Pentium 4 CPU 2.00Ghz
SIS motherboard
Unknown brand sound card
Have tried tried the following music apps
-Amarok
-Audacity
-Banshee
-Rhythymbox
-Kaffiene
-Movie Player
Have played
-mp3
-m4a
-wav
Used several diff speakers and heaphones
What is the problem?
My first problem is that when I open KNetworkManager the wireless tab is desibled,I don't know why! My laptop is HP pavilion dv6-1245DX. How to get connected to my wireless router?
View 9 Replies View RelatedI have an old T30 that has an incompatible wireless card with my network. How can I disable the builtin wireless card while allowing my USB Linksys card to fully function?I can't figure out how to have one run while disabling the other.
View 4 Replies View RelatedI was going to buy a TP-link wireless router (802.11b/g/n) but while I was reading the consumer's reviews I saw some people were saying that they couldn't make it work with ubuntu. So, I'm starting wandering if there is somewhere any compatibility list? I mean if for instance TP-link or D-link would work with broadcom's chip. I would like to use my laptop's built-in wireless module which is HP Broadcom corp. BCM4306 802.11b/g. My laptop is a HP Pavilion zv6000.
View 2 Replies View RelatedAfter seeing a few articles on making a home router I thought "I'll have a go at that" as I've spare bits and bobs lying around. Now apart form some iffy wireless cards one major problem sprung to mind. Clearly there will be 2 NIC - 1 in and in my case one out. And that one has to be wireless. But I've yet to find a ready built one (is Smoothwall or the like) that will allow me to do this with a wireless network card in the machine.
Firstly is it doable as all the traffic in my house is wireless. Secondly are there any ready built distros that will handle it for me.
I want to try to get wireless access to the wifi router with the xbox360 wireless network adapter.Is this possible?
View 1 Replies View RelatedMy PC is connected directly to the cable modem. I would like to use my PC's WiFi card to share my internet connection with my Android phone and laptop so I can avoid buying a wireless router.
View 4 Replies View Relatedwlan0 Authentication capabilities :
WPA
WPA2
CIPHER-TKIP
CIPHER-CCMP
Those are my authentication capabilities, obviously. I am using a WEP encryption for my wireless router and according to this, it will not allow me to connect. Is there anyway to allow that? The wireless card works just fine in Windows, even on the same network encryption type. Using a Intel Wireless/Pro 4965 ag. Note* this is my mother's router and whatnot. She won't change it the encryption type.
I'm using LiveCD to test my laptop with FC 14. It booted from the LiveCD image last night, but my wireless didn't work. I need the madwifi wireless drivers for my built in Atheros adapter.
Can I download the latest and greatest madwifi drivers, compile them and use them while running from the LiveCD image?
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View RelatedI installed a Tenda W322P wireless card in my dual-boot PC running both Windows XP and Ubuntu 11.04. The card worked straight out of the box on XP, but does not function correctly under Ubuntu. My apologies for any missing/irrelevant information, I am having to post this from the Windows boot so the Ubuntu settings are not directly available at the same time as internet access.I followed the process detailed here htURL...to install and configure the driver (I believe from reading other sites that this card is the Ralink RT3062 chipset), blacklisted the original RT2860 driver that was in use (couldn't even get the card to scan for wireless networks with the default driver) and restarted the interface.
Since then, sudo iwlist scan can find my wireless router but when I attempt to connect to it, it seems to enter a loop of requesting the WEP key then pausing for a while before re-requesting the key. I know I have the key value correct because it is copied and pasted from the same text file I used to copy and paste into the passkey field on the Windows boot. Attempting to connect to the router using Ubuntu also has the rather unfortunate side-effect of crashing the wireless router, killing off all other device connections until the router has been reset.
I'm wanting to set up a network. I'm still confused as to how to set it up. I think the easiest design is to have a switch on my border router.n this switch will be the servers. Also attached to this switch will be a Linux box. This will be a dedicated firewall. On it will be another switch. And the machines on the internal network will be attached to this switch. In the book "building Internet firewalls"(o'reilly) this set up is described as a screened subnet architecture. However the external interface on the Linux dedicated firewall will have to get it's I.P via dhcp (192.168.1.*) from the border router.
That or it can be a static I.P on the same subnet as the border routers dhcp range 192.168.1.*(but outside the dhcp range) but that would be trickier.The internal interface of this dedicated firewall would be static and on a different subnet as the external interface (192.168.2.*). Then this internal interface could give out I.Ps to the internal network that are on 192.168.2.*. If it did N.A.T for packets from the internal network then N.A.T would be being done twice; once by the Linux dedicated firewall and once on the border router, before going off to the net.Or is it a better approach to NOT do N.A.T on the Linux firewall and have all I.Ps on the whole network assigned as static(outside of the border router's dhcp range, but all on the same subnet(192.168.1.*))?.
Basically is there any point in the Linux box doing dhcp and N.A.T for hosts on the internal network?. I guess the answer is no. But i just wanted to hear your opinions, if you have the time. The border router is a home router. nted to have a normal triple-homed dedicated firewall and put it in the border router's DMZ but it proved unpredictable and tricky. So i just wondered what the best I.P addressing scheme would be for my newer way.
I updated a firmware of my wifi router (small black box with antenna). The router is managed via web browser at address 192.168.1.100. I opened Mozilla Firefox connected to the router, but a 'home.asp' application - an interface one can to set up a configuration - running on the router didn't work properly. When I tried to change some settings, and eg. clicked a confirmation button nothing happened. I solved the problem staring Windows and making a connection using IE - this time that home.asp application did OK. The question is what may caused problems? A bug in this app or in general *.asp applications don't communicate well with browsers other than IE or simply they don't 'like' Linux?
View 7 Replies View RelatedHow can I successfully SSH using SecureCRT from the Internet to my Centos Linux box at home behind the router? I have a DGL-4500 dLink router. I configured a Virtual Server in the router for SSH 192.168.0.182 Protocol 6 TCP public port 22 ? private port 22 Schedule Always Allow Inbound Filter Allow All. Further I Enable DMZ for 192.168.0.182. I got my Internet IP address through "what is my ip website." Now every time when I try to SSH, I get a message "The remote system refused the connection". Here is iptables -L command output;
[root@localhost ~]# iptables -L
Chain INPUT (policy ACCEPT)
target prot opt source destination
RH-Firewall-1-INPUT all -- anywhere anywhere
Chain FORWARD (policy ACCEPT)
target prot opt source destination
RH-Firewall-1-INPUT all -- anywhere anywhere
[Code]....
My wireless connection work just fine but it gives me wrong connection status, like 10% even when I'm seating near the wireless router or disconnect status while I steal manege to use the internet at full speed.
View 1 Replies View RelatedI can connect to my wireless router while logged in as root, but not under my user account. I went into YAST and the user maintenance area and gave myself every permission (Add, Edit, Delete Users or Accounts), but kde network maanger will not allow me to connect to my router.
View 5 Replies View RelatedI'm try to setup a wireless network with my linksys wireless router and my HP laptop dual booting Vista & Suse 11.2. I have the vista networked, just fine. Where I can share files and the printer connected to my desktop. But I want to be able to use Suse in the same way, full time and to stray away from Vista. My wife and kids like easy. So I'm trying to transform them and show them something new.
View 9 Replies View Related