Fedora Networking :: No Network / Internet With 11?
Jun 15, 2009
I've worked with Fedora 10 for quite a time, with no problems regarding network or internet.Now that I've upgraded to Fedora 11, nothing regarding networking works. I have a dual LAN nVidia controlled network card. I've tried every possible network setting (dhcp, local only, etc...) and also tried to connect 2 pc's via direct connection, all without a result.
When I activate dhcp (as I normally would do/did), fedora tries to connect (with this blue balls spinning next to the clock), but then after a while, I just says that the network doesn't connect (the little red cross over the network connection).If I try to enter the ip, gateway, etc... manually, it says that I'm connected, but I can't ping0find any other computer or router.
View 2 Replies
ADVERTISEMENT
Oct 16, 2009
2 days ago I did a fresh install of Fedora on my computer to be dual-booted with Linux Mint. The first time I did this install a few weeks ago, I did all of the updates, rebooted (internet still fine) and when I rebooted again, Fedora could no longer connect to the internet (but could still see the networks and ostensibly connect to them). I fixed it then by manually setting the BSSID/IP/DNS/etc.
And this happened again on the new install! This time it took out the internet connection in Mint too. I tried manually setting the connection settings, but that didn't even work for a while. So, last night, thinking that the install might be the problem, I reinstalled Fedora. This morning I finally got my internet to connect on Mint, but I'm concerned that if I do all of the updates on Fedora I'm just going to end up back at square one with zero internet connection.
View 3 Replies
View Related
Sep 20, 2010
I'm using VPNC to connect to a remote cisco network, however I cannot browse the internet after the tunnel establishes. I know this is a DNS issue, as I can ping external address by IP (e.g. google). I can also communicate through the VPN tunnel without trouble.
/etc/resolv.conf gets updated by the VPNC with the remote networks DNS Servers, but I still cannot connect to the internet. I even manually tried to add my local nameserver to the /etc/resolv.conf file, without luck.
Also, just as a side note, I can only establish the tunnel via the command line "vpnc" command. I'm using Fedora 13 with KDE, but knetworkmanager / networkmanager will not establish the tunnel, however I haven't really dug very deep as to why. I've just setup some vpnc config files for loading the various connections manually, as needed.
View 1 Replies
View Related
Sep 25, 2010
I just installed Fedora 13 64bit Gnome, but I can't connect to the internet for some odd reason.
If you look at the image below:
I have marked the network icon, but on my desktop I don't have that icon for some reason...
Since I'm new @ Linux(Picking it up again) I went to the services and checked 2 services:
The network manager service was running but the status said: This service is dead.
And the network service was also running but status was: The status of this service is unknown.
I also went to the Administration menu and checked Network, the first tab showed no devices, but when I went to the hardware tab it did show my card.
I also don't believe that this is hardware problem since the card worked just fine under Fedora 9 or 10(Don't remember).
So if anyone got some solutions for me it would be great...
Some related hardware info:
lsusb
Code:
Code:
View 2 Replies
View Related
Jan 31, 2011
How to make my fedora 8 be able to connect to the internet by using wireless network ?
View 5 Replies
View Related
May 14, 2011
I am new with IP tables stuff and i have a problem....i have a pc Contain a fedora OS and i want to make a small network (4 PCs Contain XP OS) and using the pc of fedora OS as a firewall i want to Prevent the ping (i think it called(ICMP)) in the privat network and prevent one of the PCs from Browsing internet(prevent port 80 and 81 as i think) and i still don't know how to make the internet go Through the firewall to the private network...
Note: WAN = eth0
LAN = eth1
View 1 Replies
View Related
Sep 7, 2011
I just installed a dualboot win7/F15 on my laptop (dell XPS 15) and everything seems to be working fine except that when I connect to my network it is connected and the network is accessible (I can visit my gateway/ router) but when I try to visit a website it simply never ends loading it.Internet is working on win7 so it isn't my network's fault.Now I found somewhere that updating could help but since I dont have internet I can't update
View 3 Replies
View Related
Mar 1, 2009
I have a fedora 10 box with two network card on eth0 I have a pppoe connection to the internet, on second card eth1 I share my internet connection end I set up a samba server but I don't know if the settings are good. How to do this settings right to work fine, the ip are assigned by dhcp I don't use any static ip .When I try to browse the internet from the other computers some site's like {.com ; .org ; .info} are block, other site from {.ro} are working. Someone tell me something about turn off all my filters, but I don't know where to find this filter to turn it off. And when I use samba I can't have and internet access or vice versa. My network look like that:
Code:
eth0
|<--pppoe connection
|
MyComputer
(fedora 10)
|
eth1
|
switch
|
comp.1 comp.2
Win OS MacOS
View 2 Replies
View Related
Jul 13, 2009
I upgraded from Fedora 10 to Fedora 11 last night in response to a pop up window. When I rebooted after the upgrade my wife immediately complained about the internet not working. Actually the connection up was working but Fedora 11 upgrade had made it slow almost to a stop There are two XP machines the network behind a local D-Link wireless router with Comcast high speed internet. When I disable networking on the Fedora machine the internet connection immediately returns to normal on the other two machines. Also there is a second or two period after enabling networking for a quick upload or download before the connection clogs.I checked the system monitor network history and found that there is a constant networking send rate of just under 180 kb/s in the background.This occurs even when the browser, email client, and automatic backup are off and the only process showing significant CPU use in the system monitor is the monitor itself.
I tried netstat but there were so many /tmp/orbit entries that I could not scroll up to the top of the listing. Is this normal. If so, does anyone know the netstat command options to just see connections with sent packets. I also tried ifconfig -a. This shows no Rx packets at all, and no TX packets except on eth0, The total etho TX packets matches t,he reported by the system monitor, and in the monitor you can watch the total accumulate in approx 180 kb/sec increments. I don't understand why 180kb/sec TX would make a dramatic difference in internet network internet speed. Comcast reports upload speeds in megabytes. I need to be able to use the net in Federa, but I am also curious to learn what is the caused the problem.
View 2 Replies
View Related
Dec 30, 2009
I have a wired lan at home with 2 XP boxes connecting to a router to a DSL modem. I want to network my laptop, running only fedora os, for file sharing, printing and internet access. I will be using the laptop probably exclusively for creating/maintaining a Drupal-based (LAMP) e-commerce site to replace our old one for our small family business.
View 4 Replies
View Related
Aug 1, 2010
I have just started using fedora 13 and I am not sure if i am in the right area but here goes...today I was online in my fedora 13 partition on my laptop and I had been online for quite a while then I shut down my machine to recharge the battery then a couple hours later I turned it back on and all of a sudden my network manager applet was missing and I could not connect to the internet, I opened firefox and tried to get to my homepage but it basically just told me that I wasnt connected..
I suspected at first for some strange reason that MAYBE it was my NIC so I booted up into my vista partition and low and behold the internet works fine, so the problem is on the linux side, I have tried every command nm-applet but it just keeps saying an instance of nm-applet is already running, I have no clue how to restore the network manager and get my internet back and the only other piece of information I have is that earlier today I did do a bunch of security updates but the internet was working fine all day even after several reboots through out the day.
View 1 Replies
View Related
May 28, 2011
I just installed F15 on a laptop that previous had F12 working well. During install, it finds my wireless card and seems to set it up fine. The full install ran with the wireless active without any problem that I could see. Now, when I start up, I see Network Manager tells me that the wlan is active, but it doesn't show my specific network. If I click on the NM tray icon and open up the panel, my network is shown but it is not "active".
I can double click on it and it will become active - shows the little globe next to the antenna. This works fine for about 2 web pages worth and then FireFox 4 stops being able to find web pages. If I go back to the panel, double click on my wireless network (which looks like it is active already), and reactivate it, I can get the page I was looking for in FireFox, but within a couple of minutes it will stop.
Likewise with yum, while I'm installing software, I'll occasionally get errors like this:
[URL]: [Errno 14] curl#6 - "Couldn't resolve host"
If I reactivate my wireless network in the NM panel, it continues fine. Other computers/phones connected to this network seem to work fine. Is NM known to be problematic in F15?
View 14 Replies
View Related
Aug 6, 2010
I know Windows forward and backward but I am so new to linux it's just wrong. I just installed fedora (like 1hr ago) on and old toshiba laptop with a WiFi PC card. Everything seems to work fine except. My Networks connects to my home Wifi network but it will not connect to internet. When it connects the IP address isn't even close to being in the same range as my other laptops and PCs. Like I said I'm new to linux but I'm wanting to learn. Any fixes for this issue? Which linus book is the best one to read for a beginner? Other then not connecting to internet I have no complaints.
View 14 Replies
View Related
Jun 22, 2011
I recently installed fedora 15 on my computer but I have a huge problem. I can connect to my router wirelessly for a couple of minutes only. Afterwards my computer has no Internet connection although the network manager and the icon on the upper bar says that i am still connected. I tried editing the /etc/rc.local and /etc/resolv.conf as mentioned in other posts in here bit no luck so far.
View 6 Replies
View Related
Mar 31, 2009
I have two networks. One of them is wired, the other is wireless. The wired has an internet connection and a few other computers connected to it. The wireless network has a few hosts connected to it too, but it has no internet connection. What I've been trying, fruitlessly, to do, is make all connections that are bound to the internet, or my wired network, be routed that way, and all the connections to the hosts of the wireless network go that way.
Here's the setup..
Wired:
192.168.1.0/24 Gateway = 192.168.1.1
Route internet through here
Wireless
192.168.2.0/24 Gateway = 192.168.2.1
If my computer sends a packet to the internet, it should be routed through 192.168.1.1 If I send a packet to one of the local hosts of the wireless network, it should be routed through 192.168.2.1. Here's the routing table I've set up(This is one of many configurations I've tried)
Code:
$ ip route show
192.168.2.1 dev wlan0 scope link
192.168.2.0/24 via 192.168.2.1 dev wlan0 src 192.168.2.4
[code]....
With this, and everything else, I get destination host unreachable when pinging. The strange thing is that, if I unplug my eth cable, reboot and connect to the wireless network, everything is fine and I can access the router and the others. I'm trying to improve my networking skills, as I've had this of setting up a small linux box as a router for quite some time, for the fun of it, but I need to get routing under control before I go ruin my network.
View 6 Replies
View Related
Apr 29, 2011
I'm running Fedora 14 and when I'm surfing the web, it seems to lag in between pages. I don't think its my net connection, I just wiped windows 7 off my system for Fedora and it did not suffer from the same lag issues.I've tried adding in google's alternate dns server 8.8.8.8 but it didn't seem to fix the issue. I ran into this issue a couple years back on Ubuntu 8.1 or something like that, and I never could find out what I needed to configure.My second problem is that when I try to connect to other Windows systems on my wlan or wired connection, it gives the error "failed to retrieve share list from server". I'm not experienced in networking, can someone explain this to me?
View 1 Replies
View Related
Mar 17, 2010
I'm trying to setup network server for a week now and I was able to setup network in which i can ping the other workstation that is connected to my switch which is also connected to my server and I can also ping the server from local workstation.
I have 2 NIC, I use eth0 to dial to my dsl connection(ppp0 has the IP of my internet) and I use eth1 to connect to the switch and use to connect to the other local workstation
Now my problem is I don't know how can I share the internet connection from my eth0 or the ppp0 to my eth1 to the network, what do I need to be able to share the internet connection to the workstation that is connected to my switch.
View 3 Replies
View Related
Jan 18, 2010
I installed Ubuntu 9.10 using the default setup (Gnome I think) and on my Gateway Notebook using a wireless connection. It appears to be working great and I can even see my Windows drives and network storage on my home office systems.I have also set it up to run my favorite Bible software on Windows running under VirtualBox. I then installed the KDE Desktop so that I can select either desktop when logging on.
However, once I am in the KDE desktop, I cannot connect to the internet. I have checked and double-checked and the wireless settings seem to be the same on both the Gnom and KDE Desktops but still no network or internet connection when using KDE. I might mention that I am using the 64 Bit version of Ubuntu.
View 2 Replies
View Related
Feb 24, 2011
On the 25th of January, one of my computers randomly stopped being able to connect to the Internet. It was running a dual boot (Ubuntu 10.04.1 LTS & Windows XP SP2), and is connected to the network via an ethernet cable (no wireless). According to the Network Manager, everything is working okay (there was no change from when I was able to access the Internet).
When I would use Firefox, I would get the message "Waiting for (page)...". However, this is not a Firefox only problem, as every program requiring Internet access (e.g. Evolution) is unable to connect to the Internet.
I compared the Internet settings to those of my father's Windows XP SP1 computer, which is able to connect to the Internet. There was no difference, except for the IP Address and Hardware Address. Because of this, I incorrectly deduced that either the actual Ethernet cable or the wall plug was faulty. I tried using a different cable and connecting to the Ethernet wall plug used by the aforementioned computer. Nothing changed. I was still unable to connect.
I didn't worry about it until Tuesday, when my other computer had exactly the same problem. It is running a triple boot between Ubuntu 10.04.1 LTS, Ubuntu 9.04 and Windows XP SP2, and I am unable to obtain Internet access using any partition. As with the previous case, my computer showed no change in the Internet settings, and the computer also shows it as being connected to the network. It is also connected via an Ethernet cable.
View 1 Replies
View Related
Feb 27, 2011
Me and my friend have been talking about networking our two machines over the internet. So he has done his side. Now i need to do my side... Any ideas on how i would go about configuring my computer to do this?
View 9 Replies
View Related
Mar 13, 2011
I have a Toshiba Satellite L505D-GS6000, and I installed Ubuntu before and it worked flawlessly until I decided that I had to go back to Win7 because of certain program compatibility issues.I'm back here trying to set it up and am having no issues except for with my wireless. I can see all of the SSID's, I am able to connect to my wireless, and it displays that I have been assigned an IP and all of the other settings given by DHCP.
I have been trying to fix this for hours, googled, searched these forums, and have spent time with some people on the Ubuntu IRC channel and we are unable to come up with a fix.
Print out of sudo lshw -C network:
Quote:
*-network
description: Wireless interface
product: RTL8191SEvB Wireless LAN Controller
vendor: Realtek Semiconductor Co., Ltd.
[code]....
The strange thing is that although nothing will load when I try to visit facebook.com, google.com, or any other website... I opened the update manager and I noticed that it would download for 30ish seconds, stop and do nothing for 60ish seconds, resume for another 30, stop, resume, etc. until it finished. I am able to ping my router, and 8.8.8.8, but I am unable to ping [URL].
View 9 Replies
View Related
Jun 13, 2011
I want to connect to a wireless open ad-hoc network to have internet access. It worked a while ago (1/2 year or something) but some update must have messed something up so it doesn't work any longer. Situation: There is a laptop that is running windows 7 and is connected to the internet via cabel. A open ad-hoc network is configuered with sharing of internet connection, status of the ad-hoc network is "waiting for users to connect". I want to connect with a second laptop that is running ubuntu 11.04. I can find the network and connect to it.
Problem: I cannot get any internet access while being connected to the ad-hoc network. So my questions are: how can i find out if what causes the Problem? I suspect a driver issue, but I'm not sure. required information from Howto post a wireless issue:
[Code]...
View 5 Replies
View Related
Sep 1, 2011
I cannot connect to the Internet by LAN. The light of the Internet card is off. On Windows, the system says the cable not plugged while I have plugged it. I solved this by change speed and duplex mode. However, on Ubuntu, the changing doesn't work
View 1 Replies
View Related
May 3, 2010
I Have Ubuntu 9.10 Server installed and for some reason after updating our server with the ubuntu update manager, we can no longer connect to the network via remote desktop, let alone not even able to ping. We are actually able to connect to the internet itself just fine so I dont understand why this isn't working
View 3 Replies
View Related
Mar 22, 2011
I have created more A record in dns. one record is link to my local ip, i have already static ip, how can i access my local website from global.
View 11 Replies
View Related
Dec 6, 2009
MY OS IS (Widnows XP ) I'm Using VMware Workstation 7 to run My BT4-Beta (backtrack 4)
in my OS Windows XP I have Internet I'm in big network our administrator using Cyberoam Client for Corporate to allow people using Internet.. so if any people connect this network they should has id in Cyberoam if they don't has id will can't connect to the internet.. they will redirect automatically to the log in page in Cyberoam.
So ! in VMware Workstation 7 i configure network adapter to Bridged and i see internet icon with green color but dose not browse internet and also i can't ping my computer this is mean network dose not appear to backtrack my computer is in the network when i try to do ping this is what happened.
And this output to try run network!
PHP Code:
And this is my ifconfig
How to do Step by Step to connect the network using VMware WorkStation!
View 3 Replies
View Related
Jan 10, 2010
The installation of Ubuntu 9.10 on my HP NC640 worked fine and the network adaptor was successfully recognised: I see the message 'Wired Network Connection 'Auto Eth0' active' and when I open Active Network Connections I see the IP addresses that have been assigned.
However, if I open Firefox, I cannot connect to the internet. I tried pinging some addresses (www.yahoo.com) and that seemed fine. I then tried to run a first system update and Ubuntu seemed to be able to retrieve some packages but not others.
I then tried opening 'Network Connections' and adjusted the MTU (to 1100) and changing the settings of IPv6 (various settings: eg. 'ignore') but none of that seemed to help. Here I wanted to switch off IPv6 but it looks like none of the settings did this. Is there maybe another place where I should be looking? Do I have to do this with the command line? (I hope not) Or can I switch off IPv6 in the system settings? And should MTU be automatic? Or should I set something there?
View 2 Replies
View Related
Feb 5, 2010
I am attempting to connect Ubuntu 9.10 to the Internet.I have a network connection, and Karmic detects it fine. I can ping addresses within our network (e.g. the Windows computer in the next room), and I can ping the router, but if I ping, say www.google.com, it says "Destination Net Unreachable". Previously, in Jaunty, I had a similar problem.I found a workaround: launch Pidgin. Somehow, launching Pidgin temporarily edits my configuration. However, in Karmic, I have no access to Pidgin, however, and Empathy does not do the same thing. Since I have no Internet, I cannot "sudo apt-get install" anything.How can I get the Internet working?
View 5 Replies
View Related
Feb 18, 2010
Just purchased a Dell Inspiron 580 MT tower pc with Windows Professional. However unable to connect to the network or the internet when I load a copy of Ubuntu Karmic on dual boot. Windows networking and internet working fine. Is this an ethernet adaptor hardware issue? Broadcom NetXtreme 10/100/1000 Gigabit Ethernet controller-PCI Express card Will try later connecting through a usb ethernet adaptor to see if this is really the problem.
View 2 Replies
View Related
Mar 12, 2010
I just installed Ubuntu 9.10 64 bit on my HP Touchsmart TX2 1020us which has a Broadcom 4322 chip. At first my computer didn't seem to see the card at all, but then I typed the command (sudo apt-get install bcmwl-kernel-source) and then restarted the computer and now I'm connected to the network, but cannot connect to the internet so how do I figure this out. Like I said I have very little experience with linux at all so please don't make your answers too complicated.
View 5 Replies
View Related
