I recently installed F12 on my main notebook and ever since the fan has been running at full speed (or near full speed). According to the 'sensors' command I usually have temperatures between 50-70. I didn't have this problem before the installation.
View 2 Replies
I'm fairly new to fedora. I used Fedora 14 on a virtual machine just to mess around with it a little while back but thats about it. As far as linux goes, I just test a bunch but can never seem to pull myself away from windows. I am hoping this is the time but these issues are the weirdest I've seen on any linux distro ever. My GPU (Radeon 5750) is running at 69C idle and the fan is at full speed. I am not overclocking it at all and I'm using the default drivers that came with fedora. It works just fine in windows and a lot cooler. How can I fix this?
I'm running the Gnome 3 desktop version, which I am also getting some graphics artifacts. In the bottom bar I get a dashed white line that comes up every time I boot and goes away when I make the bar expand. Also in the applications window I get the same dashed line at the top of the window and sometimes the top of the scroll bar. So far I really like Gnome 3 (Idk why everyone is whining about it) and I'd like to stick with Fedora, and linux for that matter
I upgraded from FC12 to FC14 and now the system/case fan blows full speed constantly. I also moved from i386-PAE to am64.
The CPUs are cool, the machine is basically idle, and the fan noise is really annoying (and blowing cool air).
In FC12 the fan would auto-adjust with CPU load. This is not the case now.
I ran sensors-detect and it doesn't seem to find my fans:
[root@pangea modprobe.d]# sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +40.0C (crit = +75.0�C)
k8temp-pci-00c3
Adapter: PCI adapter
code....
I don't remember ever having to even run sensors-detect in FC12. I searched the board for a bit and didn't see any solutions. I'll attach the full output from sensors-detect.
I installed on this laptop two OS : Windows XP SP3 with drivers for M11 from Toshiba download site Fedora 14 64 bits I have no problem running Windows but sometimes when I run Fedora I hear fan starting to run at full speed then computer hangs. When this occurs, I must power off it using switch then reboot and I lost my work. I try to run Memtest86 during a full night and I did not get any error or hang.
Is there somebody who already installed Fedora 14 on Toshiba Tecra M11? kernel is 2.6.35.10-74.fc14.x86_64 and my graphic card worked fine with hardware acceleration out of the box.
[Code]...
I am working on an embedded system, which is an USB MSC device that supports some vendor specific scsi commands. I am using FC10 laptop as USB host for testing, and it runs some small apps based on sg3. All has been well for ~ a week. The FC10 laptop is able to communicate with the device and retrieve data. Suddenly, starting from today, the laptop is not able to properly detect the device. When plugged-in, the MSC device is detected as input device (I thought). This is observed from "dmesg" output and changes in "/dev/input/".The device under development is running at full speed. When I connect to winXP, no problem. A windows file explorer pops up, showing the content of the drive.Also, the FC10 has no problem with other USB flash drive (high speed).
View 1 Replies View Relatedhave a " Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)" NIC.I was unable to set it 1000bit and full duplexThe output lspci -v as below.Quote:
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
Subsystem: ASUSTeK Computer Inc. Device 8432
[code]...
DG31PR Intel Corporation with Lucid 32 bit. how to get the CPU fan to normal speed. I googled a bit around but so far no success.
View 3 Replies View RelatedI can't figure out why but my processor is running at 100% on all four cores, and the fan is running at max speed. All I did was double click an a.out file created by g++, and it is running at full speed now.
[IMG]file:///tmp/moz-screenshot.png[/IMG][IMG]file:///tmp/moz-screenshot-1.png[/IMG]
No error message given and system still works. Same result on Ubuntu, Chrunchbang and Fedora 12. Maximum speed 533 but size is recognised. Tried on another machine all is well.Errant hardware is ASRock N68-S with AMD AthlonX2 5050e. Stated as compatible on the asrock ref.
View 4 Replies View RelatedI have a Compaq 8710w and after upgrading to the latest Debian/testing (Linux version 4.1.0-1-amd64)the fan runs at full speed all the time. There seems to be something strange with the temperatures reported by temp4, it is stuck at 100 degrees.:
Code: Select allroot@...:~# sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +16.0°C (crit = +105.0°C)
temp2: +38.0°C (crit = +105.0°C)
temp3: +22.6°C (crit = +110.0°C)
temp4: +100.0°C (crit = +110.0°C)
temp5: +37.0°C (crit = +110.0°C)
[code]...
I found this related problem: URL... . Note that here the problem is that the fan does not spin and that temp4 reports 0 degrees.
one of my Evga GeForce 9500 GT's fan started acting up today. It is wobbling, vibrating loudly, and not spinning at full speed. And while I believe the card is still under warranty, I'd rather just buy a new fan and put it inmyself avoiding the hassle of sending it back and waiting for a replacement (and most likely refurbished) one. That being said, does anyone know where I could buy just the fan? Google has turned up nothing so far but the numbers on the fan are A4010-45LB-2UN-C1 and FA7C0412MA-SBNNA but I have no idea what these numbers are; the manufacturer is Cooler Master.
View 1 Replies View RelatedI just installed Ubuntu 9.10, replacing Windows 7.
its running a little slower than I hoped it would, loading movies takes a while, and when i switch to full screen, it takes about 5 seconds to catch up.
im suspicious that my video card driver might not be configured correctly. can anyone tell me what I might need to configure to get things running smoother?
other things on the computer are also running slow, like opening Firefox, it takes a while for the window to appear.
- Athlon 64 x2 5200+
- Gigabyte GA-MA78GM-S2h motherboard
- Radeon HD 3650 512mb pci-e
- 4gb DDR2 800
and I do have ATI catalyst installed
I am running Ubuntu 11.04 off of an 8GB flash drive. I have no hard disks but I do have a 3.2 GHz Pentium 4 with Hyperthreading and 1 GB of RAM. So, it shouldn't be my system that is causing it to run slow, but rather limitations of the USB (I'm pretty sure it's USB 2.0). Is there anything I can do, unnecessary processes I can kill, etc. to make it run faster?
View 4 Replies View RelatedMy wireless connection work just fine but it gives me wrong connection status, like 10% even when I'm seating near the wireless router or disconnect status while I steal manege to use the internet at full speed.
View 1 Replies View RelatedWhen the summer-holidays are a fact and it's time for some fun I will be upgrading my home network with a diskstation of some kind, and since all models I currently looks at supports 10/100/1000 M/Bit networking it got me thinking.
My desktop also supports 10/100/1000 M/Bit networking and since I already uses a 10/100 M/Bit switch between my desktop and (file)server, it would be very easy to buy a new switch that also supports 1000 M/Bit networking and then connect the diskstation to that switch as well. But the router the new switch will be connected to is only running 10/100 M/Bit so the question is, at what speed will the new switch be running?
On an old laptop I needed some package (pdftk) from 11.3 and so I upgraded. But I cannot get the graphics running at a reasonable speed now. This old laptop has a Radeon RV350 (mobility Radeon 9600 M10) as shown by lspci. The current ATI closed source drivers don't support this card any more but the legacy driver doesn't support the 2.6.34.7-0.4-default kernel anymore.
Using the open source xf86-video-ati driver gives me an unacceptable alternative:
Without a kernel boot parameter it's dead slow, glxgears shows only 200 frames/sec and my Opengl application (see below) is just unusable with this setting.
Adding the 'nomodeset' kernel parameter make the graphics much faster - glxgears reports 1800 frames/sec - BUT now my Opengl application freezes the machine (only a power cycle can revive it). I'm using the Python/OpenGL application "Impressive" to present pdf files.
I'm installing (X/Lubuntu) on a machine with only 448 mb RAM and a 2GHz processor. I'd definitively prefer Xubuntu, but if it'll be very sluggish I'll go for Lubuntu, because it is important that the machine runs at a decent speed. So which should I go for? Is 448 mb RAM enough for Xubuntu?
View 9 Replies View RelatedI have a requirement where I want to extract the full name of the process running in my box. I tired various options of ps. The wide option gave me the full command but that contains command, the interpreter and also the arguments passed.
Code:
XX XX XX XX XX XX /usr/bin/sh /path/to/exe/myexe.sh arg1 arg2 arg3.
Is there any way from ps or any other command I can extract the full name of the command
Desired Output :
Code:
/path/to/exe/myexe.sh or myexe.sh
I'm running a XFX Nvidia GTS 250 512MB card. I have installed Ubuntu 10.04 and so far I'm loving it - apart from one small issue. Using 195.36.24 drivers, I cannot control the fan speed - it keeps running the card pretty hot - hitting 75 deg. C when one OpenGL game is running. The fan barely goes over 60% speed - I'd rather have it run at 80% constantly to keep the temps under control.
There are drivers on nvidia website which "seem" to be a lot newer : 256.35 (using 64bit Linux) - are those "direct replacement" for the 195.36 which Ubuntu installs by default?
I have a well ventilated case (1x120mm pulling air, 1x120mm pushing out, neat cabling, etc). I have found nvclock but no joy - even with -force it doesn't want to change fan speed.
I often run my ubuntu as SSH server only so i stop GDM when i do that, but i found out that after i stop gnome, my ATI gpu fans spins up like crazy and sounds like a jet plane, (i have ati closed source driver installed) i am worried to leave the fan on like that, so i have to start a X session again. Then the fan slows down I would like to be able to have slow fan speed when i drop to text mode only, one is its light weight, two is for security
View 3 Replies View RelatedI would like to run Linux Mint fullversion from a flashdrive. Is it possible and easy to set up. I have found how to basically create a flashdrive version of the live cd, but I would like to run the full version from the flashdrive.
View 7 Replies View RelatedChecking the process table for the running sendmail, I would like to know the full path to the sendmail binary a la the ps -ef on a Sun or other servers. How do I get ps to give me the actual path, or should I use a different tool on my Linux servers?
View 2 Replies View RelatedI have an XP laptop, currently running very low on HDD space and RAM capacity, waiting to be replaced. Very slow indeed. It recently had problems booting up, and now takes about 20 minutes to get fully started. Is it safe/advisable to run the demo version of Ubuntu from the LiveCD? I really can't afford to trash or crash my computer, it's got lots of important data on it etc.
View 4 Replies View RelatedI have an HP ProLiant DL560 server with Debian 6.0 installed and cannot figure out how to get the fans to run at anything except high. I have searched google and this site, but cannot find anything that works on Debian 6; the SLES packages will install, but don't do anything.
Server Specs:
HP ProLiant DL560
4x Intel Xeon 2.20GHz processors
6GB RAM
2x 72.8GB 15k rpm SCSI HDDs (Raid 1)
2x power supply
I finally bought marble blast gold. a very cool game. i was able to run it on my mac perfectly fine. but now when i install in on my ubuntu machine its not doing what its supposed to. i did a ./MarbleBlastGold 1.4.1.sh.bin after doing the sudo -i command. it installs just fine. but when i go to run the game, i cant find it in the menus. thats ok, i have commend line experience. so i cd to the install folder, and run a ./marbleblastgold, and this is the error i get. so what can i do, and what does this mean? good thing i bought it for all my computers. one copy of course.
View 2 Replies View RelatedUbuntu 64bit. The sound system works and plays noises correctly when I test the speakers in sound preferances. The internet BBCi player(Radio) plays sound correctly. Banshee & Rhythmbox try to play music files at double, or more, speed with no sound output. Spotify Linux version also tries to playback at double speed with no sound output. Media Player attempts to play music files at high speed. Media player plays the Video and audio tracks at high speed. VLC Will play the video at normal speed but with no audio.
View 1 Replies View Relatedi both have the same problem, i'm trying to burn my images at 4 or 8 speed, but ubuntu 10.04 says that the hardware does not support that kind of speed and switch up to 16 speed and more. i know it can burn at low speeds, at least in windows, it is a bit strange that fast burning is okee, and slow not, what can i do to prevent this? i don't wanna burn to much errors on my discs
View 5 Replies View RelatedAfter "yum install emacs" & "yum install emacs-ess", I was able to install emacs on my X86_64 running Fedora 10.
If I run one session of emacs everything works fine.
Once I start a second session and try to resize or move the emacs window, the system stops responding.
I have the following nasty issue:I am using fedora 12 and I use vpn for working remote.When I browse the internet the speed is very slow!even when I do a yum update it downloads the packages with max 100kb. if I drop the vpn connection I download the packages with 1Mbdo you know what the problem could be? i created the vpn connection using the network manager...it is a regular pptp connection for the vpn!
View 14 Replies View RelatedI am running Fedora-13 64 bit on my Dell Laptop, The same Laptop has Windows-7 as well (dual boot system). I have chosen ext3 filesystem while installing fedora. The file transfer speed in Fedora-13 over the network to my network drive comes out to be not more than 5MBPS.Where as in Wndows-7 I am getting the speed of around 10~12 MBPS. Also I found that copying files in USB flash drive is very slow than in Windows-7 . What could be the problem? To add it , I have another Laptop Running Ubuntu-10.04 , which also performs network transfers at 10~12 MBPS. So its just the fedora-13 who has this problem. As far as I remember this was not the case with Fedora-12
View 6 Replies View Related
