I'm using a cross-over ethernet cable to connect a Desktop Windows 7 box, and a laptop running on SUSE 11.2. I want Windows to connect to the internet via the laptop's wireless interface.
View 1 RepliesI have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
net.ipv4.ip_forward=1
Then I tried this on the laptop:
sudo iptables --table nat --append POSTROUTING --out-interface ath0 -j MASQUERADE
sudo iptables --append FORWARD --in-interface eth0 -j ACCEPT
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
My son lost his USB Wireless stick for his Computer. I had thought I heard that if you had a second wireless router, you could use it somehow to detect the wireless router you have already set up in your home (like using a wireless card)? Is this what Ad-Hoc is? Either way, can this be done and if so how? I use a WRT54Gx2 Lynksys router and have a TRENDNET TEW-432BRP wireless router and also a spare D-link DI-514. I use ubuntu 10.04, and also wanted to know if I connected one of the router to his on the LAn port could he connect msaybe through an Ad-Hoc on my local computer here? He uses XP on his. I'm a newbie to linux and networking in general.
View 2 Replies View RelatedI moved my server and network equipment, and now the wireless works but I cannot get my server online. I host a website, so this is kind of urgent.
I have a wireless router and can access the internet fine on my laptop. My server is wired & connected to the router. It sets up the networking properly.. ifconfig has an ip address, the default gateway is present. But I cannot ping google, or even the router. It says destination host unreachable.
So I go back to the laptop to check the router settings.. sometimes it likes to assign the server the wrong internal ip. But, I can't access the router settings either! The page (192.168.1.1) times out. Same with trying to ping the router. How can the laptop be online if it can't reach the router?
Oddly, ifconfig on my laptop reports an ip address starting with 99.233. It's always given me an internal address starting with 192.168. What's going on here? Is the router not allocating an internal ip? I use wicd to connect, if it's relevant.
We have a windows laptop that can only get a "local connection". Now it does sound like the router is forwarding directly to my laptop, instead of allocating internal ips.
I want to set up a Linux box as a wireless router to replace our existing Netgear WNR1000 router, as I believe the Netgear does not support the coming IPv6 protocol. Unfortunately, it is not flashable with OpenWRT or DD-WRT presently.
As we have Comcast, our cable modem acts as a dumb modem according to the customer support guy I talked to, and our router is the one that asks for the IP address from DHCP. Thus, when Comcast switches over to IPv6, I don't believe my existing router would work, correct?
My idea is to take a Linux box and put two NICs and a wireless adapter in it, using IPCop or Smoothwall to set up a router. I could then enable IPv6 support for when we have IPv6 with Comcast. Is that possible? Would there be a way to get BIND to hand out private IP addresses in the same subnet on the both the LAN NIC and the wireless card?
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
i wanted to know if i can use my laptop as a wifi router; with encryption password and all security so if another computer is in the range can detect the signal and then try to connect to it with the encrypt pass.
also i have one more doubt. can a wireless router be used as a wifi ethernet card and detect wifi signals nearby and connect to internet. suppose i have a wireless router and i connect it to my desktop(with lan cables) which has ubuntu installed, and theres a wifi connections nearby can i connect the desktop to the internet.
I'm try to setup a wireless network with my linksys wireless router and my HP laptop dual booting Vista & Suse 11.2. I have the vista networked, just fine. Where I can share files and the printer connected to my desktop. But I want to be able to use Suse in the same way, full time and to stray away from Vista. My wife and kids like easy. So I'm trying to transform them and show them something new.
View 9 Replies View RelatedI am using ubuntu lucid and am able to connect to my ThomsonTG585 wireless router, but my mother who uses win7 is unable to connect, except by Ethernet cable, which is not convenient, how can I get her connected. When I try to connect, It it says "limited connectivity" and does not let her utilize the internet. My brother is dual booting ubuntu karmic and winXP and is able to connect on both os's. I am absolutely sure I am entering the correct pass-phrase and ssid.
View 6 Replies View RelatedRunning Ubuntu 11.04 on a Gateway LT3103U netbook. It's running fine except for that fact that when it goes to sleep (timeout or lid closed) or going into suspend or otherwise restarted/shutdown, my router restarts. It's a DLink DIR-655 that has been working fine until I changed this netbook to Ubuntu.After installing Ubuntu on the netbook, it found my SSID being broadcast and I added the connection by supplying the WPA2 password. I have full network access (local and internet).
It's just the router restarts and all my other machines lose connections. The router is using DHCP but supplying IPs based on MAC. Netbook is set to use DHCP.
I was wondering whether or not it is possible/advisable to install and run Snort on a single laptop with a wireless router (firewall enabled)? Does Snort require root privileges and are there any other issues one needs to be aware of when installing and running software like this?
View 6 Replies View RelatedThis is my basic setup:
[URL]
I don't know how to get the wireless router to connect to the other wireless router so I can use internet on my computer. How do I achieve this wireless connection?
Environment
Linksys WRT54G Wireless
Laptop wireless Windows/XP
Windows/XP Hyper Terminal
Desktop Server Linux OEL 5 (not wireless) cable connected to the WRT54G router port. (I can go to the Internet with this server, but not able to communicate other computers on the WRT54G Wireless Network. Even though, the Linux Server is connected to the WRT54G router port.) From the Hyper Terminal Wireless laptop Windows/XP, I want to connect to my Linux Server.
My PC is connected directly to the cable modem. I would like to use my PC's WiFi card to share my internet connection with my Android phone and laptop so I can avoid buying a wireless router.
View 4 Replies View RelatedI have a very strange problem with my wireless routers, or linux. I have 2 wireless routers one directly connected to my modem (router 1) and another wireless router (router 2) on the 2nd floor connected to router 1 without cables and configured as a repeater bridge. Router 1 is configured to broadcast the ssid and have been set up to use wpa-personal and router 2 has the same configuration as router 1 plus a virtual interface.
I am able to connect to both routers from all my windows boxes, but I fail to connect from linux (I have tried with 2 different laptops without luck). What is very strange is that I can't see the routers when I scan but I am able to see my neighbors routers. I have tried to turn off router 2 to see if it had an impact, but no luck. I know that I am able to connect to a wireless router since I have had success with that at work.Router 1 is a Siemens se551 (with default firmware) and router 2 is a linksys wrt54g (running DD-WRT build 13064).
I just downloaded ubuntu 10.4 today. I can't seem to figure out how to connect to the Internet.
View 7 Replies View RelatedI have a desktop running Ubuntu 9.10 with a D-Link WUA-1340 (Supported - last on list) USB wireless adapter, through which I would like to set up a wireless network for internet connection sharing at home.
I have 2 ethernet adapters on my desktop (Eth0, Eth1), and an Apple Airport Express, which I initially tried to use, then thought it might be better to just bypass the Airport Express.
My problem is that although I create a wireless network and connect to it with my macbook, I am unable to access the Internet on it.
I am not sure what I am doing wrong, and have worked through WifiDocsShareEthernetConnectionThroughWireless a few times, as this seems to be exactly what I am trying to do.
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies View RelatedCan I use Mint as a Router service, similar to the service in Ubuntu (called: Router Advertisement Daemon?). Does Mint support this and what solutions are available for this?
Have dabbled in Linux very briefly, but almost no experience on how to install or find programs, so please explain in detail!
EDIT: I'm looking for something easy and simple, like what Virtual Router or Connectify does for Windows 7...
I obtained some old PC and I've installed debian linux on it. Now, I have onboard ethernet slot (10/100) and net works fine. Into PC's usb slot I've plugged Bus 001 Device 002: ID 0bda:8189 Realtek Semiconductor Corp. RTL8187B Wireless 802.11g 54Mbps Network Adapter and I want to know is it possible to transform this PC into wireless router for home use? If so, what do I have to do?
View 3 Replies View RelatedThere's only one thing preventing me from completely making the switch from Lose-dows to Linux: inability to connect my laptop wirelessly. I'm currently using an old IBM Thinkpad with an Intel Pentium III, 1.13 GHz with 384 megs of RAM. The wireless is through a Belkin USB dongle (model: F5D8053, v3) and a Netgear Duo Wireless-N Router (model: WNDR3300). Let's say, for sake of argument, I'm using Linux Mint Julia. It clearly must recognize the USB dongle, because it can detect all the other networks in the area, including the Netgear. But it won't connect to it, or any of the secured ones.
So what's the deal? It'll connect when connected directly, so it's not the computer. Or is it? All I know is I'll have to wait til I get an LFC interface (LFC=Long F**king Cable) before I want to connect Linux to the net.
I am trying to get an arp packet from my wireless wifi router (access point), to which I am not connected. I simply tried ping 192.168.0.1, but the answer was connect: network is unreachable. What can I do about that?
View 1 Replies View RelatedI have a complicated situation due to my goals and network structure. I have in mind a potential solution, a bridge, but I do not know whether it is feasible or what hardware it will require.
The network:
My apartment community provides residents with free Internet access through an ancient T1 line. We do not have the option of other Internet providers, so having a router and modem in the home are not an option. The T1 line is split among some 24 switches, one for each building, and each switch has one port per floor. At each floor, there is a D-link WAP, and each has a separate SSID and WEP key. Additionally, they control access at the switch level using Access Control.
My goals:
I'm used to being in control of my networked environment. I like to have friends over often, and most of them have a laptop, a smart phone, or both, which makes Access Control a pain. I don't want to have to think ahead and get their MAC addresses to the IT consultant while he's here during business hours. My wife and I have 6 devices, two of which require an Ethernet connection.
I use a few applications for streaming that utilize UDP (I'm not sure if the WAPs are smart enough to even handle this) and I don't like having my traffic muddled with my neighbors.
I should note that I tried extending the network with my Airport Extreme router, which apparently only works with other Apple devices. I've also looked into WDS, but that seems to require an unlikely amount of cooperation from the IT consultant on site.
The potential solution: a Linux server that acts as a router. Ideally, it could act as a webserver for a small static site as well, but let's focus on the routing. I'd like to bridge two NICs and use masquerading (Internet Connection Sharing). The public interface would connect to the WAP using WEP. The private interface would allow up to 8 devices to connect to the server.
It seems easy enough to configure the public interface, and even to bridge the connections. What I've never done before is purchase a wireless card that can accept multiple clients. Maybe they can all do this?
want to connect a linux server using centos 4.8 onto a wireless router. then clients will access mails/internet using the wireless router. how do l go about it. anyone with an example
View 4 Replies View RelatedRunning Suse 11.3 (Gnome) on an Acer Aspire 5310 Laptop.Installed all the default broadcom drivers via install software.The following I tried:
/usr/sbin/iwlist eth0 scanning
eth0 Interface doesn't support scanning.
bodifee@linux-wv6l:~> /usr/sbin/iwconfig
lo no wireless extensions.
[code]....
So card still not active i seems.Have deleted and added wireless adapter
I'm using crux 2.7. I'm connecting from the command line and I successfully get an IP leased. Usually 192.168.1.3
But still I can't ping my router.
I've never encountered this and I'm not sure how to trouble shoot it. The router is working just fine. The problem is with my Crux setup.
I have no internet and no GUI installed yet.
I have Ubuntu(k)partitioned with WindowsXP home edition(sp3) on a Dell Dimension 9100 MN: 0x8582 512mb RAM; NVIDIA geForce 7600 GS 266Mhz; Intel Pentium 4 630 CPU 3 Ghz. I'm using Lynksys Wireless-G PCI Adapter /Speed Booster MN:WPM54GS and have downloaded NDISWrapper and NDISGTK.
View 8 Replies View RelatedThese r IP provided by my ISP that i've put on Fedora 8:
WAN IP:xxx.xxx.xxx.17 (eth0)
Subnet:255.255.255.252
Gateway:xxx.xxx.xxx.18
Valid static(public) IP set of 2:
IP:xxx.xxx.xxx.147 & 148 (eth1, eth2)
Subnet:255.255.255.240
i want to run xxx.xxx.xxx.147 as a web server & xxx.xxx.xxx.148 as a ftp server. but I'm able to ping only xxx.xxx.xxx.17(WAN IP) from outside world. Can any1 tell me that how can i bring my 147 & 148 IP online without router.
it started with rooting my Motorola Droid. I got quite interested in the whole rooting/linux "world". The only problem is, my hands move A LOT faster than my brain does. I'm an "educated novice" at best when it comes to all of this and still learning slowly, but surely. I followed an online tutorial and before I realized quite what i'd done, I had dual installed Ubuntu linux 10.10 on my laptop. ISO'd this, partitioned that and realized....i'm in way over my head. Then I started researching how to just go back in time and get my "safe" windows vista back until I'm ready to make the switch to linux and just ended up getting more confused.
How do I actually BOOT into Windows on a dual boot computer that I apparently just created? How, if need be, do I undo everything I just did in the past few hours and careless tinkering? If I decide to stay with Linux, how do I get my damn wireless router to recognize?
RT2500 wifi card could not connect to wireless router using WPA personal.OS - RHEL4; Dell Inspiron C600; interface detected ra0
View 12 Replies View Related