Ubuntu Networking :: Wireless Iwconfig Rate Auto Too Low?
Dec 14, 2010
left to its own devices my wireless connects at too low a speed. I have a 20meg internet connection and my wireless is slowing it down to like 3meg. When I reboot into windows it's fine. When I run iwconfig eth1 rate 11M or even 24M the connection is much faster and runs fine, why won't it automatically go higher? Is this the fault of the driver? I am running Broadcom's driver compiled from source. Also, how can I set it to 24M at boot?
Edit: I guess I can put iwconfig eth1 rate 24M in rc.local, but I'd still like to get auto running higher, especially as my signal should be pretty good. Output from iwconfig white rate=auto:
eth1 IEEE 802.11 ESSID:"honeypot"
Mode:Managed Frequency:2.417 GHz Access Point: xxx
Bit Rate=1 Mb/s Tx-Power:24 dBm
Retry min limit:7 RTS thrff Fragment thrff
Encryption keyff
[Code]...
View 1 Replies
ADVERTISEMENT
Feb 28, 2010
Why does this always show: "bit rate=0 kb/s" even when the wirless card is under load? I just ran an online speed test and got 13.07mb/s. How can I check at which speed I am connected to my router?
View 2 Replies
View Related
Mar 28, 2011
In our family we have an Eee PC / in Windows7 and openSUSE 11.4 everything is working. In Mint 10 Gnome 64 and 32 bit and Fedora 14 Gnome 32 bit we don t have wireless with persistent USB. iwconfig > no wireless and Networkmanager does not show wireless.
View 8 Replies
View Related
Feb 6, 2010
I still cannot access to internet. May I know why?
Is it due to the Error for wireless request "Set Encode" (8B2A)
The step i did:
1) iwlist eth1 scanning
2) sudo iwconfig eth1 essid shabana key s:xxxxxx
3) invoke firefox ... cannot surf
Do I need to set dhclient? how should I set? DO I need to enable wpa_supplicant?
iwlist eth1 scanning
sound like I was able to connect to ESSID:shabana. Is it true?
The linux is Centos 5.4
View 3 Replies
View Related
May 28, 2011
My wireless usb will not attempt to connect to my AP even though it shows in ifconfig and iwconfig:further information which i believe may helplspci -v
00:00.0 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
Subsystem: VIA Technologies, Inc. Device aa08
Flags: bus master, 66MHz, medium devsel, latency 8
[code]....
View 1 Replies
View Related
Nov 10, 2010
I have just upgraded my system to Fedora 14. One thing I noticed after running some applications on it is that it is not possible anymore to figure out on what frequency a wireless interface is using. If I set a wireless interface to monitor mode and perform the iwconfig or iwlist command, in the past, I could see the frequency used on the interface, but now, this information is not present anymore. My wireless interfaces are in monitor mode.
Has the frequency information been removed from iwconfig or iwlist commands? If it has, is there another way to report this information?
Here is an output from iwconfig on my system:
View 4 Replies
View Related
Sep 18, 2010
I am using backtrak 4 because i wont to hack a wireless network and when i wrote iwconfig it dose not work. see this [url] and i am using dell laptop dell inspiron 1545.
View 4 Replies
View Related
Mar 21, 2010
Ubuntu 9.04 with working wlan. I had to restart router & wap. It doesn't seem to ever retry to connect. I know my router & wap are good, I have wireless working on other laptop (running Puppy) I had to go into 'edit connections' in drop down and use 'wireless' tab then edit 'wireless connection 1' and hit 'apply' is there a better way to do this? also, no connections show up with command 'iwconfig' edit: with ifconfig, eth1 si showing data my ip address and packets sent & rcvd. I think I'll try do duplicate this event and use 'ifconfig eth1 down' and then up again to see if it reconnects.
View 1 Replies
View Related
Mar 11, 2010
The adapter I purchased (Zonet ZEW2508 ) uses the Ralink 2070 chipset - a fact that originally excited me because Ralink seems to be fairly loving to the Linux community. However, despite my best efforts I can't get the thing to work. Initially I tried following directions to set up the driver you can download from the Ralink website. The directions I found were written February first, and Ralink updated the driver February eighth - so as far as I can tell the directions no longer work. After screwing around trying to figure that out for a while I decided to give ndiswrapper a go.
Initially this seemed promising. I just harvested the drivers from the CD and followed one of the many ndiswrapper directions available - most helpful seemed initially to be the Ndiswrapper Troubleshooting Guide found in this forum, however the solutions offered there didn't work either. When I throw an ndiswrapper -l into the terminal it looks promising at first, it tells me the driver is installed and the device is present, but it just doesn't work. When I try iwconfig, or iwlist scan it tells me "no wireless extensions," and "interface doesn't support scanning" respectively. The only devices even listed are lo, eth0, and pan0. There's no wlan0 or anything of the sort.
View 1 Replies
View Related
Oct 14, 2010
I have a Linksys WUSB600N wireless adapter for my laptop which uses the rt2800usb drivers.My router:
Router Model: Linksys WRT150N v1.1
Firmware Version: DD-WRT v24-sp2 (07/22/09) mini - build 12548M NEWD Eko
The wireless usb adapter connects to my network, and the router is running on mixed mode, except that I cannot seem to get wireless 'n' connection speeds. Both are capable of wireless n. I check the connection info and it is always 54 Mbps. I have set the router wireless on N-only and I lose my connection.Is the standard driver for this usb adapter in Ubuntu 10.4 unable to utilize 'n' speeds?
View 2 Replies
View Related
Dec 8, 2010
When I go to boot up, I ususally have a failedattempt or two at logging in, because my autorepeat rate on the keyboard will often give me morethan one character when I depress a key. SoI put my password in wrong and get a failed attempt.After I log in I usually run:kbdrate -r 6 -d 500This gets my autorepeat rate down to 6 char per secondand delay time to 500 to where I can actually use the keyboard. Is there some place I can run those commands duringboot, so that I don't have the failed and repeated
View 3 Replies
View Related
Jan 11, 2011
I recently switched my desktop from Fedora to CentOS. On Fedora it auto detects my refresh rate at 85 Hz. On CentOS by default it only allowed 60 Hz. I looked at the /etc/X11/xorg.conf file and the display settings were:
[Code]....
View 1 Replies
View Related
Feb 22, 2011
I just installed Slackware 13.1 on my Asus 1215T, and I've been trying to get it to connect to my wireless network in my home. When I type iwconfig I get no wireless extensions, and ifconfig returns only lo, no wlan0. I read the Slackbook wiki and tried to configure the inet1.conf and wireless.conf but still no luck...
View 12 Replies
View Related
Mar 6, 2011
I've beenhaving some trouble getting my wireless network card working on my Slackware 12 box. Currently it identifies the card and can scan for networks, but I can't seem to join a network. Here's some output:
{8:46:29}gibson:/lib/modules/2.6.33.4-smp## iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: F8:1E:DF:FF:DA:39
ESSID:"MasterControl"
[code]....
It doesn't seem to be accepting the essid setting, and it's giving an error for the key setting. Also, I'm noticing an inconsistency in the wireless protocols. The AP claims that it's 802.11g with rates up to 54 Mb/s. But it should be 802.11n. It's an Apple Airport Extreme and the Radio Mode is set to Automatic and displays "802.11a/n-02.11b/g/n" on the Airport Utility. The interface also claims that it's 802.11g, though shows a rate of 300 Mb/s. It's a Belkin "Play" Wireless USB Adapter (F7D4101).
(Note: I'm using ndiswrapper and the WinXP drivers which were installed from the Belkin software.)
View 1 Replies
View Related
Apr 9, 2010
I wanna see the wifi signal strength.But when i run the command iwconfig , it tells me 'no wireless extensions'.By googling I found that I need to enable config option CONFIG_NET_RADIO.I see that this has to be done in boot which has config files.So I typed the command grep CONFIG_NET_RADIO /boot/<config-2.6.31.5-127.fc12.i686> (my fedora version is 2.6.31.5-127.fc12.i686).But I got the error as "bash: syntax error near unexpected token `newline' ".I dont know the reason.I also want to know if I have to install driver(ndiswrapper)for viewing wireless signal strength.I thought that the drivers will present default(am not sure).
View 9 Replies
View Related
Jun 11, 2010
having trouble with my asus 1000 rt2860 wireless n card and WPA/PSK/WPA2 connections. Funky thing is it worked in the 2.26.32-21 kernel (iwconfig shows ra0 as the wireless interface), but when the kernel was updated and pushed through in the ubuntu updates to 2.26.32-22 the wireless card won't stay connected and iwconfig says wlan0 is the interface. I checked the proprietary drivers and they said that the driver for my card was active, but not in use. How do I use the ra0 instead of wlan0?
how do i use the driver that's listed as not being used? I'm having to boot up lucid with the older kernel now, it's annoying, lots of programs aren't running as expected as a result. I've tried manually installing the driver from the RaLink website as detailed in many other posts concerning this wireless card. It seems to work for some people, but not with me.
View 1 Replies
View Related
Sep 1, 2011
I have installed SATA driver recently...Even if i can use wifi but i could'nt find any ath0 interface in ifconfig or iwconfig commands....My wifi is taking place through eth1 interface why it happens.....The reason for asking this in order to use aircrack for wep key it says that the injection process only applicable for Athelon interfaces but mine is eth1...I was just trying aircrack-ng...
View 2 Replies
View Related
Aug 21, 2010
I currently have a command line Ubuntu 9.10 installation.
I wish to be able to have either both wireless and wired connection working
For example: when LAN is connection the wireless is switched off, when LAN is disconnected the wireless comes up (WPA2)
I know that the Network Manager in Gnome does this auto switching for you but I need to know how to do this in command line only.
View 2 Replies
View Related
Jan 28, 2011
I've been trying to get and old PCI wireless card to work on Ubuntu 10.04. The card is a Zonet 1602. It was not recognized automatically.
I have been able to get it to work using ndiswrapper except that when the computer is started it does not automatically connect to the network. I can click on the network icon and select my network from a list and it will connect, including properly authenticating the network key.
I have worked through a lot of information on the web but much of it seems to apply to earlier versions of Ubuntu and some if it does not match what I'm seeing in 10.04.
There is a built in Ethernet controller on the mother board but I have disabled it in the BIOS.
View 3 Replies
View Related
Mar 11, 2011
When iwconfig is redirected thus Code: iwconfig >> wireless.txt things like Code: eth0 - Has no wireles extension are still outputted to the terminal (stdout)
View 2 Replies
View Related
Aug 17, 2011
I am running a version of Ubuntu 10.4 with XFCE loaded (actually Qimo, a distribution for kids). I am using a pci wireless card with a broadcom 43XX chipset and WPA2 authentication using the Broadcom STA driver. In an account with privileges I set the auto eth1 (which is what my wireless card comes up as) to connect automatically, and make available to other users.
When I switch to the kid's account, the wireless connects just fine. Then, if the computer is not used for a period of time, the powersavings mode kicks in. When the computer is woken up, the wireless connection does not attempt to reconnect. If you right click on the networking icon it doesn't even show any available connections, even though it can be found by clicking edit connections. The only way I can get it to reconnect is to restart the machine (I will admit that I did not try to restart the networking service, I will try that tonight).
Any ideas? This has been driving me nuts for a few days now. The users during the day are non technical and can't deal with these kind of issues. I can post more details about the setup (as recommended by the sticky post) tonight. I am at work at the moment and can't get to the machine from here - because it has removed itself from the network again.
View 1 Replies
View Related
Apr 9, 2010
I'm having problems while trying to connect to protected wireless network using iwconfig(8).
When I type in:
Things work ONLY if i DON'T input some numbers after the s: but my actual passkey has numbers.
It outputs this as an error:
my configuration(ThinkPad R61i):
View 8 Replies
View Related
Jun 23, 2010
have to connect to it manually every time i log in where i'll get prompted for the root password to connect.
things worked fine on F12.
View 3 Replies
View Related
Mar 3, 2010
I use iwconfig to connect to my networks cuz i have fluxbox as my window manager. At home my network key is just a phone number and i can connect fine. at my college campus the key is "thinkofspring" and every time i do
Code:
sudo iwconfig wlan0 key thinkofspring
i get an error that the key is invalid or didn't work. Do i need to use a different command for full text keys? I'm running ubuntu 9.10
View 1 Replies
View Related
Jun 27, 2010
I recently got my Belkin USB wireless adapter working by following some other threads in these forums. Now I would like to connect to my access point. iwlist scan works great and I can see my AP along with others. However when I follow the step by step instructions here: [URL]... I fail during the DHCP request with no DHCPOFFERS. My AP is using WEP encryption for now (I've even tried it with open encryption). The thing that I'm seeing or not seeing is that when I set my essid using sudo iwconfig wlan0 essid "GimpsHouse" and then after that do an iwconfig it says off/any. Here is my iwconfig
[code]...
View 3 Replies
View Related
Feb 21, 2010
I have an Atheros AR928X Wireless Adapter (built in to laptop). I can connect to net works with nm-applet fine, but when I use iwconfig, There are no changes. Example:
Code:
$ iwconfig wlan0 essid Convery
$ iwconfig
shows no changes, not even when I set the access point to the right address.
View 3 Replies
View Related
Jul 3, 2011
I have an IBM T60 with Intel 3945ABG WNIC:
Module for this WNIC is loaded:
Code:
Code:
If I execute "iwlist wlan0 scanning", I see the cell I'm interested in:
Code:
I'm able to connect to this cell using Gnome "Wireless Networks" manager, but not with iwconfig. At first I tried to connect to this "bq" network while wlan0 was active("ifconfig wlan0 up") using the iwconfig but this didn't change any of the wlan0 parameters.
Then I tried to shutdown wlan0("ifconfig wlan0 down") and executed:
Code:
Now the changes applied and "iwconfig wlan0" gives following:
Code:
Everything seems to be correct, but I'm still "Not-Associated". I have tried with "iwconfig wlan0 essid bq", "iwconfig wlan0 ap 00:24:14:F9:0B:92", "iwconfig wlan0 essid "bq" mode Managed" etc, but whatever I try, it does not connect. I even did "/etc/init.d/gdm stop" in order to be sure, that Gnome "Wireless Networks" is not interfering with "iwconfig", but this gave no results as well. I can associate with this AP using the Gnome "Wireless Networks" just fine, but for some reason I can't connect using iwconfig.
View 4 Replies
View Related
Feb 26, 2010
i've had problems with a laptops wireless card (using 8.04).i can connect to my network but only at 1mpbs. so, searching through the forums, i found a post that said to issue this command: Code: sudo iwconfig wlan1 rate 11M and that seemed to solve my problem, temporarily.now i'm growing tiresome of doing disabling wireless, issuing the command, and then bringing the wireless card back up. is there a way i can do this automatically upon boot? i checked out my interfaces file, but it only has the loopback setting in there.is there a config file somewhere that i can set the rate of the wireless card manually?
View 2 Replies
View Related
Jun 2, 2010
I have a tenda W311u wireless with a ra3070sta chipset, i read a lot of tutorials to get it working. I recently had my wireless working but just in NetworkManager. I need to get working in console mode, for example when i make a:
Note: The Essid the same i added in the RT2870sta.dat file.
And therefore if i try a dhclient3 ra0 no dhcp offers received.
Rare, but if i start NetworkManager connected to azcor, and i make a dhclient3 ra0 i get an ip very fast.
I try with cnetworkmanager but is complicated and isnt working for me!
View 6 Replies
View Related
Jul 6, 2010
ubuntu is capping my wireless connection at 1Mbps, so everytime I boot up i have to type this:
"iwconfig wlan0 rts 2347 && sudo iwconfig wlan0 frag 2346 && sudo iwconfig wlan0 rate 9MB"
How can I make these settings persistent?
View 2 Replies
View Related
