I cannot connect to the Internet by LAN. The light of the Internet card is off. On Windows, the system says the cable not plugged while I have plugged it. I solved this by change speed and duplex mode. However, on Ubuntu, the changing doesn't work
View 1 RepliesI can connect to the internet through wifi, but I cannot connect to anything on my network. I have a printer and a NAS, so I would really like for this to work again. I have a dell laptop with a Broadcom card.
View 9 Replies View RelatedThe installation of Ubuntu 9.10 on my HP NC640 worked fine and the network adaptor was successfully recognised: I see the message 'Wired Network Connection 'Auto Eth0' active' and when I open Active Network Connections I see the IP addresses that have been assigned.
However, if I open Firefox, I cannot connect to the internet. I tried pinging some addresses (www.yahoo.com) and that seemed fine. I then tried to run a first system update and Ubuntu seemed to be able to retrieve some packages but not others.
I then tried opening 'Network Connections' and adjusted the MTU (to 1100) and changing the settings of IPv6 (various settings: eg. 'ignore') but none of that seemed to help. Here I wanted to switch off IPv6 but it looks like none of the settings did this. Is there maybe another place where I should be looking? Do I have to do this with the command line? (I hope not) Or can I switch off IPv6 in the system settings? And should MTU be automatic? Or should I set something there?
Just purchased a Dell Inspiron 580 MT tower pc with Windows Professional. However unable to connect to the network or the internet when I load a copy of Ubuntu Karmic on dual boot. Windows networking and internet working fine. Is this an ethernet adaptor hardware issue? Broadcom NetXtreme 10/100/1000 Gigabit Ethernet controller-PCI Express card Will try later connecting through a usb ethernet adaptor to see if this is really the problem.
View 2 Replies View RelatedI just installed Ubuntu 9.10 64 bit on my HP Touchsmart TX2 1020us which has a Broadcom 4322 chip. At first my computer didn't seem to see the card at all, but then I typed the command (sudo apt-get install bcmwl-kernel-source) and then restarted the computer and now I'm connected to the network, but cannot connect to the internet so how do I figure this out. Like I said I have very little experience with linux at all so please don't make your answers too complicated.
View 5 Replies View Related2 days ago I did a fresh install of Fedora on my computer to be dual-booted with Linux Mint. The first time I did this install a few weeks ago, I did all of the updates, rebooted (internet still fine) and when I rebooted again, Fedora could no longer connect to the internet (but could still see the networks and ostensibly connect to them). I fixed it then by manually setting the BSSID/IP/DNS/etc.
And this happened again on the new install! This time it took out the internet connection in Mint too. I tried manually setting the connection settings, but that didn't even work for a while. So, last night, thinking that the install might be the problem, I reinstalled Fedora. This morning I finally got my internet to connect on Mint, but I'm concerned that if I do all of the updates on Fedora I'm just going to end up back at square one with zero internet connection.
I Have Ubuntu 9.10 Server installed and for some reason after updating our server with the ubuntu update manager, we can no longer connect to the network via remote desktop, let alone not even able to ping. We are actually able to connect to the internet itself just fine so I dont understand why this isn't working
View 3 Replies View RelatedI have had a heck of a time trying to get my laptop running ubuntu to connect to my home network. I have managed to get it to work at my university which would seemingly be more difficult than getting it to work at home, so I know for a fact it isn't a hardware or driver issue. If I try to connect via ethernet cable from my router, it detects that I connected the cable but says "disconnected" and never lets me connect. If I SKIP the router and go from my modem directly to my laptop via ethernet cable it works great.
Using the wireless network tool I can see all of the wireless connections in my area. When I go to connect to my network it prompts me for the WEP key and when I enter it and hit connect it just keeps cycling and eventually times out and finally again prompts me for my WEP key. I know this network works as it works just fine on my Windows 7 partition. Another interesting note - both my wireless and ethernet connections both worked flawlessly and stoopid easily on the live cd but don't after the full install.
If I manually enter in the information for my wireless through IPv4 settings and enter in the Address,Netmask and gateway I can connect to my network - but then I have no active internet connection. Same deal with my wired connection. Is this because choosing this manual method grays out the DHCP?
I just installed Fedora 13 64bit Gnome, but I can't connect to the internet for some odd reason.
If you look at the image below:
I have marked the network icon, but on my desktop I don't have that icon for some reason...
Since I'm new @ Linux(Picking it up again) I went to the services and checked 2 services:
The network manager service was running but the status said: This service is dead.
And the network service was also running but status was: The status of this service is unknown.
I also went to the Administration menu and checked Network, the first tab showed no devices, but when I went to the hardware tab it did show my card.
I also don't believe that this is hardware problem since the card worked just fine under Fedora 9 or 10(Don't remember).
So if anyone got some solutions for me it would be great...
Some related hardware info:
lsusb
Code:
Code:
How to make my fedora 8 be able to connect to the internet by using wireless network ?
View 5 Replies View RelatedI have installed WvDial (apparently) but it has no icon or launcher to start it by default, how do i get it to run? I also need basic set up how to. I am running Ubuntu 9.10 (Karmic) and network manager doesn't seem to be able to use my modem to connect to the internet (set up wizard works, appears connected, but then I get page not found error). Hence I wish to use WvDial to try to connect instead.
View 9 Replies View Relatedi have 3 comps(running ubuntu 10.04) and a laptop(running vista sp2). i have installed samba on all ubuntu comps. i have a printer attached to one of the comps and it has been shared also the internet connection on that comp has been shared. all the computers are connected using lan cables through an ethernet switch. i also have a wireless router which is connected to the ethernet switch.
I am able to view all the comps on the network except the laptop running vista. all the desktops are visible on the network and are able to print and share files on the network and also connect to the internet.the laptop running vista can connect to the internet but its not visible on the network and nor can it share files across the network or access the printer.all the systems have a static ip.
I have just started using fedora 13 and I am not sure if i am in the right area but here goes...today I was online in my fedora 13 partition on my laptop and I had been online for quite a while then I shut down my machine to recharge the battery then a couple hours later I turned it back on and all of a sudden my network manager applet was missing and I could not connect to the internet, I opened firefox and tried to get to my homepage but it basically just told me that I wasnt connected..
I suspected at first for some strange reason that MAYBE it was my NIC so I booted up into my vista partition and low and behold the internet works fine, so the problem is on the linux side, I have tried every command nm-applet but it just keeps saying an instance of nm-applet is already running, I have no clue how to restore the network manager and get my internet back and the only other piece of information I have is that earlier today I did do a bunch of security updates but the internet was working fine all day even after several reboots through out the day.
I have one pc on which I have installed slackware and samba (fixed IP, mask 255.255.255.0) I have another PC (also XP) which also has fixed IP running XP, and I can connect that to the slackware server easily My third PC connects to the internet and gets its IP address from the Cisco router(?) that provides the IP and mask on boot up.
I tried changing the IP and Mask on the slackware server to match the internet PC (which uses a mask 255.255.254.0) but the PC mask and IP changed on the internet PC I want the PC that connects to the internet to also be able to connect to the slackware server, but I see no need for the slackware server to also connect to the internet - I will mainly use it as a file server When I worked for another company I think the IT department talked about having 2 network cards in the PC that connects to the internet
I know Windows forward and backward but I am so new to linux it's just wrong. I just installed fedora (like 1hr ago) on and old toshiba laptop with a WiFi PC card. Everything seems to work fine except. My Networks connects to my home Wifi network but it will not connect to internet. When it connects the IP address isn't even close to being in the same range as my other laptops and PCs. Like I said I'm new to linux but I'm wanting to learn. Any fixes for this issue? Which linus book is the best one to read for a beginner? Other then not connecting to internet I have no complaints.
View 14 Replies View RelatedI'm using ubuntu karmic and I'm not able to connect to the internet with my reliance netconnect data card using network manager. Other distros like fedora, opensuse n sabayon connected easily with nm. Ubuntu detects the data card flawlessly but just doesnt connect.This problem has been persistent even in previous ubuntu versions, n I used to use wvdial. But downloading wvdial on some other comp with every dependency is really cumbersome.
View 6 Replies View RelatedI installed Suse 11.2 on clean HD. I cannot connect to the internet. Seems like Suse didn't install drivers for on board ethernet card. It is a Marvell Yukon 88E8056. I'm new to this and don't know how to install the drivers.
View 3 Replies View Relatedhow to connect my network data card to run internet on openSuse..
View 4 Replies View Relatedthe thing is that I cant use Network Manager to connect to Internet, because it simply do not connect. The connection, although, awailable throught yast when i choose "traditional method with ifup", so everything is just fine, but if i need to reconnect, i have to reboot. How do I setup a !working! connection through Network Manager, or maybe i do not do something properly.
View 5 Replies View RelatedOn this box I have Two seperate Ubuntu installations. Recently in both I seem to be having the same problem. I initially can connect to the internet as per normal and use any internet application. But after a period of time, sometimes just minutes, sometimes hours, even though the icon says connected, I cant update pages or send emails etc because there is no actual connection. My Physical connection is good I know - My Ubuntu laptop and Windows gamming PC connect fine during this period. So
Does this suggest an intermittent hardware fault or is there some thing in Ubuntu I can check to make sure that it is setup correctly and nothing has been corrupted? I am a lay PC person - I dont really want to be command prompting - Plug & Play and Point & Click is my limit.
I tried to install Xubuntu 10.10 Maverick as dual boot on my laptop. However when xubuntu is on, I can't find a way to connect to internet. When I try the 2 arrows on the up-right corner the option for wireless is deemed. I tried offline/online, that did not work either. when I click the firefox It says you are not connected.
View 1 Replies View RelatedI am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
[Code]....
I had put my computer on standby and when i restarted it, it powered off within a few seconds. I turned it back on and after that i've lost connectivity to internet on Ubuntu 10.04.
However I have VMware (XP) installed and internet/network works on that. I'm a newbie with Linux.
Here are some outputs:
I have tried to edit the connection using System>Preferences>Network Connections. I entered manual settings for IPV4, but whatever i enter there, it doesnt get reflected when i type ifconfig in the terminal window. I tried setting it to Automatic DHCP as well. Doesnt work.
I am trying Open Suse 11.2 KDE Live CD and don't know how to connect to the Internet. What do I do?
View 9 Replies View RelatedWhen using Fedora in VMWare, sometimes I can connect to the internet and sometimes I cannot. I do nothing differently on different days. I restart the machine and / or shut the machine down at the end of the day. When the machine starts back up the next time, I might have an internet connection or I might not have an internet connection. The 2 computer symbol that appears in the top will also sometimes be displayed. If I have that icon and click on it, it will display connections I can use including a sys one. I have a bridged connection chosen in VMWare also. Furthermore, when I click on the System -> Administration -> Network Device Control, 'eth0' is listed and it is listed as 'active'.
Yesterday I could ping out to a specific ip address on our network ( 192.168.1.xxx ). Now, I cannot ping that same ip address. I receive an error 'Destination host unreachable'.
How can I make it so that I have the internet connection every time I start up the machine? What do I need to check as far as the internet connection goes and the network connection?
I have a fresh install of ubuntu. I am trying to load some new packages but I think I need internet connection. The issue is I cannot connect to the internet I think I need to setup a network package so I can connect to the internet? This is the first time I have used linux.
View 3 Replies View RelatedSo I've recently installed Kubuntu 10.04, and after the first and second runs, the system refuses to connect to the network/internet. I'm not sure why this is, or how to fix it. It shows up in ifconfig, but other than that I'm at a loss. The Knetworkmanager applet says "Disabled" when I hover over it, and no connection can be made to the internet (apt, Firefox). I'm running x86, with a Biostar T5XE mainboard (Realtek RTL8168D/8111D network chipset). The logs don't seem to indicate a problem, though I could be wrong. The connection is known good: it connected before, but it won't now.
View 1 Replies View RelatedRemoved Network Manager (Wicd) - Now Can't Connect To Internet
View 1 Replies View RelatedI installed 11.2 on an older HP Laptop which was running XP without any issues. Durring the install, the update processe failed (presumably unble to connect to respository). I am usind a wired connection and the nic is connecting to my router and is recieving an address via DHCP. I am also able to ping the workstion from the router's Web interface. However I am unbale to connect to the internet.I have turned off the Suse firewall via Yast and checked the settings against another computer running ver 11.1 .Everything appears to be correct but no joy.
View 9 Replies View RelatedSo here is what I am trying to do. I want to connect my Open Suse 11 machine to the internet. I am almost there.
1. I configured my network card and eth0 is up.
2. I configured my DSL with user name and password and I am authenticated.
3. An IP address is assigned to me and the DNS servers are retrieved.
However I cannot ping or visit any website I use the YAST automatic configuration and kinternet to connect. Here are the gritty details
[Code]...
I do see that kinternet has trouble reading /etc/resolv.conf. It says 'permission denied' although read permissions are set on both /sbin/route and the path that it links to. This should not matter however since the existing entries are already there and valid. I also tried to turn off the firewall suspecting it could be a problem.
So I am being authenticated successfully ( verified with the logs ); assigned an IP; the route seems ok; firewall seems ok. But I cannot browse or do internet things I have been tweaking settings for 3 days now and all seems in vain. Do enlighten me on what I am doing wrong. I bet its something silly that I overlooked. I have had success configuring the same thing in red hat linux and browsing the internet without trouble. Is there something OpenSuse specific that I am missing ?