Fedora Networking :: Iwconfig And Iwlist - What Frequency A Wireless Interface Is Using
Nov 10, 2010
I have just upgraded my system to Fedora 14. One thing I noticed after running some applications on it is that it is not possible anymore to figure out on what frequency a wireless interface is using. If I set a wireless interface to monitor mode and perform the iwconfig or iwlist command, in the past, I could see the frequency used on the interface, but now, this information is not present anymore. My wireless interfaces are in monitor mode.
Has the frequency information been removed from iwconfig or iwlist commands? If it has, is there another way to report this information?
Here is an output from iwconfig on my system:
View 4 Replies
ADVERTISEMENT
Mar 11, 2010
The adapter I purchased (Zonet ZEW2508 ) uses the Ralink 2070 chipset - a fact that originally excited me because Ralink seems to be fairly loving to the Linux community. However, despite my best efforts I can't get the thing to work. Initially I tried following directions to set up the driver you can download from the Ralink website. The directions I found were written February first, and Ralink updated the driver February eighth - so as far as I can tell the directions no longer work. After screwing around trying to figure that out for a while I decided to give ndiswrapper a go.
Initially this seemed promising. I just harvested the drivers from the CD and followed one of the many ndiswrapper directions available - most helpful seemed initially to be the Ndiswrapper Troubleshooting Guide found in this forum, however the solutions offered there didn't work either. When I throw an ndiswrapper -l into the terminal it looks promising at first, it tells me the driver is installed and the device is present, but it just doesn't work. When I try iwconfig, or iwlist scan it tells me "no wireless extensions," and "interface doesn't support scanning" respectively. The only devices even listed are lo, eth0, and pan0. There's no wlan0 or anything of the sort.
View 1 Replies
View Related
Jun 11, 2010
having trouble with my asus 1000 rt2860 wireless n card and WPA/PSK/WPA2 connections. Funky thing is it worked in the 2.26.32-21 kernel (iwconfig shows ra0 as the wireless interface), but when the kernel was updated and pushed through in the ubuntu updates to 2.26.32-22 the wireless card won't stay connected and iwconfig says wlan0 is the interface. I checked the proprietary drivers and they said that the driver for my card was active, but not in use. How do I use the ra0 instead of wlan0?
how do i use the driver that's listed as not being used? I'm having to boot up lucid with the older kernel now, it's annoying, lots of programs aren't running as expected as a result. I've tried manually installing the driver from the RaLink website as detailed in many other posts concerning this wireless card. It seems to work for some people, but not with me.
View 1 Replies
View Related
Mar 28, 2011
In our family we have an Eee PC / in Windows7 and openSUSE 11.4 everything is working. In Mint 10 Gnome 64 and 32 bit and Fedora 14 Gnome 32 bit we don t have wireless with persistent USB. iwconfig > no wireless and Networkmanager does not show wireless.
View 8 Replies
View Related
Feb 6, 2010
I still cannot access to internet. May I know why?
Is it due to the Error for wireless request "Set Encode" (8B2A)
The step i did:
1) iwlist eth1 scanning
2) sudo iwconfig eth1 essid shabana key s:xxxxxx
3) invoke firefox ... cannot surf
Do I need to set dhclient? how should I set? DO I need to enable wpa_supplicant?
iwlist eth1 scanning
sound like I was able to connect to ESSID:shabana. Is it true?
The linux is Centos 5.4
View 3 Replies
View Related
Dec 14, 2010
left to its own devices my wireless connects at too low a speed. I have a 20meg internet connection and my wireless is slowing it down to like 3meg. When I reboot into windows it's fine. When I run iwconfig eth1 rate 11M or even 24M the connection is much faster and runs fine, why won't it automatically go higher? Is this the fault of the driver? I am running Broadcom's driver compiled from source. Also, how can I set it to 24M at boot?
Edit: I guess I can put iwconfig eth1 rate 24M in rc.local, but I'd still like to get auto running higher, especially as my signal should be pretty good. Output from iwconfig white rate=auto:
eth1 IEEE 802.11 ESSID:"honeypot"
Mode:Managed Frequency:2.417 GHz Access Point: xxx
Bit Rate=1 Mb/s Tx-Power:24 dBm
Retry min limit:7 RTS thrff Fragment thrff
Encryption keyff
[Code]...
View 1 Replies
View Related
Sep 18, 2010
I am using backtrak 4 because i wont to hack a wireless network and when i wrote iwconfig it dose not work. see this [url] and i am using dell laptop dell inspiron 1545.
View 4 Replies
View Related
Jun 24, 2010
generally whenever there is a wifi connection available fedora will detect and i can establish the connection but today i am not able to see any such wireless network available. I am in a wifi accessible area and i need to know how this can be rectified. i tried iwlist scan in the terminal but that doesnt seem to work
View 1 Replies
View Related
May 28, 2011
My wireless usb will not attempt to connect to my AP even though it shows in ifconfig and iwconfig:further information which i believe may helplspci -v
00:00.0 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
Subsystem: VIA Technologies, Inc. Device aa08
Flags: bus master, 66MHz, medium devsel, latency 8
[code]....
View 1 Replies
View Related
Mar 21, 2010
Ubuntu 9.04 with working wlan. I had to restart router & wap. It doesn't seem to ever retry to connect. I know my router & wap are good, I have wireless working on other laptop (running Puppy) I had to go into 'edit connections' in drop down and use 'wireless' tab then edit 'wireless connection 1' and hit 'apply' is there a better way to do this? also, no connections show up with command 'iwconfig' edit: with ifconfig, eth1 si showing data my ip address and packets sent & rcvd. I think I'll try do duplicate this event and use 'ifconfig eth1 down' and then up again to see if it reconnects.
View 1 Replies
View Related
Apr 9, 2010
I wanna see the wifi signal strength.But when i run the command iwconfig , it tells me 'no wireless extensions'.By googling I found that I need to enable config option CONFIG_NET_RADIO.I see that this has to be done in boot which has config files.So I typed the command grep CONFIG_NET_RADIO /boot/<config-2.6.31.5-127.fc12.i686> (my fedora version is 2.6.31.5-127.fc12.i686).But I got the error as "bash: syntax error near unexpected token `newline' ".I dont know the reason.I also want to know if I have to install driver(ndiswrapper)for viewing wireless signal strength.I thought that the drivers will present default(am not sure).
View 9 Replies
View Related
Jun 8, 2011
I upgraded from kernel-2.6.38.6-27.fc15.x86_64 to kernel-2.6.38.7-30.fc15.x86_64. After the upgrade I no longer have a wireless interface in Network Management. I have a broadcom BCM4312, booting the previous kernel solves this problem.
View 9 Replies
View Related
Apr 18, 2009
Ive been struggling to configure a wireless interface on Fedora 9I need to configure wlan0 command line only with NO display managerIve tried setting up /etc/sysconfig/network-scripts/ifcfg-wlan0 with the right information, doing dhcpbut no ip is retrieved. Checking the dhcp server logs on the DHCP server - no request is received.The link light on the wireless nic is not on either. iwconfig shows it has an Access point associated and an ESSID but im not getting back any IP.There seems to be very little documenta on how to set up wireless nics command line only on Fedora
View 1 Replies
View Related
Mar 21, 2011
I have configured a wireless pcmcia card using ndiswrapper. I'm sure that works, as with the command "iwlist wlan0 scan" gives me back
the list of detected wireless networks. At this point I was wondering: is there a way to detect the new interface (wlan0) with network manager? Even after enabling the wifi card the network manager gnome applet always finds only eth0.
View 2 Replies
View Related
Apr 29, 2010
This is probably the 1 millionth post about WIFI issues. I have tried many sources on the internet but cant get my wireless to work. I have been using another version of linux for long time. But recent edition of that particular linux does not support my wifi any more. Just recently i have tried SuSE and almost fell in love with it. The only problem, WIFI.
I got a Linksys WUSB54GC USB wifi stick which uses RT2800USB native driver. I installed SuSE from the scratch and it found the wifi stick installed the drivers. My only problem is it does not scan for wireless networks. I haev two wifi networks around here. I can connect to them with windows computer with the same wifi stick.
I have tried iwconfig iwlist ifup but i am stuck exactly what to do.
I get the following messages:
It seems to me i am sooo close.
View 1 Replies
View Related
Apr 5, 2009
I'm running fedora 8 and i have a TEW-424ub. I recently ditched windows, and the only disk i could get was a Fedora 8 dvd. I used ndiswrapper to get my driver installed, then I used the iwconfig commands to hook myself up to my wireless. However, every time i do the command
Code:
My comp freezes up. I then decided to use the GUI to set it up, as it might be less aggravating. It found my network, i input the key, double-check, and it atttempts to connect, then asks me once again.'
Also, if I go to Network Configuration, and activate my ndiswrapper device, it gives me the error & my comp freezes up "Set Encode" (8B2A) SET failed on device wlan0:0 ; Invalid argument.
View 5 Replies
View Related
Jul 8, 2011
I have just installed openSuse 11.4 KDE 64-bit on a Dell M1330. When I click on my networking panel, it says WLAN interface is unavailable. I've followed the steps in the stickied post and found the WLAN hardware info, a screenshot of which is below:Uploaded with ImageShack.usNext it says to do this - you need to look at the logs, in particular the info in /var/log/boot.msg. To see this, you need YaST => Miscellaneous => System Logs and select boot.msg.In YaST there is no such option for system logs under miscellaneous, so I can't do that. The results of the sudo /usr/sbin/iwlist scan command produce the following:
root's password:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
[code]....
View 9 Replies
View Related
Aug 22, 2010
I just installed Fedora 13 from the Live CD. FIrst off I read the guide and the first step doesn't even work for me. System>Administration>Network does not exist. If I go to System then Preferences I see a Network Manager but it looks nothing like what these screen shots look like. [url]
No wireless card show up in the wireless tab of Network Manager. How can I fix this since my card is listed in ifconfig and iwconfig. Wifi card is a Zonet zew2500p
View 2 Replies
View Related
Mar 26, 2011
I have a netbook with a onboard WIFI card(Broadcom 5727(rev 01)) and a Realtek RTL8191S USB WIFI donge. Both work.
My problem is; I can't get these to scan for AP's running on channel 12 and 13.
Is there a way to fix this?
Distro: Slackware 13.1
Kernel: 2.6.33.4-smp
View 1 Replies
View Related
Apr 4, 2011
I updated my system from FC13 2.6.34.7-66 to 2.6.34.8-68 for both the kernel and the kmod-wl RPM's. After doing so, iwconfig wlan0 key 1234567890 no longer works. I get an error indicating 'invalid argument'. If I reboot using the previous kernel/wl.ko module, it works The size of the wl.ko module increased in size by almost 30%. Did I somehow get the wrong RPM?
View 2 Replies
View Related
Feb 22, 2011
I just installed Slackware 13.1 on my Asus 1215T, and I've been trying to get it to connect to my wireless network in my home. When I type iwconfig I get no wireless extensions, and ifconfig returns only lo, no wlan0. I read the Slackbook wiki and tried to configure the inet1.conf and wireless.conf but still no luck...
View 12 Replies
View Related
Mar 6, 2011
I've beenhaving some trouble getting my wireless network card working on my Slackware 12 box. Currently it identifies the card and can scan for networks, but I can't seem to join a network. Here's some output:
{8:46:29}gibson:/lib/modules/2.6.33.4-smp## iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: F8:1E:DF:FF:DA:39
ESSID:"MasterControl"
[code]....
It doesn't seem to be accepting the essid setting, and it's giving an error for the key setting. Also, I'm noticing an inconsistency in the wireless protocols. The AP claims that it's 802.11g with rates up to 54 Mb/s. But it should be 802.11n. It's an Apple Airport Extreme and the Radio Mode is set to Automatic and displays "802.11a/n-02.11b/g/n" on the Airport Utility. The interface also claims that it's 802.11g, though shows a rate of 300 Mb/s. It's a Belkin "Play" Wireless USB Adapter (F7D4101).
(Note: I'm using ndiswrapper and the WinXP drivers which were installed from the Belkin software.)
View 1 Replies
View Related
Dec 3, 2010
What i wanted to do was use a linux machine with a wireless and wired interface to act as a router. The wireless interface would be the outside and get its IP via DHCP from the wireless my landlord provides. The wired connection would be for my local pcs. I understand it would be slow having multiple pcs using a single wireless gateway.
View 2 Replies
View Related
Jan 10, 2010
What does the Quality, Signal Level and Noise Level actually mean? Which should I be looking for when looking for good APs?Is Quality the same as RXQ in airodump?
View 1 Replies
View Related
Aug 8, 2010
I have an HP mini laptop (Intel Atom, N270, 1.60GhZ, 1Gb RAM, Win XP ver 2002 SP3) that I upgraded to Ubuntu 10.04 netbook version last nite.I can dual boot, and so far everything under Ubuntu works great - except for the wireless interface. Rebooting back to WinXP, it works fine. The 'sudo lshw -C network' command shows "disabled". Ubuntu sees it, its just disabled. The help file says to make sure its on. It is - there is no physical switch..I am VERY new to this, with no programming experience to speak of.
View 9 Replies
View Related
Sep 2, 2010
I tried to setup a connection as below but face some problem (probably route table setting incorrect). Hope if anyone could shed the light.Basically, I have a PC1 (.1) and PC2 (.130) connected via a PC router. PC router has 2 interfaces: wireless (.2) and ethernet (.129). PC1 connects to PC router via LAN cable/wireless interface, while PC2 connects to PC router via cable. This settings try to simulate 1 wireless connection along the path (and because PC2 is too old to support wireless interface, we need a PC router). These interfaces are all under same 172.16.130.x subnet.
View 3 Replies
View Related
Feb 18, 2011
Just installed Ubuntu 10.10 server and all working great except the wireless interface. The card is an edimax EW-7711ln. I installed ndiswrapper using the driver rt2860.zip found here [URL]. Then I followed this guide to configure /etc/network/interfaces [URL]. I think the driver is loading fine but I can't connect to the access point. Here is some debugging output...
Code:
peter@Peter-Server~$: route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
Code:
peter@Peter-Server~$: iwconfig .....
So I can scan and see the accesspoint with ssid alleycat but I can't connect. I tried disabling all security to see if it was a problem with my key or some encryption settings but even that didn't work. So frustrating because it seems close to working I must be doing something silly. Incase anyone is wondering why I am running a server off a wireless interface, its just a LAMP development server on my home network.
View 1 Replies
View Related
Mar 30, 2011
I am trying to manually configure my wireless interface similar to how I manually configure my wired interfaces on Ubuntu 10.10 (Maverick Meerkat). I have two wired interfaces that use static IP addresses. I set up these interfaces using /etc/network/interface file. I disabled network manager (it was never working correctly to start with). Now, I want to connect my wireless interface (wlan0) to an unsecured wireless private network. I know/can find out all the information about the wireless network (ssid, etc). Also, I need to do this without disconnecting either of my wired interfaces.
I have looked all over the internet/forums for information about how to set up this interface, but nothing I found meets my need. Is there any way I can use iwconfig or the interface file to connect to this wireless connection? Or is there any other tool that will allow me to manually do this?
View 3 Replies
View Related
Jun 18, 2010
The following is my setup. wireless server (ip of this server is 192.168.1.1) -- target board ( wireless client [ip of this is got for wireless server is 192.168.1.3 ] , bridge (192.168.36.1) )-- linux pc ( 192.168.36.3) as show above i have target board for that i have a wireless interface and a linux pc is connected to target board.now the ips are like this for linux pc 192.168.36.3 and my target board bridge ip s 192.168.36.1
my wireless interface got ip from another server like 192.168.1.3 ,now if i do ping on my target board for 192.168.1.1 it goes through wireless interface to the 192.168.1.1 wireless server.but when i do the same from target board connected linux pc its not pinging from linux pc i could able to ping to 192.168.1.3 but not 192.168.1.1 .I think i need to write a iptable rule properly on my target board to forward the 192.168.1.* packtes to wireless interface.
View 14 Replies
View Related
Sep 1, 2011
I have installed SATA driver recently...Even if i can use wifi but i could'nt find any ath0 interface in ifconfig or iwconfig commands....My wifi is taking place through eth1 interface why it happens.....The reason for asking this in order to use aircrack for wep key it says that the injection process only applicable for Athelon interfaces but mine is eth1...I was just trying aircrack-ng...
View 2 Replies
View Related
