My old xp is too slow, so I am intending on re-installing from scratch. I will first raid 0 my drives. Then install XP, followed by Ubuntu. From browsing on net it seems many people have problems with dual booting. (I did several years back). Any simple Free boot managers that are tried and tested. Can/will do some editing of Boot manager if required.
View 3 Replies
We are trying to set up a livestream to make it possible to have the video from an HD (720p) outdoor security IP camera (h264) and use this on a few websites and use it as a demo to show what the possibilities of IP-television are. We also want to be able to stream it to some settop boxes that are in a customer environement in use. the big deal here is to take the stream from the camera on the on the server.
It would be nice to be able to interrupt the stream to show some other vids or pictures or some interactive messages. I have seen lots of these kinds of "local tv channels" but I don't have a clue how to set it up...
Uplink, money(well...) and hardware isn't really a problem.
I just built a home computer with 3TB hard drives I wanted to set up in a RAID 5 and load Ubuntu server onto it. The first thing I did was set up the drives in a RAID 5 using just the motherboard chipset software to do it, so a 'hardware' RAID basically. I installed Windows first to see if all the hardware works ok (that seemed the easiest way to verify it) and with the exception of the ethernet card (which needed a driver disk to work) everything was plug n' play and worked wonderfully. After that I booted the Windows install disk again to delete the partitions, hoping Ubuntu 10.10 server would create its own.
The problem I'm having is no matter what I've tried (deleting and recreating the RAID 5 setup, departitioning the drives), whenever I try to install Ubuntu it won't recognize the RAID as a valid disk. Ironically, it did at first, because I installed windows to verify the hardware. The ethernet card wasn't working automatically in the Ubuntu setup, (although it found the unformatted RAID drive), so I installed windows and figured out it was just the drivers that needed to be installed.
So now when I try to install Ubuntu, it finds the ethernet card perfectly and connects to the internet during the installation...but that actually stinks because it's telling me it's still accessing the drivers from the drives that I thought I formatted. Once it gets to the storage part of the installation afterwards, it can't find the RAID drive anymore. I tells me to choose a disk from the list, but the list is blank. So I can't install on it.
If I remove the RAID entirely and just keep the drives as 3 separate IDE drives, it finds every drive perfectly and can install to either one I choose. But I don't want this, I definitely need them RAIDed.
How can I mirror drives on the hardware level? I have a Sun X2270 server with 4 1 terabyte hard drives and need to mirror two drives.
View 1 Replies View RelatedI've installed Debian (Lenny) on my pc, with geForce 8500 GT, two monitor (LCD + CRT). i've correctly installed the driver i can enter in the nvidia's setup but:
1) the best resolution for my CRT (Sony Brillance 109P) is 640x480
2) video on LCD (LG Flatron L222WS) is no good bat I can setting different resolution
3) I can't save the XConfig cause i don't understand what permission I must have for writing on 'etc' folder
so I have been messing around with the new Vector 7.0 alpha and wanted to install the nvidia driver and see if it would work. my video card and cpu are as follows
Code:
root:# lshw
PCI (sysfs)
vector.linux.net
description: Desktop Computer
width: 32 bits
[Code].....
i need drivers for monitor 17' adi nh 776 for linux bt4.because i cant change resolution at nvidia xserver setting...
View 6 Replies View RelatedNormally I use disper to enable my external monitor, but I don't think I can force the 2nd monitor to be primary. [URL]
I've played around with nv-control-dpy included in the nvidia-control source, but I haven't figured out how to do it yet. How to get: [URL]
This is a laptop, to which I connect an external hdmi display when I get to work. dipser -e extends the desktop for me, but the laptop remains the primary desktop (holding the panels etc). nvidia-settings can set primary monitor for me, but I want to use the cli.
I bought SuSE 8.0 professional a long time ago, while living in Germany. I have an old German laptop that currently has Win2K installed, and I would now like to replace Windows with Linux on it. The computer boots the initial CD fine and gives me a number of installation choices. If I do not add a "root=/dev/hda1" to the parameters it stops the installation with a "Kernel panic: VFS: Unable to mount root fs on 08:01" and if that line is there the error message changes to 03:01.
Is this because the hard drive is already formatted to NTFS? Is there a way to delete the partition and create a new one from the Linux installation disks?
I just installed Red Hat Linux Professional 8.0 in my VMWare, but I do not know how to start X Windows. I have tried to type "startx" on "RUN", but I get error message: Fatal Server error Server already active for display 0. If this server is no longer running, remove tmp/.X0-lock and start again.
View 1 Replies View RelatedI'm in the process of setting up my very first ubuntu server.
Using 10.04 and has 2gb ram
I am using Ubuntu's software raid (mdadm)
It will be a file server, with 4 hard drives (3 in RAID5 and 1 as a spare)
All 4 drives have 2 partitions:
Partition 1 - 100mb
Partition 2 - The remaining drive space
I setup the first 3 drives' partition 1's to be RAID1 with the 4th drive's partition 1 as a spare. This is where I'm mounting "/boot" (it's my understanding that /boot cannot be on a RAID5). I setup the first 3 drives' partition 2's to be RAID5 with the 4th drive's partition 2 as a spare. This its where I'm mounting. I believe so far I'm setup correctly to be able to deal with a drive failure and the system should operate just fine. What I don't know what to do is with the /swap. I want to retain the ability to be able to operate with a drive going down. But I have also read warnings about putting /swap on a raid. How would you setup /swap?
I just installed Ubuntu 10.10 64bit and wanted to get access to my nvidia RAID array. This array is working, and is NTFS formatted. But wasn't showing up through normal means in Ubuntu. (for example the NTFS Configuration Tool didn't display it) Here's what the system showed.
Code:
root@hermes:~# ls -l /dev/mapper/
total 0
crw------- 1 root root 10, 59 2010-11-03 22:39 control
lrwxrwxrwx 1 root root 7 2010-11-03 22:42 nvidia_dadijiag -> ../dm-0
[code]....
Is my mirror still in effect, or did i just mount one of the specific drives from the mirror?
I am trying to install Ubuntu 10.10 desktop alongside windows 7 on my 2TB Nvidia Raid 0 HDD's but when i select where to install the OS on the ubuntu installation it sees through the raid and only shows the HDD's and no partitions. is there any way to install ubuntu without having to take off Raid?
View 9 Replies View Relatedon my pc, that was running WinXP, I thought of installing Ubuntu. (I did install linux already a few times in the past years and use it on another couple of pcs) But something went wrong. This machine has 2 x 200MB maxtor drives, in raid 0 configuration, supported by the motherboard Nvidia chipset, and working well in Windows. When ran the live Ubuntu 10.04 cd, gparted was not able to access the drives in raid configuration, until I installed the mdadm and kpartx packages then the existing data became visible. So after that initial moment I thought all was ok and proceeded to install Lucid on the machine, dual booting with Windows. I did partition manually so that in my 400GB raid drive there is an 80GB NTFS partition with WinXP, a 90GB extended partition for Linux Ext4 and Swap and then a last NTFS 200GB partition for data. All went well, but now on restarting the computer nothing happens, nothing loads, Grub is not showing, and it looks like I cannot launch Linux nor Windows. All the data from WinXP and the Ubuntu installation seems to be on the disks but the pc is just not booting. I suppose the problem is with the raid configuration that is not handled properly during the installation, but is there anything that I can do now, apart from reinstalling Windows Xp or installing Ubuntu in a non raid configuration?
View 9 Replies View RelatedNew to linux in general and am having issues on setting up a Raid 1 array for two disks on an HP Proliant Microserver which I am looking to be accessible from my windows PC. I have installed the latest version of debian succesfully on a 250GB disk that came with the server. I have added 2 2TB disks which I would like to have in a RAID 1 array and to have visible from windows to store music/videos etc on. I have managed to partition the two disks to FAT32 (which I think is best) and have managed to configure the array so that it shows as active when I use cat /proc/mdstat. I have been following the steps in this article [URl]... squeeze-p2 and trying to adapt it to my situation.
I am stuck on the step to create the file systems using the mkfs command. I try mkfs.vfat /dev/md0 and it comes up with the error mkfs.vfat: command not found. I have tried mkfs -t vfat /dev/md0 and it give the error "mkfs.vfat: No such file or directory" So my question is how can I continue with the process of setting up the array? Or maybe I should be asking is it possible to set up an array with FAT32 formatted disks?
I have a Dell Windows7 PC configured with BIOS RAID1. I want to install SLES10 and configure it with Software RAID1. My question is: Do I need to reconfigure the BIOS RAID setting and if so What should it be.
View 5 Replies View RelatedI need to set up a RAID 1 array on Squeeze. I have 3 partitions: sda1 is root, sda5 is home, and sda6 is swap. (sda2 is the extended partition containing home and swap. This was a clean installation, so I don't know what happened to sda3 and sda4...)
All the information that I've been able to find recommends doing something like this:
mdadm --create --verbose /dev/md0 --level=mirror --raid-devices=2 /dev/sdb1 /dev/sdc1
Do I need to type a separate command for each partition, or is there a better way to do it? Also, should I use the UUID instead of the dev names?
I am currently with Wubi 10.04 under Vista and my Dell XPS 630i has a 1 TB Nvidia RAID controller.First image (Option A) suggests /dev/sda as device for boot loader installation, while second image (Option B) suggests /dev/mapper/nvidia_bcidhdja.I think that the way of keeping the RAID would be using Option B as the device for boot loader installation. Would Option A break the RAID instead?
View 1 Replies View RelatedI changed something in the BIOS which causes a kernel panic, if my card is installed (Ultra ATA/133 PCI-to-ATA Host Controller). I had it working fine til a month ago, when I installed some Linux on a HD on that card. That booted fine too, and I did some disk switching. Still all was well, but yesterday I tried to boot XP (2nd IDE master)(GRUB is Ubuntu/2nd IDE slave), and XP wouldn't load. I clicked here, and clicked there, and now XP and Ubuntu boot, ONLY if the RAIDbus card is Out. Put the card in, and I get a kernel panic/lockup. This HAS to be a BIOS function - nothing is different on the disks, including GRUB menu.
View 1 Replies View RelatedI had Ubuntu 8.04 installed on server#1 and moved it to server#2. Everything works fine, including the changing of eth2/3 back to eth0/1. I was wondering if it's possible to use the nvidia onboard raid and make a raid 1 with this OS not getting wiped out. It's a bios level cheesy raid and it warns that it's erasing the data (which is didn't erase), but wont boot anyway. I'm assuming it's probably best to just create a software raid in the working OS with a fresh 2nd drive.
View 2 Replies View Relatedhow to setup RAID on a Compaq Proliant DL580 G1 Server. Currently there is no OS installed. I used the SmartStart CD but there is no option to setup RAID. When I put in the boot CD for CentOS 5 it recognizes individual hard drives not a RAID Setup.
View 4 Replies View RelatedI'm having some (well, a lot actually) of problems trying to get OpenSUSE 11.2 installed on my home PC. I am attempting to set up a dual boot configuration with Windows 7 installed on an bios Nvidia RAID 0.I was able to shrink the partition in Windows, and rebooted onto the net install for OpenSUSE (the MD5 validated DVD install failed multiple burns with "Repository not found"). I get into the graphical installer portion with no problems off the net install CD. However, the installer is not recognizing that there is an existing RAID 0. It lists the 2 SATA disks in the RAID separately. I can click on SDA1, and both SDB and SDB1 and it shows the disks, but does not recognize any existing partitions. If I click on SDA I get an immediate segfault in YaST and drop back to the text mode installer menu. It is loading the nv_sata module just fine.
From forum searches and google it seems that this is not usually a problem. My motherboard is a Gigabyte GA-M57SLI-S4 with the Nvidia Nforce 570 chipset running an AMD X2 64 3800+. Removing the stripeset and redoing it as Linux software RAID is not an option, I do not have enough space for a total backup/restore. Anything I do has to be nondestructive to the existing Windows installation.I really want to have a linux installation but between the DVD installer failing and now this issue I am about ready to give up on it.
migrate an installed Ubuntu system from a software raid to a hardware raid on the same machine? how would you go about doing so?
View 1 Replies View RelatedI am new to Ubuntu (Karmic with GNOME). I have a Samsung LED UEB7020, with an Asrock ION 330 BD player feeding to a Onkyo TXSR607, AV rec. The other day I downloaded NVidia v180.25, which was very useful, because it immediately solved an earlier teething problem of no sound. However immediately upon re-booting and ever since, the screen size is too big for the TV, meaning that I can not see the top, bottom, side and left of the display by about 2 inches either way. I have checked the NVidia resolution settings and they are correct for the TV, ie 1920 by 1080.
My etc/X11/ xorg.conf file reads as follows:
Section "Screen"
Identifier "Default Screen"
DefaultDepth 24
EndSection
Section "Module"
Load "glx"
EndSection
Section "Device"
Identifier "Default Device"
Driver "nvidia"
Option "NoLogo" "True"
EndSection
I have what I think is a pretty eay question. I'm trying to set the screen resolution of my new 10.10 installation to 1920x1080. The monitor only supports up to 1024x768, but i would like more area. I've done this before but I forgot how i did it. In the end the screen spilled off to the sides and when I ran my cursor over to that section it would disply it. I have a feeling that i need to edit my xorg.conf file, but my nvidia drive has some new mode types and i figured I'd ask before making random changes.
below is my xorg.conf file.
UTC 2010
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
Option "Xinerama" "0"
EndSection
[Code]...
I need to set my resolution to 1280x1024. Problem is, that the NVIDIA X Server Settings does not display such a resolution and I want to use that! My monitor is an LCD capable of upto 1280x1024 75HZ resolution. I'm using Ubuntu 10.10. I did the xrandr command to check what resolutions are available and its output was:
Failed to get size of gamma for output default
Screen 0: minimum 320 x 240, current 1024 x 768, maximum 1024 x 768
default connected 1024x768+0+0 0mm x 0mm
1024x768 50.0 60.0*
800x600 51.0 52.0 53.0
680x384 54.0 55.0
640x480 56.0
512x384 57.0
400x300 58.0
320x240 59.0
In NVIDIA X Server Settings, the list of available resolutions are:
(all of the above)
1152x864
1360x768
I have NVIDIA GeForce 9500GT.
Could any RAID gurus kindly assist me on the following RAID-5 issue?I have an mdadm-created RAID5 array consisting of 4 discs. One of the discs was dropping out, so I decided to replace it. Somehow, this went terribly wrong and I succeeded in marking two of the drives as faulty, and the re-adding them as spare.
Now the array is (logically) no longer able to start:
mdadm: Not enough devices to start the array.Degraded and can't create RAID ,auto stop RAID [md1]
I was able to examine the disks though:
Code:
root@127.0.0.1:/etc# mdadm --examine /dev/sdb2
/dev/sdb2:
Magic : a92b4efc
Version : 00.90.00
code....
Code:
mdadm --create --assume-clean --level=5 --raid-devices=4 /dev/sda2 /dev/sdb2 /dev/sdc2 /dev/sdd2
As I don't want to ruin the maybe small chance I have left to rescue my data, I would like to hear the input of this wise community.
Ubuntu 10.04, nVidia GeForce 9400, driver ver 195.36.15.When I log in, the system always comes up in 800x600 mode. I went into the NVIDIA X Server Settings page and changed it to my preferred setting of 1152x864. I hit Apply, then Save to X Configuration File (with correct root password).All is well until restarting. Then it reverts back. The update doesn't stick. How can I make this the permenant setting?
View 3 Replies View RelatedJust installed Ubuntu, have no idea what I'm doing. This message appears and don't know how to do it. "You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server."
View 2 Replies View RelatedhHey i recently installed Debian Squeeze 64bit over my Ubuntu & Windows, i got everything installed and running including all programs i need without a single problem The one thing i havent been able to do yet is install the Nvidia Driver for Geforce 8800gt, ive searched a few sites but one site is telling you to do this way and the the is telling you to do it another way then people are saying about having errors when xorg updates and stuff.
So i was wanting to know whats the easiest and best way to install the Nvidia Driver package (from nvidia website) onto Squeeze 64bit, i've done it on lenny but cant remember ow
If i get this working then il probaly use Debian as my main OS from now on.
