Ubuntu Networking :: Manual Wireless Interface Configuration?
Mar 30, 2011
I am trying to manually configure my wireless interface similar to how I manually configure my wired interfaces on Ubuntu 10.10 (Maverick Meerkat). I have two wired interfaces that use static IP addresses. I set up these interfaces using /etc/network/interface file. I disabled network manager (it was never working correctly to start with). Now, I want to connect my wireless interface (wlan0) to an unsecured wireless private network. I know/can find out all the information about the wireless network (ssid, etc). Also, I need to do this without disconnecting either of my wired interfaces.
I have looked all over the internet/forums for information about how to set up this interface, but nothing I found meets my need. Is there any way I can use iwconfig or the interface file to connect to this wireless connection? Or is there any other tool that will allow me to manually do this?
View 3 Replies
ADVERTISEMENT
Jul 3, 2009
I have a typical 'linksys' style home wireless router (whose IP is 192.168.0.1) .
If I use DHCP, everything works fine:
Code:
However, if I try to give myself a static IP,
Code:
(I also never understood why the DNS server should not be the real dns server address (some external ip) rather than the router's address? but that is what gets set automatically when using DHCP)
So using manual, it connects, but then the internet doesn't work. The only difference I see when I go to "connection information" when connected with dhcp vs manual is in dhcp mode there is a "default route: 192.168.0.1". Is that the problem? How do I set this "default route" / what is it?
View 3 Replies
View Related
Dec 20, 2009
In the process of making the jump from Ubuntu to Fedora and some of the file placement is catching me. Under Debian, I knew how to setup wireless from boot using /etc/network/interfaces and /etc/wpa_supplicant. Now, I know F12 uses /etc/sysconfig/network-scripts and /etc/wpa_supplicant/wpa_supplicant.conf, but I can't seem to follow the details. Can I use the same commands issued in /etc/network/interfaces in the appropriate /etc/sysconfig/network-scripts file? Can I, basically, copy my /etc/wpa_supplicant.conf to /etc/wpa_supplicant/wpa_supplicant.conf?
View 6 Replies
View Related
Apr 18, 2010
After updating and subsequently restarting today, I can no longer bring up my wireless interface:
ifup wlan0
SIOCSIFFLAGS: Unknown error 132
Could not set interface 'wlan0' UP
SIOCSIFFLAGS: Unknown error 132
SIOCSIFFLAGS: Unknown error 132
Failed to bring up wlan0
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11abg ESSID: off/any
Mode: Managed Access Point: Not-Associated Tx-Power=off
Retry long limit:7 RTS thr: off Fragment thr:off
Encryption key:off
Power Management:off
lsmod | grep iwl
iwl3945 77904 0
iwlcore 127432 1 iwl3945
mac80211 180929 2 iwl3945, iwlcore
cfg80211 142905 3 iwl3945, iwlcore, mac80211
View 1 Replies
View Related
Apr 30, 2010
I tried installing the driver following the instructions in the link given below.
viewtopic.php?t=7949
But now also its now working either. After installing the outputs are given below.
[Code].....
View 7 Replies
View Related
May 25, 2011
i am wanting to turn my Debian box into a wireless AP, but for some unknown reason the wireless card won't switch into master mode when i run the command #iwconfig wlan1 mode master i get this Error for wireless request "Set Mode" (8B06): SET failed on device wlan1 ; Invalid argument. what does this mean and what do i need to configure/install to get it to work my wirless card is supported i checked it's a zydas chipset using the zd1211rw driver SMC EZ Connect SMCWUSB-G [URL]
View 14 Replies
View Related
Dec 9, 2010
I have been trying to get my wireless interface work but i am unable to find a driver for the wireless interface.
View 1 Replies
View Related
Dec 10, 2009
I have b43 wireless. In network Configuration on system->administration the interface it appears as inactive it appers in hardware also as b43 associated to wlan0 but i cannot have access to any wireless network. What i have to do to put this b43 to work.
View 11 Replies
View Related
Jul 8, 2011
I have just installed openSuse 11.4 KDE 64-bit on a Dell M1330. When I click on my networking panel, it says WLAN interface is unavailable. I've followed the steps in the stickied post and found the WLAN hardware info, a screenshot of which is below:Uploaded with ImageShack.usNext it says to do this - you need to look at the logs, in particular the info in /var/log/boot.msg. To see this, you need YaST => Miscellaneous => System Logs and select boot.msg.In YaST there is no such option for system logs under miscellaneous, so I can't do that. The results of the sudo /usr/sbin/iwlist scan command produce the following:
root's password:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
[code]....
View 9 Replies
View Related
Jun 17, 2011
I have a webserver with 3 virtual interfaces named eth0:1 eth0:3 and eth0:3. Until yesterday all the virtual ip's worked but eth0:1 decided that it just won't work anymore since yesterday. The configs are:
eth0
Code:
DEVICE=eth0
USERCTL=no
ONBOOT=yes
BOOTPROTO=none
BROADCAST=xx.xxx.26.190
NETWORK=xx.xxx.26.160
NETMASK=255.255.255.224
IPADDR=xx.xxx.26.174
GATEWAY=xx.xxx.26.161
eth0:1
Code:
MTU=""
NETMASK=255.255.255.224
ONPARENT=yes
BROADCAST=xx.xxx.26.191
BOOTPROTO=none
NAME=""
IPADDR=xx.xxx.26.175
NETWORK=xx.xxx.26.160
ONBOOT=yes
DEVICE=eth0:1
eth0:3
Code:
MTU=""
NETMASK=255.255.255.224
ONPARENT=yes
BROADCAST=xx.xxx.26.191
BOOTPROTO=none
NAME=""
IPADDR=xx.xxx.26.182
NETWORK=xx.xxx.26.160
ONBOOT=yes
DEVICE=eth0:3
eth0:4
Code:
MTU=""
NETMASK=255.255.255.224
ONPARENT=yes
BROADCAST=xx.xxx.26.191
BOOTPROTO=none
NAME=""
IPADDR=xx.xxx.26.187
NETWORK=xx.xxx.26.160
ONBOOT=yes
DEVICE=eth0:4
route-eth0
Code:
ADDRESS0=0.0.0.0
NETMASK0=0.0.0.0
GATEWAY0=xx.xxx.26.161
eth0:3 and eth0:4 still work, but 2 doesn't
View 4 Replies
View Related
Dec 3, 2010
What i wanted to do was use a linux machine with a wireless and wired interface to act as a router. The wireless interface would be the outside and get its IP via DHCP from the wireless my landlord provides. The wired connection would be for my local pcs. I understand it would be slow having multiple pcs using a single wireless gateway.
View 2 Replies
View Related
Aug 8, 2010
I have an HP mini laptop (Intel Atom, N270, 1.60GhZ, 1Gb RAM, Win XP ver 2002 SP3) that I upgraded to Ubuntu 10.04 netbook version last nite.I can dual boot, and so far everything under Ubuntu works great - except for the wireless interface. Rebooting back to WinXP, it works fine. The 'sudo lshw -C network' command shows "disabled". Ubuntu sees it, its just disabled. The help file says to make sure its on. It is - there is no physical switch..I am VERY new to this, with no programming experience to speak of.
View 9 Replies
View Related
Sep 2, 2010
I tried to setup a connection as below but face some problem (probably route table setting incorrect). Hope if anyone could shed the light.Basically, I have a PC1 (.1) and PC2 (.130) connected via a PC router. PC router has 2 interfaces: wireless (.2) and ethernet (.129). PC1 connects to PC router via LAN cable/wireless interface, while PC2 connects to PC router via cable. This settings try to simulate 1 wireless connection along the path (and because PC2 is too old to support wireless interface, we need a PC router). These interfaces are all under same 172.16.130.x subnet.
View 3 Replies
View Related
Feb 18, 2011
Just installed Ubuntu 10.10 server and all working great except the wireless interface. The card is an edimax EW-7711ln. I installed ndiswrapper using the driver rt2860.zip found here [URL]. Then I followed this guide to configure /etc/network/interfaces [URL]. I think the driver is loading fine but I can't connect to the access point. Here is some debugging output...
Code:
peter@Peter-Server~$: route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
Code:
peter@Peter-Server~$: iwconfig .....
So I can scan and see the accesspoint with ssid alleycat but I can't connect. I tried disabling all security to see if it was a problem with my key or some encryption settings but even that didn't work. So frustrating because it seems close to working I must be doing something silly. Incase anyone is wondering why I am running a server off a wireless interface, its just a LAMP development server on my home network.
View 1 Replies
View Related
Feb 26, 2010
running 9.10 server, have SSH access through LAN, but I'd like to move box out of my neighbor's (shared internet & the router's in his place) and into my own space. Would have done so already, but I can't get the wireless working. Details below:lshw -C network gives:
Code:
*-network:0 DISABLED
description: Wireless interface
[code]....
View 2 Replies
View Related
Aug 14, 2010
I've been having issues setting up the wireless interface on my Ubuntu server (command-line only, no GUI) and I can't seem to get it working. It seems as though the card is recognized, the drivers are installed and the interface is up, but it fails to connect. I have no idea where I'm going wrong. I have WPA and a MAC filtering setup on my wireless router. An exception has been made for this PC's MAC address and I've manually entered the connection details into /etc/network/interfaces.
[Code]...
View 2 Replies
View Related
Jun 8, 2011
I upgraded from kernel-2.6.38.6-27.fc15.x86_64 to kernel-2.6.38.7-30.fc15.x86_64. After the upgrade I no longer have a wireless interface in Network Management. I have a broadcom BCM4312, booting the previous kernel solves this problem.
View 9 Replies
View Related
Jun 18, 2010
The following is my setup. wireless server (ip of this server is 192.168.1.1) -- target board ( wireless client [ip of this is got for wireless server is 192.168.1.3 ] , bridge (192.168.36.1) )-- linux pc ( 192.168.36.3) as show above i have target board for that i have a wireless interface and a linux pc is connected to target board.now the ips are like this for linux pc 192.168.36.3 and my target board bridge ip s 192.168.36.1
my wireless interface got ip from another server like 192.168.1.3 ,now if i do ping on my target board for 192.168.1.1 it goes through wireless interface to the 192.168.1.1 wireless server.but when i do the same from target board connected linux pc its not pinging from linux pc i could able to ping to 192.168.1.3 but not 192.168.1.1 .I think i need to write a iptable rule properly on my target board to forward the 192.168.1.* packtes to wireless interface.
View 14 Replies
View Related
Dec 12, 2010
Ubuntu @ Powerbook G4 400mhz
What's about:
I'm trying to install Ubuntu (or lubuntu) to this old Powerbook [URL] with 400mhz PPC CPU. I got it instslled and can use the terminal, but can't get the xserver running! The problem is the display is verey sensitiv with correct resulution and frequency, if it is not OK, it will not show enything (well, some colors like northern lights but nothing else ) I can login using the keyboard and hear the logon sound of gnome. but of cause i cant see anything I got no external monitor for testing.
Now the big question: how can i setup the grafic card in the actuel version of ubuntu? here i found some info, but it's not working anymore with 10.10 [URL]
here i found the following datas for the screen:
resolution: 1152x768horizontal
31-46 vertikal
50-70
View 1 Replies
View Related
Jun 30, 2015
I have just installed Debian Weezy and for some reason it just does not see my router.1) is there a good network config script I can use?if not then what files must be edited to setup the network?When I attempt to ping the router, it does not see it. I have checked the cables etc.
View 6 Replies
View Related
Apr 25, 2016
I am trying to set up a static IP for the pi.
Code: Select allcat /etc/network/interfaces
this should bring up something like iface eth0 inet dhcp
View 3 Replies
View Related
Oct 12, 2010
I installed RHEL 6 Beta 2 on ESX box and found that network is to be manually started through ifup command.
View 6 Replies
View Related
Apr 17, 2010
I really not successed to install Bind, I installed Rhl9, After installation, i want to confirm the name server using dig command also, prob to use dig command with different option
View 1 Replies
View Related
Apr 18, 2009
Ive been struggling to configure a wireless interface on Fedora 9I need to configure wlan0 command line only with NO display managerIve tried setting up /etc/sysconfig/network-scripts/ifcfg-wlan0 with the right information, doing dhcpbut no ip is retrieved. Checking the dhcp server logs on the DHCP server - no request is received.The link light on the wireless nic is not on either. iwconfig shows it has an Access point associated and an ESSID but im not getting back any IP.There seems to be very little documenta on how to set up wireless nics command line only on Fedora
View 1 Replies
View Related
Nov 10, 2010
I have just upgraded my system to Fedora 14. One thing I noticed after running some applications on it is that it is not possible anymore to figure out on what frequency a wireless interface is using. If I set a wireless interface to monitor mode and perform the iwconfig or iwlist command, in the past, I could see the frequency used on the interface, but now, this information is not present anymore. My wireless interfaces are in monitor mode.
Has the frequency information been removed from iwconfig or iwlist commands? If it has, is there another way to report this information?
Here is an output from iwconfig on my system:
View 4 Replies
View Related
Sep 21, 2010
I am in the midst of upgrading my F11 computer to F13. I have run PreUpgrade, and the files have downloaded, it's restarted and now it's asking me to do the Manual TCP/IP Configuration. I have only enabled IPV4. It's asking for the following info (which I can't seem to get right)
[Code]....
The IP I want the computer to have is 192.168.0.5, my router is 192.168.0.1, my subnet is 255.255.255.0 I don't know what the Name server is for. Do I need to put the above into into any of the fields above? I've tried a few times but with no luck.
View 3 Replies
View Related
Jan 7, 2010
From where I can download Openswan for my RHEL 5. Please if possible, give me installation and configuration manual.
View 3 Replies
View Related
Mar 11, 2010
The adapter I purchased (Zonet ZEW2508 ) uses the Ralink 2070 chipset - a fact that originally excited me because Ralink seems to be fairly loving to the Linux community. However, despite my best efforts I can't get the thing to work. Initially I tried following directions to set up the driver you can download from the Ralink website. The directions I found were written February first, and Ralink updated the driver February eighth - so as far as I can tell the directions no longer work. After screwing around trying to figure that out for a while I decided to give ndiswrapper a go.
Initially this seemed promising. I just harvested the drivers from the CD and followed one of the many ndiswrapper directions available - most helpful seemed initially to be the Ndiswrapper Troubleshooting Guide found in this forum, however the solutions offered there didn't work either. When I throw an ndiswrapper -l into the terminal it looks promising at first, it tells me the driver is installed and the device is present, but it just doesn't work. When I try iwconfig, or iwlist scan it tells me "no wireless extensions," and "interface doesn't support scanning" respectively. The only devices even listed are lo, eth0, and pan0. There's no wlan0 or anything of the sort.
View 1 Replies
View Related
Feb 9, 2011
I'm a student who is working on a wireless research project. I have a madwifi driver for Atheros chipset on Debian Linux. With having the wireless interface get into monitor mode, I want to forward the captured packets from the wireless interface to the other Ethernet interface so that a different computer which is connected to this machine via Ethernet receives those packets. I checked that alll packets are received in the wireless interface using TCPDUMP. I tried to forward those packets with IPTABLES like 'iptables -p FORWARD -i ath0 -o eth2 -j ACCEPT' However, I couldn't see any packets forwarded to eth2 using TCPDUMP.
View 5 Replies
View Related
Dec 3, 2015
Creating a separate /tmp partition manually during install prevents a clean shutdown.
Setup: Debian 8 minimal server configuration (SSH only) using net install as virtual machine on Windows Server 2012 R2 Hyper-V (Gen 2).
1024 MB RAM, 20 GB VHDX, and 1 Processor, EFI boot
Packages installed: openssh-server, sudo, unattended-upgrades, bsd-mailx postfix
Application: IPv6 gateway using 6in4 tunnel
Symptoms: When shutting down the operating system (poweroff or reboot), the message
A start job is running for Unattended-Upgrades ( xx seconds / no limit ).is displayed on the console and will persist for several minutes before eventually timing out and shutting down.I've tried several different configurations. Any configuration that creates /tmp automatically (whole disk with single partition, or disk with separate /home, /var, and /tmp partitions) works fine and shuts down promptly. When I partition the disk manually (512 MB EFI Boot, 17 GB /, 3 GB /var, 512 MB /tmp, and 512+ swap) the problem occurs. I've narrowed it down to just the /tmp partition by testing and comparing various configurations (including/excluding partitions, placing partitions on a separate disk, changing the partition sizes, matching against automatic configurations, etc.).
I have also compared the /etc/fstab and /etc/default/tmpfs configuration file between working and non-working systems and cannot see any meaningful difference.
View 0 Replies
View Related
