I upgraded from kernel-2.6.38.6-27.fc15.x86_64 to kernel-2.6.38.7-30.fc15.x86_64. After the upgrade I no longer have a wireless interface in Network Management. I have a broadcom BCM4312, booting the previous kernel solves this problem.
View 9 Replies
I am writing this using the 2.6.31-17 generic kernel after rebooting and selecting NOT to use the 2.6.31-18 kernel which was just installed. The newer kernel would not recognize/activate my Atheros AR2418 wireless adapter and, when I connected to the ethernet and did updates, there were no hardware drivers available. I haven't needed proprietary drivers since I upgraded to 9.04 and 9.10 works fine with older kernel.
View 1 Replies View RelatedIve been struggling to configure a wireless interface on Fedora 9I need to configure wlan0 command line only with NO display managerIve tried setting up /etc/sysconfig/network-scripts/ifcfg-wlan0 with the right information, doing dhcpbut no ip is retrieved. Checking the dhcp server logs on the DHCP server - no request is received.The link light on the wireless nic is not on either. iwconfig shows it has an Access point associated and an ESSID but im not getting back any IP.There seems to be very little documenta on how to set up wireless nics command line only on Fedora
View 1 Replies View RelatedI have just upgraded my system to Fedora 14. One thing I noticed after running some applications on it is that it is not possible anymore to figure out on what frequency a wireless interface is using. If I set a wireless interface to monitor mode and perform the iwconfig or iwlist command, in the past, I could see the frequency used on the interface, but now, this information is not present anymore. My wireless interfaces are in monitor mode.
Has the frequency information been removed from iwconfig or iwlist commands? If it has, is there another way to report this information?
Here is an output from iwconfig on my system:
I have just installed openSuse 11.4 KDE 64-bit on a Dell M1330. When I click on my networking panel, it says WLAN interface is unavailable. I've followed the steps in the stickied post and found the WLAN hardware info, a screenshot of which is below:Uploaded with ImageShack.usNext it says to do this - you need to look at the logs, in particular the info in /var/log/boot.msg. To see this, you need YaST => Miscellaneous => System Logs and select boot.msg.In YaST there is no such option for system logs under miscellaneous, so I can't do that. The results of the sudo /usr/sbin/iwlist scan command produce the following:
root's password:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
[code]....
after upgrading to kernel 2.6.34.6 I have two issues which I don't know how to solve. First and more important is an issue with boot process. The boot is ok until it is supposed to switch to gnome desktop. Then suddenly the graphics become a weird line pattern with no discernible features. Only a rectangle which moves upon moving the mouse. This can be resolved by switching to a console, logging in there and killing the gnome-session. (with kill -9) Then, instantly the desktop appears as usual, the background is loaded, the panels come up and all seems well.
I have no clue what causes this. I thought there's a display driver problem but since I can actually get back to the normal graphics state I'm confused. Also glxinfo says:
Code:
[Me@Plato ~]$ glxinfo | grep render
direct rendering: Yes
OpenGL renderer string: Mesa DRI R600 (RV620 95C4) 20090101 TCL DRI2
Secondly the nm-applet doesn't work until restartet. Normally I expect to see an authorization request window, prompting for my passwd to start wireless networking, and the little icon in the panel. Both don't show up until I kill the nm-applet process and restart it. After I do this everything is back to normal and working as expected.
I assume if problem one is solved, two won't be a problem anymore because I expect the password dialog hidden somewhere in the background when the graphics is all garbled..
Edit: Failed to mention thath my graphics card is ATI3470 as shown in the signature...
I am trying to install the Nvidia Quadro NVS 110 169.04 drivers but am having issues during install. Prior to attempting my install I did install the kernel-devel rpm so it can compile. after running the RPM I get. Quote: No precompiled kernel interface was found to match your kernel; would you like the installer to attempt to download a kernel interface for your kernel from the NVIDIA ftp site [URL]?
which of course does not work. next it says Quote: "No precompiled kernel interface was found to match your kernel; this means that the installer will need to compile a new kernel interface.. i hit okay and move on to. Quote: Error: Unable to find the kernel sources tree for the currently running kernel. Please make sure you have installed the kernel source files for your kernel and that they are properly configured; on Red Hat linux systems, for example be sure you have the 'kernel-source' or 'kernel-devel' RPM installed. if you know the correct kernel source files are installed, you may specify the kernel source path with the "--kernel-source-path' command line option
I have upgraded Intel Core2 Duo (Macbook Pro laptop) system to Fedora 15. I believe I have the proper firmware driver installed for my wireless network adapter. In Gnome I can click on the network status icon and select my wireless network, however nothing happens after that. Fedora does not prompt for my wireless network password, and no network connectivity is established. What can I do that would get my system to connect to the wireless network?
View 14 Replies View RelatedI've been using fedora on my Lenovo R61i since I got it...I believe the first version I used on this laptop was f10. I always try to keep it on the latest distro and I also enjoy a clean install every year or so. One thing I was always impressed with was how quickly I could go from sleep to back up and online. So I decided it was time for a clean install this weekend to fedora 15. Now when I wake it up (open the lid), it takes over a minute for the wifi to connect again. This hasn't been the case for the last 4 distro's so I'm wondering what I can do to speed that process back up, is there a particular package I can downgrade or is this something on their radar already and I should just wait for an upgrade?
View 3 Replies View RelatedI'm having the same Harker2010 's problem.Running 10.04 LTS on a Dell latitude D-820, and switching between lan and wifi worked OK until last upgrade.Harker2010's screenshots are also valid for my problem. I've tried everything I see on this post but the problem still there.
View 1 Replies View RelatedWhat i wanted to do was use a linux machine with a wireless and wired interface to act as a router. The wireless interface would be the outside and get its IP via DHCP from the wireless my landlord provides. The wired connection would be for my local pcs. I understand it would be slow having multiple pcs using a single wireless gateway.
View 2 Replies View RelatedI have a Broadcom wireless card in my hp dv6500z laptop, I had it all working properly in FC9 thanks to bbfuller and his post on the subject. After I upgraded to FC11 I have been unable to get it to connect.
I can see my neighbor's sites and suppose I could see my own if the SSID was allowed to broadcast but I keep that turned off. I put in all of the setting, including the network security key, but it won't connect, then when I go back and look again, the security key is not even close to what I put in; it gets changed to a huge string of characters.
I redownloaded broadcom-wl-4.150.10.5.tar.bz2.tar and followed the instruction on the post once again but no luck, which, after I thought about it, was a waste of time because if I can see other's wireless, then the card must be working. I have tried using Network Manager and not using Network Manager and still no luck...
I wireless network card is Broadcom Corporation BCM431, but is doesn't work after I update kernel from
2.6.29.6-217.2.7 to 2.6.29.6-217.2.8.
Linux localhost.localdomain 2.6.29.6-217.2.7.fc11.x86_64 #1 SMP Fri Aug 14 20:53:08 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux
I have an HP mini laptop (Intel Atom, N270, 1.60GhZ, 1Gb RAM, Win XP ver 2002 SP3) that I upgraded to Ubuntu 10.04 netbook version last nite.I can dual boot, and so far everything under Ubuntu works great - except for the wireless interface. Rebooting back to WinXP, it works fine. The 'sudo lshw -C network' command shows "disabled". Ubuntu sees it, its just disabled. The help file says to make sure its on. It is - there is no physical switch..I am VERY new to this, with no programming experience to speak of.
View 9 Replies View RelatedI tried to setup a connection as below but face some problem (probably route table setting incorrect). Hope if anyone could shed the light.Basically, I have a PC1 (.1) and PC2 (.130) connected via a PC router. PC router has 2 interfaces: wireless (.2) and ethernet (.129). PC1 connects to PC router via LAN cable/wireless interface, while PC2 connects to PC router via cable. This settings try to simulate 1 wireless connection along the path (and because PC2 is too old to support wireless interface, we need a PC router). These interfaces are all under same 172.16.130.x subnet.
View 3 Replies View RelatedJust installed Ubuntu 10.10 server and all working great except the wireless interface. The card is an edimax EW-7711ln. I installed ndiswrapper using the driver rt2860.zip found here [URL]. Then I followed this guide to configure /etc/network/interfaces [URL]. I think the driver is loading fine but I can't connect to the access point. Here is some debugging output...
Code:
peter@Peter-Server~$: route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
Code:
peter@Peter-Server~$: iwconfig .....
So I can scan and see the accesspoint with ssid alleycat but I can't connect. I tried disabling all security to see if it was a problem with my key or some encryption settings but even that didn't work. So frustrating because it seems close to working I must be doing something silly. Incase anyone is wondering why I am running a server off a wireless interface, its just a LAMP development server on my home network.
I am trying to manually configure my wireless interface similar to how I manually configure my wired interfaces on Ubuntu 10.10 (Maverick Meerkat). I have two wired interfaces that use static IP addresses. I set up these interfaces using /etc/network/interface file. I disabled network manager (it was never working correctly to start with). Now, I want to connect my wireless interface (wlan0) to an unsecured wireless private network. I know/can find out all the information about the wireless network (ssid, etc). Also, I need to do this without disconnecting either of my wired interfaces.
I have looked all over the internet/forums for information about how to set up this interface, but nothing I found meets my need. Is there any way I can use iwconfig or the interface file to connect to this wireless connection? Or is there any other tool that will allow me to manually do this?
The following is my setup. wireless server (ip of this server is 192.168.1.1) -- target board ( wireless client [ip of this is got for wireless server is 192.168.1.3 ] , bridge (192.168.36.1) )-- linux pc ( 192.168.36.3) as show above i have target board for that i have a wireless interface and a linux pc is connected to target board.now the ips are like this for linux pc 192.168.36.3 and my target board bridge ip s 192.168.36.1
my wireless interface got ip from another server like 192.168.1.3 ,now if i do ping on my target board for 192.168.1.1 it goes through wireless interface to the 192.168.1.1 wireless server.but when i do the same from target board connected linux pc its not pinging from linux pc i could able to ping to 192.168.1.3 but not 192.168.1.1 .I think i need to write a iptable rule properly on my target board to forward the 192.168.1.* packtes to wireless interface.
This is my first post here. I'm using Opensuse 11.2 (Gnome)and the inbuilt kernel is 2.6.31.xx. My laptop is having bcm4312 (14e4 : 4315 id)chipset for wireless. (0e:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) 0e:00.0 0280: 14e4:4315 (rev 01) ) I have read multiple times here in some threads that this kernel will require Broadcom-wl drivers(Tried ,No success with this) And If I want to use b43 drivers , then I need to go for the 2.6.32 kernel (stable one from this release). I've done the same exactly given in some other link -
Steps-
make mrproper
make menuconfig
make dep
make clean
make bzImage
make modules
make modules_install
After rebooting it's not showing anything new.Just the boot menu with the older one. Experts, Kindly let me know what I'm missing?
I have changed kernel to 2.6.33. After that ifconfig command shows only my ethernet card, wireless card have disappeared. What is wrong. In the old kernel everything works fine. I am sure that i have installed wi-fi stuff with kernel.
View 14 Replies View Relatedrunning 9.10 server, have SSH access through LAN, but I'd like to move box out of my neighbor's (shared internet & the router's in his place) and into my own space. Would have done so already, but I can't get the wireless working. Details below:lshw -C network gives:
Code:
*-network:0 DISABLED
description: Wireless interface
[code]....
Testing distribution. Installed Linux 3.0 but left 2.6.32 on as backup. When I boot into the old kernel, wireless mostly works OK, but never when I boot with the new kernel.
Results of dmesg|grep wlan0 on 2.6:
[ 22.005102] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.196774] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.644779] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 30.688053] wlan0: direct probe to AP 00:19:5b:06:9f:ba (try 1)
[ 30.694053] wlan0: direct probe responded
[Code]...
Noticing the Access Point looked like it needed the MAC address, I ran iwconfig wlan0 ap <MACADDRESS> and sometimes it will work, and wicd can connect to the access point. But sometimes the command fails to run.
I've been having issues setting up the wireless interface on my Ubuntu server (command-line only, no GUI) and I can't seem to get it working. It seems as though the card is recognized, the drivers are installed and the interface is up, but it fails to connect. I have no idea where I'm going wrong. I have WPA and a MAC filtering setup on my wireless router. An exception has been made for this PC's MAC address and I've manually entered the connection details into /etc/network/interfaces.
[Code]...
I'm a student who is working on a wireless research project. I have a madwifi driver for Atheros chipset on Debian Linux. With having the wireless interface get into monitor mode, I want to forward the captured packets from the wireless interface to the other Ethernet interface so that a different computer which is connected to this machine via Ethernet receives those packets. I checked that alll packets are received in the wireless interface using TCPDUMP. I tried to forward those packets with IPTABLES like 'iptables -p FORWARD -i ath0 -o eth2 -j ACCEPT' However, I couldn't see any packets forwarded to eth2 using TCPDUMP.
View 5 Replies View RelatedNo wireless after upgrading to linux kernel 3.0 in opensuse 11.4. I'm using Kde and gnome 3, everything was working fine under the 2.6.39 kernel, but now both only detects my wired connection. Any help resolving this would be greatly appreciated. I have a Netgear WNDA3100 adapter that uses the Atheros drivers. It also is no longer detected in my Fedora 15 after upgrading the kernel, but it still works in Mint 11 with the 2.6.38.8 kernel.
View 9 Replies View RelatedRecently, I installed a fresh 64bit Lucid Lynx on my Lenovo B450 laptop (previously on Mint8 64bit, based on Karmic). It's been really nice and speedy except for one thing - USB transfers to thumb drives and external hard drives were really slow (just like in the older Ubuntu releases). I had found some forum discussions on a fix to this by way of a kernel upgrade so I decided to go for it.
Went ahead and downloaded the kernel DEBs from [URL] and installed them. Voila! USB speed issue was fixed! Everything else seemed to work fine, except for some minor troubles with burning CDs and DVDs (I think I need to upgrade the drive's firmware - pretty bad situation as the update only runs on Windows).
However, the one 'bug' or 'annoyance' I noticed straight away was that my wireless wouldn't autostart after booting into the OS with the new 2.6.34-020634-generic (x86_64) kernel. I'd have to right-click on the NetworkManager icon on the notification tray and left-click '[ ] Enable Wireless' to flag the checkbox and my wireless would come right up and work ok (WPA2 at home, WEP at the office). Not a major problem, but this has been pretty irritating to say the least.
If i use yum update option it upgrades to latest kernel but i only want to upgrade to kernel-2.6.31.6.
View 8 Replies View RelatedI have a Dell Vostro 3500, which has a Broadcom wifi card. It requires non free drivers. So far it has been working well. However, after updating the kernel (via yum update), my wifi card (it used to be eth1) is totally gone: $ ifconfig eth1 eth1: error fetching interface information: Device not found The wireless indicator does not light up either. The kernel version is
[code]...
The adapter I purchased (Zonet ZEW2508 ) uses the Ralink 2070 chipset - a fact that originally excited me because Ralink seems to be fairly loving to the Linux community. However, despite my best efforts I can't get the thing to work. Initially I tried following directions to set up the driver you can download from the Ralink website. The directions I found were written February first, and Ralink updated the driver February eighth - so as far as I can tell the directions no longer work. After screwing around trying to figure that out for a while I decided to give ndiswrapper a go.
Initially this seemed promising. I just harvested the drivers from the CD and followed one of the many ndiswrapper directions available - most helpful seemed initially to be the Ndiswrapper Troubleshooting Guide found in this forum, however the solutions offered there didn't work either. When I throw an ndiswrapper -l into the terminal it looks promising at first, it tells me the driver is installed and the device is present, but it just doesn't work. When I try iwconfig, or iwlist scan it tells me "no wireless extensions," and "interface doesn't support scanning" respectively. The only devices even listed are lo, eth0, and pan0. There's no wlan0 or anything of the sort.
I seem to be missing some step(s) for getting an interface to appear in the output of ifconfig and
iwconfig for a RT2870 wireless USB 802.11n adapter (made by Panda Wifi). Let me step you
through what's I've done thus far.
After plugging the device in, it's low-level identification is as follows (see bold):
root@xps720# lsusb
Bus 002 Device 002: ID 046d:0b06 Logitech, Inc.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870 Wireless Adapter
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[Code]....
