After I managed to crash my Debian on a version upgrade and failed to reinstall it by the netinstall CD I decided to switch to Ubuntu on my (old) fileserver. Unfortunately some of the disks can not be mounted:
[Code]...
I am currently working on fedora 12.I Tried to install Fedora 13 on my System but dont know why Installation being stopped while looking for basic storage devices .how to come out from the problem?
View 1 Replies View RelatedI am just getting started with Ubuntu and love it so far. It has breathed new life into an old Compaq Presario V2000 and once I get up to speed on it I hope to start running it on all the rest of our machines.
The only major problem I am having is that none of the USB devices I have plugged in are being detected. From what I have seen online I should be getting a notification and should be able to view the devices at Places/Computer but so far, nothing. Googling this problem it appears that individual devices often don't work but I could not find anything on all USB devices not working.
Any ideas as to what I am doing wrong here?
Upgraded from 9.04 to 9.10, touchpad on my laptop stopped working, but i had my USB mouse so I upgraded to 10.4. After the reboot, both the USBMouse and touchpad no longer work, rendering my Ubuntu Installation a useless. Luckly I have OpenSuse installed on this laptop as well. I have a Gateway MP6954
View 1 Replies View RelatedWhen a USB device is attached to the laptop 10.04 does not automount the device. i.e. the device, be at an external drive, memory stick or iPod does not display with the correct icon on the desktop.
However, if one looks under Places|Computer there they all are with the correct icons. The devices can then be mounted from there.
This issue seems to be related to these other posts: [URL]
This is really disappointing given that 10.04 was promoted on its iPod friendliness!
System: IBM Thinkpad T41; Pentium-M 1.6GHz; 1Gb RAM
After upgrading to Lucid 10.4, I find that after booting I can no-longer auto-mount any USB drive when they are plugged in. They simply doesn't appear on the desktop as they did. Swap my PATA drive back to the one with 9.10 still installed on it is well.However, if I have USB drives plugged in before boot, they appears on the desktop, but are not auto-mounted as previously. Also when I click on any drive icon for the first time there is no response. Try again (on any drive) an the devices will all auto-mount revealing their contents in the window that subsequently opens. Everything them seems fine. I can unmount and remount at my leisure with any number of devices.
I do not have the problem of root only access that others have mentioned. I have played with usbmount and pmount as others have suggested, to no avail. They have both been removed.I have the HAL installed as default, and have already ecked media_automount_open for Nautilus on the gconf-editor.Disabling the floppy in the BIOS has not effect and I do not use autologin option.With (say) two USB drives attached, whether the devices are recognised at boot or not after boot,lsusb reveals:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[code]...
I have Virtualbox installed from the Ubuntu repository. As I just found out, I can't access any USB connected devices (printer, scanner). It seems I can get these USB peripherals to work by using a different Virtualbox repository. how to do this without loosing the OS installation that I have already setup in Virtualbox?
View 6 Replies View RelatedI had XP before, which gave me an error message and crashed. I didn't have the XP CD so I decided to give Linux an error. By what i can find, I have a somewhat unique problem. My USB drives no longer work. They light up green, so they obviously have some power and so on, but there is no response from any devices that you plug in, i.e. mouse, flash drives, etc. Nothing works.
View 1 Replies View RelatedOther o/s because I plan to turn that machine into a Xen server.
Unfortunately I don't have much exper building computers/ hardware. What I'm wondering is whether the number of devices (like hard drives and optical drives, etc) is a function of what the mobo can support; or, if the bays are there and the cable has enough plugs I can just go for it.Specifically I'm trying to have 3 disks and one optical drive. The machine happens to have been a media center version desktop so it has this like 9 in 1 card reader thing in it but I don't think it uses that flat cable for data transfer anyhow. It looks to be connected differently.
i installed ubuntu today by installing Wubi and after downloading i rebooted computer and selected ubuntu but i got an error saying 'Try (hd0,0): FAT16: NO WUBILDR' and there was few more but i forgot and at the end it says 'Cannot find GRLDR in all device Press CTRL+ALT+DELETE to restart' it used to work when i had vista.
View 3 Replies View RelatedI recently bougt an Asus N61DA with Windows 7. I decided to install Ubuntu alongside Windows, so I made the Ubuntu CD, just like it said. Then I inserted the CD and restarted the computer. I started the installer (ubuntu 10.10 64-bit) and chose the option where it says "install ubuntu alongside other operating systems", or something like that. So, the installation started, but then I lost the internet connection, and the installation stopped.I re-connected the computer, but the installation still wouldn't continue. I restarted the computer and then nothing happened. I've restarted it several times, but still nothing happens. I've inserted the Windows recovery CD, but it doesn't work
View 9 Replies View RelatedRecently I installed Fedora 12 without any hassles except that the USB devices are not getting detected. I checked with /proc/interrupts and the ehci_hcd module doesn't get any interrupts. Here is my dmesg (done to show only USB related messages) :
Code:
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
[code]....
I'm using a Dell SC440 server for this effort. I started with Debian 6.0.7 32 bit i386 version in mid April and everything seemed to go smoothly until the first boot finished, I wanted to look at the hard drive just to see what storage space was left to work with. The drive was not recognized and I could not mount it. The error message was "One or More Block Devices are Holding /dev/dm-0".
I could not find anything on the debian forums that seemed to relate to the error message so Google led me to the same problem on Fedora, Ubuntu and one other distro. I flattened the machine and restarted from scratch. This time using Debian 6.0.7 AMD64 version. The install went well but I had the same problem with the same results. So I started over several more times before the new Debian 7.0 AMD64 version was released. Under Debian 7.0 I not only get the same error message but I also get a message that my video card is not supported under this new version of gnome and sudo does not work.
I've been struggling a bit with install F11. F10 installs without issue. I have two internal SATA drives, a PATA DVD-ROM and a USB drive. The BIOS recognizes everything. However, when I got to the disk partition utility, Anaconda could never detect one of the SATA devices. I tried swapping cables, ports, etc. No luck. Today, I ran across this Bug thread: [URL] I checked the screens Ctrl-Alt-F1-6. Nothing obvious. But, for fun (from the bug thread) I went to the prompt on 2 and ran:
dmraid -r -E It found an "nvidia" RAID "thingy". Forgive my ignorance on what it really is called or what it does. Anyway, I answered yes to erase the "thingy" and voila. I was able to install F11. Not sure if I made a good title, but I've seen bits and pieces of people having similar problems with F11. And BTW, the drive that had "nvidia" on it was from a machine that was using nvidia hardware RAID 0 - but F10 had no problems with it.
I've been running F10 with a four disk RAID5 setup that has been working fine, however when I tried to do a fresh install of F11 I can't get past the "Select Country" and "Select Keyboard" screen of the GUI as a message will say "Detecting Storage Devices" and then throw up an error. I can't give you the full error, because when I click Save The Detecting Storage Devices box appears and I can not select anything under it or enter my Bugzilla account.However, when I plug just the hard drive that has XP on it then the installer continues swimmingly.I've backed up everything, so if I have to I could zero out the drives however they're all rather large so it'd take an inordinate amount of time.
View 2 Replies View Relatedi have a vaio, with a nvidia geforce 330m. i upgraded from 10.4 to 10.10, using the same driver i had before (256.44, form the nvidia web site) and following the same instructions i found useful the previous time [URL]. my problem: now my login has no graphic interface: i am displayed this error:
Quote: thermal reporting for required devices not enabled, aborting.
and i can log in and use ubuntu only by command line interface, i tried also to make a clean install using a live cd, but nothing changes. have i to go back and use 10.4?
I'm working on a server and noticed that the to RAID5 setup is showing 4 Raid devices but only 3 Total devices. It's on a fully updated CentOS 5 system that only has three SATA drives, as it can not hold anymore. I've done some researching but am unable to remove the fourth device, which is listed as removed. The full output of `mdadm -D /dev/md2` can be see below. I've never run into this situation before.Anyone have any pointers on how I can reduced the Raid Devices from 4 to 3? I have tried
mdadm /dev/md2 -r failed
mdadm /dev/md2 -r detached
but neither work and since there is no block device listed I'm not quite sure how to get things back in sync so it's only seeing the three drives.
/dev/md2:
Version : 0.90
Creation Time : Tue May 25 11:07:04 2010
Raid Level : raid5
[code]....
While installing Fedora 12, no devices were found on which to create file system (see attch.). I get the same message either on Live CD or DVD boot start. It looks like Fedora do not see my hdd. But Palimpsest can see my hard drive (see attch.)
Hdd is on my NForce 4 Ultra m/board and connected via "sata". Also I have raid controller on my board. But it is not in use: I turned it off in bios.
I'm installing F12 on a new HP ML-350 G6. The machine has 4 Gb memory, and a Smart Array P410i SAS controller. There are two 72 Gb disks set up as a RAID 1. I'm using a full install DVD. There are no other storage devices other than the RAID, a USB tape drive, and the DVD drive. When I try to install F12 it hangs after setting the keyboard type with "Finding Storage Devices". I've let it sit for an hour or more and it doesn't get beyond that.
F11 installs on the machine with no problem. I've used the F12 DVD on other machines with no problem (but not any other ML-350s). If I switch to a console session, dmesg shows the driver for the controller (HP CISS) has loaded and the RAID drive recognized. The appropriate devices (/dev/cciss/c0d0, /dev/ccss/c0d0p0, etc.) are all present in /dev.
As stated running f13_64 and trying to run preupgrade to 14 fails in anaconda after reboot.
Just hangs at "examining devices". I've looked online and theres several bug issued for this nothing really ever seems to be fixed.
Is this just broke? The preupgrade?
I cant go to f15 as it will not run on my machine at all. Never quite loads gnome proper.
Pretty standard p35 board /core duo. One drive with a /boot /LVM setup straight from the f13 installer.
How to locate usb devices before the process of installation?
View 2 Replies View Related"Computer" nor "Palimpest Disk Utility" showed anything about the attached devices. However, the command:
Code:
lsusb
outputs:
Code:
Bus 002 Device 004: ID 05a4:9866 Ortek Technology, Inc.
Bus 002 Device 003: ID 04d9:1203 Holtek Semiconductor, Inc. MC Industries Keyboard
Bus 002 Device 002: ID 047d:1029 Kensington Mouse*in*a*Box Optical Elite
[code].....
Right now I'm running ubuntu with three partitions. /, /home and a swap partition. If I did a clean re-installation what exactly would be lost afterwards? /home obviously not but what about all the system settings, visual individualization or downloaded software from the ubuntu software center for example. Furthermore, I'd like to know why a clean re-installation is regarded better than an upgrade.
View 4 Replies View RelatedI installed Fedora 12 and performed the normal updates. Now I can't reboot and get the following console error message.
ERROR: via: wrong # of devices in RAID set "via_cbcff jdief" [1/2] on /dev/sda
ERROR: removing inconsistent RAID set "via_cbcff jdief"
ERROR: no RAID set found
No root device found
Boot has failed, sleeping forever.
Getting very frustrated trying to install F12 to my work PC. Its a dell precision 670 with a 3ware 9550sxu raid controller running raid 5. Its consistently crashing at the point when it says 'finding storage devices' with a message about : Mismatched Sizes. What I could try? I had no problem on this machine with fedora 11, so whats changed? Just for info by the way, theres two raid volumes on this system a 750Gb that contains my windows vista installation in a 500 Gb partition (NTFS) and the free space I'm using for fedora. The second volume is a 2TB data volume with a single data partition (NTFS).
View 1 Replies View RelatedThere seems to be no documentation on how to automount partitions and USB devices under systemd in Jessie. (Overall, systemd entirely lacks any useful documentation or GUI configuration tools -- all very cryptic and hidden.)
I created custom files to enable automounting. I put them in /etc/systemd/system -- this may not be the right place, but it works.
Kernel note:
This does not work under the old Wheezy kernel linux-image-3.2.0-4.
To automount my Windows partition so I can access its files, I created:
/etc/systemd/system/media-windows.mount
The name of the file must match the mount point -- in this case, /media/windows
My file notes the device and file type, plus an fmask option so all the Windows files don't seem to be executable:
[Unit]
Description = windows mount to /media/windows
[Mount]
What=/dev/sda1
Where=/media/windows
Type=ntfs-3g
Options=fmask=111
[Install]
WantedBy=multi-user.target
The file ownership must be root.root. Apparently it doesn't need to be executable.
After creating, enable with:
sudo systemctl enable media-windows.mount
and it will mount on the next boot.
I read elsewhere that the before running the enable command you should run a start command:
sudo systemctl start media-windows.mount
but that didn't work for me.
Installing stretch stops at detecting network devices. This is an attempt to install stretch over the top of Windows 10 on a Toshiba Radius 15 with 2 each USB2 ports and 2 each USB3 ports, and no RJ-45. Its wireless is based upon the Intel 7265. Just before the presentation of the wireless list, the system reports the need to install non-free:
iwlwifi-7265D-9
iwlwifi-7265D-10
iwlwifi-7265D-11
iwlwifi-7265D-12
and asks for media. Whether I respond yes or no, the driver selection screen comes up. [I have not been able to find those four specific files on the Internet.The network card screen comes up, I select the Intel recommended firmware iwlsifi, but the page just recreates itself and waits for a new selection. If I select either 'none' or 'not listed', the installation fails saying there is no network card.I have obtained from Intel their suggestion as of Aug 2015: iwlwifi-7265-ucode-25.30.14.0.tgz.I placed this on a USB stick in a subdirectory labeled 'firmware'. This was built from Windows 7 on a FAT32 file system.
There is also a Dynadock docking station that connects to the Toshiba via a USB3 cable. Besides video, USB,and audio, this has an Ethernet port. I have tried this connected to the laptop but it also requires a driver. I have placed that driver on the firmware directory of the USB also.
Are the four files listed above somehow inside the iwlwifi driver tgz?Is there a way to get the docking station drive to load so I can use its Ethernet port?
I have used Rufus to build the stretch USB from Windows. I do have a a Linux box I built with the same USB. I would use it but so far, I only have a command line on it and I have not figured out how to access debian.org to download the installation files nor how to put that on the stick.
Why is it that FC6 installs just fine from a USB CDROM in an external enclosure but FC12 boots from the CD asks to install or upgrade an existing system but then stops at no devices found and wants the install path for the install image? It appears to see the CDROM, boots then looses its mind and forgets a CDROM was attached.
View 13 Replies View RelatedI have a broadcom wireless card in my laptop and as far as I know, it acts as an USB device. I also have one USB stick wireless device (TL-WN422G - uses ath9k_htc driver) which I want to use at the same time as the first (Broadcom) device.
The problem is, after I load ath9k_htc - iwconfig does not show the new USB device (the TL-WN422G - wlan1 / ath0 / whatever), but only the old one (wlan0 - Broadcom, checked by MAC).
I tried this USB device (TL-WN422G) on my other computer that has PCI wireless card in it, and they both worked just fine together after I pluged it in... I get wlan0 (Ralink) and wlan1 (TL-WN422G). Is it some kind of a problem for the laptop that both devices are recognized as USB? How do I make wlan1 appear on my laptop?
also, my system is fully up to date 2.6.35 kernel (Arch)
edit: I've already downloaded the needed ar9271.fw from linuxwireless.org and I put it into /lib/firmware - something wrong in that?
dmesg gives me this on laptop:
usb 1-5: new high speed USB device using ehci_hcd and address 9
usb 1-5: ath9k_htc: Firmware - ar9271.fw not found
ath9k_hif_usb: probe of 1-5:1.0 failed with error -22
[Code].....
I'm running wubi on XP machine. Started out originally with 8.04, and gradually upgraded to 10.04. Recently, I was creating linux bootable USB drive, and put it in my system to see if it would work. After booting the LiveOS, and rebooting my machine, I know get the error Cannot find grldr in all devices when booting Ubuntu. I don't know what grldr is, but I assume it is the GRUB Loader.
Did booting the LiveOS screw with my MBR perhaps?
How can I fix this, and if not, is it possible to reinstall wubi, without losing anything of what I have now?