I am using Opensuse 11.3 In windows, I can create a new network connection , choose broadband network,create and copy onto desktop, so that I can dial up to my internet service provider. In linux, how to do that?
View 1 RepliesHow to create a Dial Up internet connection in CentOS 5.3. Im using a USB modem
View 1 Replies View Relatedi want to use internet on red hat linux through dial up connection. presently i am using internet using my cell phone as modem through blue-tooth.But i want to use internet on red hat through my cell phone. is it possible?i am using nokia 2630 handset.my bluetooth dongle is not supporting linux.please tell me from where i can get a bluetoothe dongle that support linux?
View 14 Replies View RelatedI'm using Linux Mandrake 9.0 on my Dell 750MHz laptop. Linux is not making a dial-up connection, but modem test showed passed. Is there any utility to fix this problem. I have to often use dial-up connection.
View 1 Replies View RelatedI want to configure Internet connection in my linux os but don't know how to do it. In Windows XP the method is quite simple but in linux I know know what to do about, It has been very challenging for me to do it but don't knw how ot do it.This file I have to type at run "RASPPPOE.inf" to get list of available Internet providers.
In windows I do it in this way-
1.First go to My network places ->View network connection->Local area network->Properties->Internet Protocol (TCP/IP)->Install->protocol->Microsoft TCP/IP version 6(select)->Have disk->(then browse to get RASPPPOE.inf file from PPPOE folder)->click OK->select PPP over Ethernet protocol->Click OK->>continue anyway(two times if asked)-> Apply->OK.
2.Then got to run ->Type raspppoe (Enter)->one window will open->select the LAN card (where internet cable is connected)->Click on Query available services->Select Internet provider name and->Click on Create dial up connection.-> Then dial up will be created on Desktop where I enter my username and password to start internet.
I've installed it and all went fine, now i want to set up a dial up connection witch i dont know how. I've tried going to system/adminstritive/networking but 'networking' isnt there.then i tyr gnome ppp but it says it cant detect a modem.
View 9 Replies View Relatedwell after spending most of the morning getting help with my internet connection hanging when I dial up we discover that SELinux is causing it so when I set it to passive I can connect so how can I get it to allow me to connect while being set to enforcing?
View 5 Replies View RelatedI want to configure a Gprs dial up connection through my Nokia N91 to surf internet in openSUSE. I am using openSUSE 11.2 installed as a guest OS in ORACLE VIRTUALBOX (virtual pc) in windows host. I connected my mobile to openSUSE using a data cable and the phone modem is detected. I configured Wvdial.conf file and used Wvdial to connect to the internet. After performing many changes I finally managed to get a successful connection, when still I cannot surf any webpage in the browser.
The only error that I get during wvdial connection is about Namespace (DNS) failed. I am using a AIRTEL (India) gprs internet connection.
i connect to the internet on my laptop using a usb modem. i want to share this connection with other computers. connected through lan cable. i want to manually assign ip on all computers. what should i do
View 3 Replies View RelatedI am using Ubuntu 9.10 . And Using BSNL broadband I want to know that how to create new connection using username and password as we do it in windows.I have used pppconfig command but it gives me error that no dialer found d tell me how to create dialer in Ubuntu 9.10
View 9 Replies View RelatedI'm using fedora core-8. I need to setup dialup server to accept dial up connection.Dial up server shoudl also allocate ip address to client (trying to connect using modem)If some one knows how to do this, please let me know.I'm trying to achieve peer to peer communication between two computers connected using modem on both side over PSTN line.
View 2 Replies View RelatedI use an atom based processor of 1.60 ghz on intel d945gclf board. My ram is a zion 1gb @ 533mhz. Hdd is from western digital 80gb @ 7200 rpm. I have a broadband(dsl) connection from bsnl dataone (a state owned telecom service provider). I connect to internet via a huawei wa1003a ethernet/usb/wireless modem which is provided by my service provider. I need a username and a password everytime i connect to internet via dial-up.
I was using windows xp service pack ii. It was nice and easy installing my modem on xp either via usb or ethernet. Both ways it was easy as i have both the drivers with me.Only and main problem was fighting viruses. I tried many free downloadable anti-virus software to protect my maching. Initially they were fine. But after few months they stopped taking regular updates and became non-functional. I also tried symantec corporate v.10. But it has its drawbacks also. It made my machine perform like a snail.I had previously heard about linux based operating systems. But never tried one. As i am an ameteur in using computers windows xp was suiting my needs. Recently i saw an article in the newspaper about ubuntu which is a free open source operating system. And most important to me it is virus free.But here is a problem also. I cannot connect to internet. My ubuntu 9.10 karmic koala is not identifying my modem and a network between my modem and my machine cannot be established. Also i cannot create a dial-up option where i can give username and password.
Are there detailed instructions for Suse 11.2, anywhere, on installing a hardware dial-up modem and configuring it to get an Internet connection?
View 2 Replies View Relatedhow to create wireless connection in Ubuntu9.1??can u please guide...
View 2 Replies View RelatedMachine A is located behind client firewall. The machine runs telnetd. This is Linux machine with Python 2.5.4 installed. I do not know the IP addy of the router and firewall is not open incoming. outgoing firewall is open.
Machine B (Windows machine) is a server with well known IP address. I can install any programs I want on either machine.
The idea is that I want Machine A to open a socket to machine B. Then I want to hold that socket and use to run a telnet session from Machine B to Machine A telnetd server.
i want to create the wireless pppoe wireless network but it just dont show any help for pppoe connections.i tried with network manager but it works only for eth0 (not for ethl)
View 3 Replies View RelatedAfter >15-yrs using MSWindows, I'm getting a new PC with Ubuntu as my OS. This is for typical home use--net access, web browsing+email, office suite apps.
[code]....
I've read and bookmarked various info on configuring modem, including PPP and wvdial info. But one question: Is there a particular version # of Ubuntu best for external dial-up modem use? I have the CD for 9.10 Desktop edition. It seems that different Ubuntu versions include some things, others not. Another Q: Reading this page about wvdial, it refers only to serial modems. Does the info apply to USB modems, like the USRobotics 5637? [URL]
i am having trouble connecting to the broadband connection which needs to dial the username and password but as i am very new in the linux how can i connect to the internet. i use ubantu 10.04. is there any application to dial username and password and connect to internet?
View 3 Replies View RelatedI have a desktop computer running Debian Lenny, a 56 K modem, and a dial-up account, currently configured like this: computer -> modem -> UPS -> phone jack
When I run off a Knoppix live CD, I can use kppp to configure pppd (using PAP/CHAP authentication and hardware control flow) to dialup and surf. When I try to user kppp to configure pppd exactly the same way on my hard drive installation, I get nothing. Both my Knoppix live CD and Debian Lenny use exactly the same version of kppp, but the pppd related files in /etc/ppp look a bit different.
Under both Knoppix and Debian Lenny hard drive installation, when I try to connect, the login debug window of kppp shows:
Code:
ATZ
OK
ATM1L1
OK
ATDT [phone number]
At this point I hear the modem dialing out, and when using Knoppix, after a few seconds I see
Code:
Which I think corresponds to my route to the InterNet being established through my ISP. When using the hard drive install, I never see the CONNECT, and all indications are that my modem is not sending authentication information at all, but getting stuck right after dialing out, so that my ISP gets a phone call from a modem which... refuses to speak. I never had any problems before, so I am baffled.
So apparently my system is currently misconfigured in some way which prevents point to point protocol from getting out.
Questions:
I have a firewall on my computer which I set up using guarddog. I have enabled point to point protocol from internet zone to local zone. I know that ppp is a symmetrical protocol, but my understanding is that I do not need to enable point to point from local to internet zone. I have not enabled irc protocol because my understanding is that this is only relevant to software flow control using chat scripts. Does this sound correct? Is there some additional protocol I need to allow in order to use pppd to dial out?
When I reboot my computer (off the hard drive) I sometimes see that the system complaining about a failure to stop every process, and sometimes I see mention of an eth0.pid. I have been looking for lock files; would they all be in /var/run?
When I use kppp to configure pppd, I want to do that as my ordinary user for at least two reasons, correct? don't want to run pppd as root user for security reasons kppp is a GUI and root user can't use X (on Debian)
So I should see in home directory of my ordinary user
.kde/share/config/kppprc
.kde/share/apps/kppp
But not in /root directory, correct? What pppd related processes should I see with ps -ef if everything is working?
For any distro, via CLI and configuring config files, without using graphical tools. Or there have to be different?
View 1 Replies View RelatedI have decided to install Debian 8.2 in my desktop. I am test driving it in virtual box find and solve any problem I may face later on. The isp I use provides me with a shared ip every time and I have to create a DSL connection with username and password to connect to it. I can create the connection from the gui connection manager using "nm-connection-editor" command in Debian.
I am using elementary os freya and I can do so from the system tray at the top right. So, I wanted to do the same in debian also. But I can only create VLAN, VPN, Bridge, Team and Bond. There is no option for DSL but if I create one in the way mentioned before, it appears as a profile under "Wired" network option in system tray. I read some post regarding network option in system tray but I could not make them work and other I did not understand. In KDE window manager I have this feature but I want to use gnome 3.
Alright, I was playing with the VPN capabilities in KDE4 on Squeeze AMD64 on my personal laptop (see my signature) and found it very easy to create a VPN connection and connect, but that's it. I made a VPN tunnel to one of my client locations as a test, but could use rdesktop to get into the server. Then I realized I couldn't ping the server either. I also lost all ability to browse the web and everything while the VPN was up. Upon checking ifconfig as root, I saw that it created "ppp0" and hat it had pulled an IP from the client network, but all of my networking capabilities were gone. What gives? What is it that I am missing?
View 4 Replies View RelatedI have just installed FC11 from a DVD I created from an ISO.I also have FC10 (using here) and Windoze XP pro all on separate HDDs.I have not been able to configure my internet connection, when I try to create a new xDSL connection I get an error message; package needed 'rp-pppoe'.I don't now how to get the package without a connection.I have tried with and without Network Manager.
View 2 Replies View RelatedI tried to build a PPP connection with umtsmon, but failed. I'm using a ZTE MF110 Stick. The reaction from my provider's support was succinct: "Linux untersttzen wir nicht." (We don't support Linux.)
The hardware seems to work fine, the stick shows a green light, and I sent a test SMS via umtsmon. The umtsmon interface successfully identifies my Provider, but does not connect.
Here is part of umtsmon debug output:
Code:
UIState::setState(6 -> 6)
##P4 t=133: ConnectionInfo:InhibitionCount ++, now is 1
##P3 t=133: TempSerialPort::TempSerialPort()
##P5 t=133: 0x75a6c0 = Query::setSerial(0x7fffece12a00)
##P3 t=134: Serial::openDev('/dev/ttyUSB2') as FD 8 - Serial instance
[Code].....
I just removed ubuntu-desktop in favor of kubuntu-desktop. Now I can't create an ad-hoc wifi connection however hard I tried from network-manager. It simply is not visible to other PCs. And when some connection is created on another ubuntu PC, I can't connect to it.. I switched NM off and tried the CLI way.
[Code]
Under DSL tab in network connection we can create DSL connections, but they only allow wired connections(eth0). I need to connect using wireless connection(wlan0). I migrated to Ubuntu recently. With windows I was able to connect with wireless connection. I'm sure there is a way to achieve this in Ubuntu as well.
I'm using Ubuntu 10.10 (using since 9.10)
What I want to do is to share the internet connected to a computer with a telephone, over another telephone which is permanently connected to the pc.The thing is, that some guys found a way of making this on windows, in fact, I already set it up on xp and works like a charm, it involves configuring in a certain way the telephone, and to use 2 programs. One is CCProxy, which redirects the internet connection to the telephone, and another one, which updates the IP adress of the telephone connection to dyndns, so that I can put that adress on my second telephone as proxy, and this way, surf on the net through my home internet on the telephone anywhere. Tricky right?
Now, the thing is I don't like at all booting windows only for sharing internet with my telephone. So I want to do it in linux. I use Ubuntu and Puppy linux home.I tried setting up the connection to the modem with wvdial, and... I got connected! But hey, when I connect to the telephone, I lost my internet connection (main, cable based, the pc connection) :-S. I mean, somehow, the "active" connection for the browsers and all the internet programs is now the connection I have made with my telephone, which is plugged to the computer.Now my objective here is that NO CHANGE of active connections get done when I start the connection to the phone, and then, get a program like CCProxy, and a dyndns updater for sharing the internet connection on the pc, to the connection made on the telephone-modem wired to the computer.
I would like to make a script which can check my ISP connection, I have a dynamic IP and it seems that lately it often gets changed.
So I thought of making a script which does a NSlookup and send this to my root address. But it would be better if it only does this when it notice a disconnect otherwise I get loads of messages. I use a watchguard firewall and behind this I have my Ubuntu server which is also the DNS and DHCP server for my internal LAN. My watchguard makes a DSL connection with my bridged DSL modem. Also the watchguard has a logging system and I send the syslog to my ubuntu server but it's too much work to look everyday into this whole logfile system.Or would it be better to look into this logging files and search for a specific description and send only this to my root mail?
I have just taken on a dedicated server sitting somewhere in Norfolk. I have created a website that uses PHP to connect to another remote server in order to interrogate a MSSQL database. This script, running on Apache, uses a VPN connection to connect to the remote server.To test, I have Apache on my laptop at home and just used Microsoft Network Connection to create the VPN connection.I have now uploaded this site to my new CentOS server and need to create the same VPN connection. I understand this is a command level and have been advised to use OpenVPN which I have successfully installed.My problem is I only have the details remote ip address, username and password. I believe I have to use the 'client.conf' script instead of server.conf.
View 1 Replies View RelatedI am running Fedora 13 Gnome. When I try to create a VPN connection using Network Manager (vpnc) it says that it cannot save the connection and exits out. I can provide other information if necessary.
View 3 Replies View Related