Fedora Networking :: Unable To Connect To WPA2 Network
May 9, 2009
O currently have 2 USB WiFi adaptors: a Linksys WUSB54G v4 and a D-Link DWA-110. Both these USB adaptors worked extremely well in Windows: they could connect to any network: unsecured, WEP and WPA1/2I have tested these adaptors in DreamLinux, OpenSUSE and Mandriva: in these 3 distributions, i could use both adaptors to connect to my home's WPA2 network.Both adaptors also work well in Fedora 10.In Fedora 11 Alpha though, its a different thing: only the D-Link is able to connect to the home WPA2 network. My Linksys WUSB54Gv4 can 'see' the network, but when i enter in the WPA2 key, it takes forever to try to negotiate a connection before timing out and disconnecting.
I have a problem with my RT2860 in my Eee PC 901 running F13. It connected fine in F12 when I installed the akmod-rt2860 driver. I enter my WPA key, then it tries to connect, but the WPA key screen appears again saying that I may have typed in my WPA key incorrectly. However, I checked and it is the right WPA key.
My college runs a WPA2 LEAP secured wireless network, and I am having problems connecting to it under Ubuntu. I can connect to it just fine under Windows, just not under Ubuntu. Under Ubuntu I can connect to other networks such as my home WEP secured wireless network, so it shouldn't be a hardware or driver issue.
When I do connect to the WPA2 LEAP network it recognizes the network and tries to connect, it pops up the login box for me to enter my username and password, but after I click connect it pops back up again about 10 seconds later. It pops up like this about 3 times total, then after the third time it stops trying to connect and the Wireless Network Disconnected message is shown.
Im trying to connect to my wireless network via terminal. My wifi network has a WPA2 encription. Im running ubuntu server 10.04. wifi interfaces are active, i can "see" my network with airodump. The only thing is i dont really know how to configure my iwconfig to connect to it.
I just installed Ubuntu 10.04, everything is fine, but the wireless. When I try to connect to my WPA2 protected network, it is grayed out. SO I click Connect to Hidden Wireless Network, and this window pops up. I put in my network name, the security type, and password. It acts like it is connecting, the wireless icon is going up and down. But then another window pops up, saying Authentication required by wireless network and the down arrow is grayed out. Screenshot.jpg
I just switched from Ubuntu to Fedora 13 because I was unable to get Ubuntu to connect to wireless networks. I tried everything suggested in help and forums, and kept getting "Bad Password" with WICD and Network Manager. Now, with Fedora...I still can't connect.
Problem #1: The guide says to "...make sure that the relevant wireless interface (usually eth0 or eth1) is controlled by NetworkManager," and that I do this via: System>Administration>Network
However, there is no Network option under System>Administration.
Problem #2: I open Network Manager, which displays a list of networks. I click on mine, configure it with WPA and the right password, and it fails to connect: "The network connection has been disconnected."
how can i connect to the wireless network(WPA/WPA2)? i dont have network manager,so help me with terminal. i download wpasusclinet,but help me from first.
I have a laptop (running Arch Linux) and a desktop. Until recently my desktop computer ran Arch but I'm taking Debian for a spin now. At my home there is a wireless network with WPA2 encoding. I use the wicd gui to connect to this. I assume, that since I can see the SSID in the wicd window, all drivers are correctly installed and functioning. On my Arch computer, wicd reports this SSID as having WPA2 encoding, but on the Debian computer, it shows up as WEP. Even when I choose the correct encryption thing, WPA2 (preshared key), and put the correct password in, I can't get a connection up.
I recently installed KDE and just found that it cannot connect to my school wireless which uses WPA2. It keep asking Secretes for , even after I input everything correctly. It works fine with not secured wireless.In Gnome there was no problem with connecting to this wireless service.
I've FC10 installed. After updating a few days back, I'm unable to use Network Manager to connect to the net through my USB Modem. All the threads I've read say to do
Code: yum update NetworkManager but how can I do it without net connection? Can anyone post the exact link of the Network Manager's latest and BUG-FREE rpm so that I can directly run it?
I have had my network setup and working with WEP for a long time. Also Windows 7 is working fine from the same laptop. I can't figure out why the essid is scrambled. Here is the output of iwconfig:
Unsecured and WEP networks are fine. I do not have a WPA network to test on, but my school's WPA2 Eduroam network does not work. It tries to connect before asking again for my credentials, and this repeats. I'm on 64-bit 10.10 Ubuntu upgraded from a live CD install of 10.04. Laptop model is Acer Aspire 5741-5193. Output of lspci:
I'm unable to connect to a particular home wireless network under Fedora 9, although I can connect to it using WinXP on the same machine. My Fedora installation is able to connect to my college's unsecured wireless network, so it's not a driver issue I think.It seems to be an authorisation issue, as I'll describe below, but there's one other thing that's bothering me. The SSID for the network I have problems with is for some reason not listed in Network Manager's drop-down list, nor is it in the output of iwlist wlan0 scan. But I'm pretty sure it's not a "hidden" network - I don't know exactly how those work, but I helped the owner of the wifi network in setting it up, and don't remember doing anything that would make it hidden. As far as I can remember, Windows found the network automatically without having to be told the SSID. What's the best way to confirm whether it's a hidden network or not?
Anyway, I try to connect by selecting connect to other wireless network in Network Manager, and entering the SSID. As far as I can tell from the error messages below, the machine does contact the network and attempt to connect, but I'm not authorising myself properly. That may be a completely wrong diagnosis, but hopefully someone can see from the below info whether it's correct or not.I'm not sure which option to use for "Wireless Security": at the time we set up the network, it gave us a Hex WEP key of 26 characters, which is 104 bits. But none of the options in Network Manager's list match that. Here are the options it has, and the error message I get with each one:None - if I select this, it fails to connect, with no error message. WEP 128-bit passphrase - if I select this and attempt to use my 26-character WEP key, it brings up a new dialog, saying "Passwords or encryption keys are required to access the wireless network [SSID]." It has a drop-down box labelled "Wireless Security", but this time the only option is "None", and the connect button is disabled, I can only click cancel. WEP 40/128-bit hex - as above. WEP 40/128-bit ASCII - The connect button is disabled when I try to use the WEP key, as the string is too long. Despite the fact that it says 40/128-bit, it actually accepts 5 and 13-character strings (40 or 104-bit). Since I've got a 104-bit hex key, I tried converting it to ASCII, but it consists of mostly unprintable characters, so I'm not sure there's any way to actually enter it into the textfield. I might have done something wrong here, so I've put my code below to see if anyone can point out a mistake. LEAP - requires a username, not applicable here I think. Windows doesn't need one, and we don't have one from when we set the network up.Dynamic WEP (802.1x) - requires username, private key and various other things, all N/A WPA & WPA2 Personal - Brings up a dialog with the same text as for "128-bit passphrase", but this time "WPA & WPA2 Personal" is the only option in the drop-down list, instead of "None". It asks for a password, so I just enter the hex key again - now it asks for the password for the Gnome Default Keyring, which I don't think I've ever set up. Don't know if I can go any further with that, but my understanding is that since we were given a WEP key when we set up the network, WPA will be N/A.WPA & WPA2 Enterprise - as Dynamic WEP. N/A.Hopefully that's enough info that someone can help diagnose the problem. Some of the behaviour of Network Manager described above doesn't make sense to me, and I'm wondering if it's buggy.
After installing Lucid, I noticed that my Ralink RT2860 card would not connect to my home network using WPA2 despite the network being visible and of good strength. So I followed the guide at [url] in order to install the newest Ralink drivers.
After installation, same issue. That is, the card will connect to my a/b/g/n network if I leave it unprotected, but it will not connect to the same network if switch it to WPA2. After being given the passphrase, the wireless icon on the indicator applet shows that it is trying to connect, but after awhile it fails. Does anyone know why the built-in driver and also the official Ralink driver are no good for WPA2 in Ubuntu 10.4 for my RT2860 card?
I updated to the latest version of Ubuntu and before I could connect to the network "krafft" that is a WPA2-Personal protected network.If I go into Windows and change security to none I can connect with Ubuntu, but not when it's protected.After a bit of time logged in without network a dialogue pops up and looks almost like this :but "Focus" is replaced with "krafft" and the password is something else.I know that the password is right and the network worked perfectly before update.I got an USB wireless network receiver from D-Link and the chipste is ralink rt2870.In the previous Ubuntu distribution you had to write "blacklist rt2800usb" in /etc/modprobe.d/blacklist.conf but it won't work with or without that blacklist.When I updated I saw some message about the network manager(at least I think so) so maybe the problem is in that.
I have xbmc, a media center shell that runs on ubuntu. I am trying to set up a laptop to run it and be a full time media center. so far it works great, I installed xbmc live, but the only issue is I have a wep2 protected wireless router and the wifi does not connect automatically.
I have it set up and am using wpa_supplicant once those commands are run the wifi works great.I am a novice in linux in general, and can not seem to get this to work on startup, can anyone point me in the right direction on this? I haven't been able to find the xbmc start up script if one exists, I figured adding those lines to it might work,does this sound like a reasonable approach? if anyone knows where that is and how it is defined to be launched on start-up i would appreciate it(I guess this is getting into the general Linux knowledge but still good info)
Well I recentelly read some tutorials about "cracking" wep networks, and seems like it's kind of easy ( I Haven't tried'em out since I don't have my laptop right now, but i'll try them as soon as i get it back )So i'd like to change my network protocol to wpa2, but I REALLY GOT NO IDEA on how to do this.Does someone knows about a tutorial on how to do this?
Its seems Fedora 11 on eee pc 1000h cannot connect to any wireless type(Open, WPA2, WPA or WEP) of a hidden network(non broadcasting SSID). Though it can connect to visible ones(broadcasting SSID), since my college is on a hidden network this a problem for me. Though I can't really test if its just fedora 11 or rpmfusion drivers for it 1000h model related problem.
In my toshiba m900 with realtek wireless lan. i canot detect any network. should i see any network? i setup my access point using wpa2 in windows. how about the ubuntu 10.04? i mean do they support wpa2 and wireless issues?
I see the network applet in the panel which shows that I am connected but I cannot access the net. I found out that I had to do this in firefox
about:config --> IPv6 --> disable.IPv6 true
With this tweak I was able to connect to the net. But when I use the Update Manager or Synaptic I am not getting connected, even if I use the cli and do
I recently installed and now my wireless Internet isn't working.have a Dell Inspiron 1545 laptop, with the 1397 wlan mini cardI have read through other threads, but I was unable to solve the problem I am having (Stated below).I just installed ALL updates available and plugged in my computer to connect to the Internet.Now the wireless option is there, and so is my network, but when I select it, nothing happens
I have a network of 5 Windows Machines and 1 Linux Server. I created a Filemaker Pro Database on a windows machine and share it with the other machines through web publishing (only locally). - On any Internet browser, they only have to go the IP of the computer hosting the database - http://192.168.1.99:120 to enter & use the database, and all the other windows machines connect perfectly.
However, when I type the same IP(+port No.) into Firefox on my Linux computer, it can't reach the windows computer with the database (It just times out). Is there a firewall preventing it from connecting to other computers on the network, or do I need to update firefox or run another Internet browser or install Samba? I don't have much experience with Linux, as a programmer set the server up for me, so a simple solution with as little programming as possible would be fantastic.
I've recently installed Lucid Lynx 10.04 on my Dell Studio which uses an internal BCM4315 wi-fi card to connect to the internet. I was hoping it would work upon the install, but deep down I knew I'd have to tweak it a little bit to get it up and running the way I wanted. The card was instantly recognized but, at first, wasn't detecting wireless networks. This was quickly and painlessly fixed using System > Administration > Hardware Drivers, which I used to install Broadcom B43 wireless driver (b43-fwcutter). I rebooted and could not detect the local wireless networks.
I entered my password to my home network (correctly, I quadruple checked) but, unfortunately, it continuously tries to connect to the network with no successful. Occasionally I'm prompted to re-entered the password and the process repeats. The network I'm trying to connect to is a WPA/WPA2 network which I've heard to be troublesome. I haven't yet tried connecting to a WEP network but I'm fairly certain it will work and I will get back to this post when I test it in a few hours.
I'm curious if this question has been answered or if the problem has been solved and I just simply don't have the google skills to find it.
In setting up wireless connections I have ran into an array of problems. First, when I installed the new OS on my laptop I had to get the correct drivers and firmware for it to display and connect to any connections, had no problem here connecting to a secure wireless network (WPA or WPA2). I then installed Ubuntu on my desktop and had to find the correct driver for the Netgear WNDA3100v2 USB adapter, got it all installed with the Windows Wireless Drivers tool or w/e it is. This made all the available connections come up. I tried connecting with the WPA password I was given for the network and will not connect.
I had the guy managing the network change the one I connect to, to a WEP Passphrase Shared Key thinking this would solve my issue, still nothing. And also in doing so, now my laptop will not connect to the wireless network using the Passphrase. I do not want to go back to Windows, and I will be getting rid of my Lan connection soon so i need a solution to fix this wireless connection problem.
Just purchased a Dell Inspiron 580 MT tower pc with Windows Professional. However unable to connect to the network or the internet when I load a copy of Ubuntu Karmic on dual boot. Windows networking and internet working fine. Is this an ethernet adaptor hardware issue? Broadcom NetXtreme 10/100/1000 Gigabit Ethernet controller-PCI Express card Will try later connecting through a usb ethernet adaptor to see if this is really the problem.
I am using Belkin router and i connect with MAC ID only. When i connect with my Vista it works properly but when i reboot and try to connect with Ubuntu it's not connecting.
I looked for my Ubuntu mac id and i added that also but no use. It says it's connected and when i try to google it, the page not found
This is baffling me but I am easily baffled/baffeld? I carefully followed these instructions to install a a working driver http://ubuntuforums.org/showthread.php?t=760568. It all went fine, my wireless light came on and it detected my wireless network. I know my WPA2 code (I can connect on the same computer in windows 7) and my keyring code. but I still can't connect it whirs away for quite a while before giving up and saying not connected.[Code]....
The graphical option through the hardware drivers list 2 options, broadcom b43 wireless driver and the broadcom sta wireless driver None can be activated
The b43 displays: Sorry, installation of this driver failed.
Please have a look at the log file for details: /var/log/jockey.log
