Fedora Installation :: Installer Cannot Detect My Target Disk ?
Jul 12, 2010
I have a dual CPU Xeon machine that I have been using various versions of fedora on for years.
The machine has the following disk layout:
I currently have Fedora 10 and grub installed on hda and I had to jump through hoops to install such as disabling the promise controller and reassigning drives because that blasted /dev/mapper kept grabbing the Maxtor ATA drives although I didn't want it to.
Anyway, in the BIOS I can boot from the secondary IDE controller so I want to install Fedora 13 on hdb. Problem is, the Fedora installer won't detect the drive.
Its partition table is as follows:
There is approximately 69GB of free space on this disk but the blasted python based installer wont show the disk as a possible installation location. If I exit to a bash shell I see that the device nodes do exist and I can manually mount and manipulate the disk but the installer is brain dead where the disk is concerned.
I will mention that sdc, sdi, and sdj are used with mdadm to create high performance striped volumes. Also, sdc shows up under /dev/mapper and I don't want to use /dev/mapper at all. I want simple /dev/sd? mount points...no stinking /dev/mapper, and no stinkin volume manager wrappers...
Why I cannot get the installer to use /dev/sdb?
Is there a disk signature on /dev/hd[bc] that is causing them to be grabbed by /dev/mapper, and if so, how would I remove that signature from the drive? /dev/mapper is vacant under Fedora 10.
View 2 Replies
ADVERTISEMENT
Oct 12, 2010
I have a ssd cosair harddisk with both usb and sata connecters. If I connect it with sata anything is working fine, and I managed to install Fedora core 13.
But I also want to be able to use the harddisk when it is connected with usb and that causes problems.
When I boot the Fedora Core 13 dvd It can't detect my usb harddisk.
When booting in install mode it just don't detect the harddisk.
When booting the dvd in rescue mode it don't detect the harddisk, and it don't create any entries in /dev/ for the harddisk. It is like there is no disk at all.
I have tested this on 3 different computers, so it is not a problem with my specific motherboard. So either it is a problem between my harddisk and Fedora Core 13, or there is some problems with the usb drivers in the boot image used by the Fedora core 13 dvd.
The disk is working fine if I connect it via usb to an existing Windows install, so the usb connection is working.
I installed Fedora core 13 with the harddisk connected to sata and then re-connected the harddisk to usb. It then boot up, but complain about missing root filesystem. Most likely caused by missing usb driver in my kernel.
But anyway, what I really want is the ability to boot from both sata and usb, so I can take the harddisk with me and boot it on other computers with usb.
So is there a command which allows me to build an kernel image which can boot from usb or am I trying to do something which is not really supported?
I did update my fstab to use LABEL=myroot
There is 1 Windows partition(NTFS) and 1 linux partition on the disk. (No seperate /boot partition and no swap)
View 1 Replies
View Related
Jul 8, 2009
I have an Asus P5K motherboard with an Intel Core 2 Duo 8400. It has 2 SATA hard disks, a 250 GB Seagate and a 500GB Hitachi.
I've been running Fedora 10 x86_64 for 6 months on this computer without problems.
I'm trying to do a new Fedora 11 install on this computer but the installer (Anaconda?) only detects the Hitachi disk.
I've tried to make a new Fedora 10 install to check if it was a media or disk problem and it detects the two hard disks.
I've tried to install it via a Live CD, and the installer only detects the Hitachi disk. The LiveCD detects the two hard disks, I can access it, partition, format, write, but the installer only detects the Hitachi.
I've tried to change from Enhanced SATA (AHCI) to Compatible in BIOS without success and I've changed SATA cables from one disk to the other, changed the disk order and nothing.
Must I enter some boot parameters for Fedora 11? Has the LiveCD installer some options?
View 2 Replies
View Related
Oct 5, 2010
I have a Dell Poweredge 2970 2x3.0 GHz AMD 64bit dual core, Perc 5/i controller, and 2 brand new Fujitso SAS 15K 146GB drives.
Trying to install Ubuntu 10.04 Server 64 bit from USB. At the point of detecting disks, the installer only recognizes the USB. The installation was created using Pendriveinstaller ver1.8.0.1 per Ubuntu Server web site instructions. I have the drives configured as 2 separate raid 0 arrays using the bios raid configurator. The drives have been initialized. (Tried before with a single Raid 1 array, but had same issue and since have read Ubuntu support for hardware raid is not great, so was going to bypass hardware raid for now).
I've seen some chatter on here about opening a terminal at this point and removing dmraid but don't see an option for terminal only shell.
View 1 Replies
View Related
Apr 20, 2011
Having trouble installing 'Squeeze' 6.0.1a-amd64-netinst on a new AMD64 system.The installer boots and runs fine until it gets to hard disk detection. Then it hangs for about 20 minutes showing a blue screen, during which time the HDD-activity light flickers every 5 seconds. Eventually it says it can't detect a hard disk, and displays a (longish) list of possible drivers; no idea which, if any, would suit.Anyone else installed (successfully or otherwise) on this combo?
View 3 Replies
View Related
Oct 13, 2010
I've just installed Fedora (F13) for the first time, on a new HDD, to give myself a dual-boot system. So currently I have:
So, at the appropriate stage in the install menu, there is an option for where to install GRUB, and a drop-down to choose which drive is the primary BIOS boot drive.
However, in both cases, no other drive except my new sdc is visible. So, I can install GRUB to MBR of sdc, or to first sector of boot partition - but no option to put it to my primary boot drive MBR on sda.
Likewise, in the GRUB configuration page, if I go to Add another OS, the only option it gives me is my new Fedora install. It doesn't list the Vista OS on sda at all.
The result is that I can boot to either OS by changing the boot drive priority in BIOS.
I guess my question is this:
- is this expected behaviour from the installer, meaning that I'll need to configure GRUB manually somehow? (gulp ) or
- did I do something wrong in the install process? or
- is this some weird bug manifesting itself?
View 12 Replies
View Related
Dec 28, 2010
I have Mint 9 installed on a 120GB, WD SATA HDD. Now I want to install Ubuntu 10.10 on this HDD. Downloaded i386 desktop image and created a bootable USB stick with the image. System boots fine but installer do not detect My HDD. It only lists my USB drive. Even Gparted donot detect the drive. Typing sudo fdisk -l also lists only my USB Drive.
View 3 Replies
View Related
Mar 21, 2011
Ubuntu installer does not detect my sata drive during installation.
Hardware:
Asus p4gv-mx
4gb ram
250gb wd sataII drive
ide cdrom
Bios options tried:
Disabling apci 2.0
disabling apci
setting IDE mode to
[Enhanced]
[compatibility] w/both sata only, pata& sata settings
Setting my pata cdrom to slave and plugging it into the slave position of the ide ribbon.
I've tried these combinations with the usb installer, and dvd installer.
I've tried loading the live cd/dvd & usb then running the installer with in.
I've tried the spacebar method, hitting f6 and apci=no, noapci
The live cd has no problems detecting and mounting my hdd, however the installer does not detect it.
View 3 Replies
View Related
Aug 11, 2011
I'm trying to install Ubuntu 11.04 alongside Windows 7, but when I boot from the CD, Ubuntu refuses to detect the presence of Windows 7. I tried unplugging all my external hard drives to see if that made a difference, but Ubuntu still can't tell that I have Windows 7 on there.
View 4 Replies
View Related
Apr 17, 2011
I downloaded this "debian-6.0.1a-amd64-netinst" iso image....But on the partitioning screen, after selecting the manual partitioning, it shows the whole hard disk without detecting the XP partitions.
View 2 Replies
View Related
Feb 21, 2010
I'm using the Ubuntu 9.10 alternate install CD in an external PATA USB CD drive to try to install Ubuntu on a ThinkPad X60. The installer boots but then very quickly gets to a stage where it complains that, "No Common CD-ROM drive was detected". It asks you to point out the drive or load or select drivers, but there aren't any drives or drivers to choose. I brought up another console, and looked in /dev, but there isn't anything there that resembles a CD drive.
I tried
$ modprobe ide-scsi
But it can't find the module.
I followed the instructions here, found the drivers on a working system, and put them on a thumbdrive. However, when I mount it:
$ mkdir /tmp/drive
$ mount /dev/sdc1 /tmp/drive
Mount fails due to an "invalid argument," with two different USB drives that work just fine on other systems. When even mount doesn't work, I feel like I've got both hands tied behind my back. How I can correctly implement the above command-line fixes? I'm not sure what I'm doing wrong. I've installed different Ubuntus probably a dozen times over the years, and haven't gotten stuck this badly since somewhere around version 4. Whether this problem is specifically related to the fact that my external USB CD drive has a PATA interface. If I go out and buy or borrow a SATA USB CD drive, is this problem likely to go away?
View 6 Replies
View Related
Jun 26, 2015
“toshiba satellite u840w with hard disk drive and a solid state disk cache”
Debian 8 installer does not detect the hard drive during installation
I've recently tried to installed Debian 8. The problem is that the partition menu gives me these 3 options:
1. Configure iSCSI volumes
2. Undo changes to partitions
3. Finish partitioning and write changes to disk
There are no options for defining partitions or any hard drive during installation. After searching the internet i found that the problem because the solid state disk SSD cache. How I install a Debian 8 with computer which has a hard disk drive and a solid state disk cache.
more info: I want windows 7(64) and debian dual boot
View 14 Replies
View Related
Dec 19, 2010
I am trying to install Debian Lenny (64 bit) on my brand new Toshiba laptop (intel i3, 3 GB RAM) and for some reason the installer cannot detect the ethernet card. This is the error message I get:"No Ethernet card was detected. If you know the name of the driver needed by your Ethernet card, you can select it from the list."And then there's a list which is quite long -- and I cannot replicate it here. But I want to know why the installer cannot find the ethernet card on its own or find the appropriate driver. In any case how can I fix this problem?
View 14 Replies
View Related
Feb 16, 2011
I have a Windows XP system, and wanted to install Ubuntu to a 100 GB XT3 partition on the same drive. I was told I could chainload Ubuntu from the NT Loader menu. I booted from a Ubuntu 10.04 CD and ran the installer. It didn't find any hard drives. On a hunch, I tried the 10.04 alternate installer CD. That DID find the hard drive and partitions. I had the installer make /dev/sda7 (the XT3 partition) the root. Installation proceeded smoothly, but then the installer told me it did not see any other OS's on my drive! Why? I directed the installer to place grub on /dev/sda7 instead of the MBR.
Per the instructions I was given, I used DD to copy the first 512 bytes of /dev/sda7 to the Windows primary partition (sda1) as bootloader.lnx. But the resulting file is empty, and it won't boot. I repeated the whole process - formatting, installing FOUR times, and same results. I have no idea where GRUB was installed. It is apparently not in the MBR, because I still have my normal Windows boot. I downloaded the 10.10 alternate installer and got the same exact results. Even switched from XT3 to XT4. After two weeks of this nonsense, I still have yet to see Linux boot.
View 9 Replies
View Related
Dec 1, 2014
I'm trying to install Debian Jessie beta2 on a UEFI laptop. The installation worked just fine before with setting in manual partitioning an EFI system partition and a root partition.But when I try to partition with root as an encrypted volume I get this error when I wanna write changes to disk:" the attempt to mount a file system with type vfat in scsi1 partition sda at /boot/efi failed"When I choose resume partitioning the installer then freezes at "detect file systems".
Because my harddrive needs specific alignment I've made beforehand in gdisk:EFI System Partition of 100mib at /dev/sda1/boot partition of 512mib at /dev/sda2/ (because I expect the installer to want a /boot too for an encrypted device)rest of harddrive reserved for root at /dev/sda3
View 3 Replies
View Related
Nov 28, 2010
Ubuntu in Windows 7 (64 bits) File system installed using Wubi I got Ubuntu 10.04 LTS intalled using Wubi. That means Ubuntu resides inside Windows file / folder system. It also means Ubuntu does not have its own partition. Here is what I found out:
1) It cannot detect wireless network unlike Win 7 on this same laptop. However, when I plug in ethernet cable, it was able to detect it. Is there a fix this problem?
2) I cannot see Windows folders. How do access windows folder from Ubuntu side and vice versa?
3) I forgot to set the disk space for Ubuntu during install and I think the default is 17 GB.Would this cause me problems? If so, what do I need to do? How do I expand the disk space for Ubuntu?
View 1 Replies
View Related
Nov 17, 2010
I installed 10.04 or 10.10 on my laptop, which also has a 200 GB USB drive attached. Now, I am trying to go back and use the installer to repartition the disk. I noted that the scan of the external drive took about an hour, because I was on a webinar while it was happening. It would be nice if Installer noticed and asked if I really intended to sit by for an hour while an external drive was scanned.
When I went into the partitioner, there was another scan of several minutes, and then when I downsized a partition on the internal drive from 76G to 46G, there was yet another lengthy scan on the external drive. So, I know about this, and it's user error that I forgot to disconnect the drive, but it would still be nice if Ubuntu with some clue about what's most likely my intention, i.e. to NOT install on an external drive.
View 1 Replies
View Related
Feb 24, 2011
I have trouble installing ubuntu on my desktop machine. I had Mint before, reinstalled Win7 and wanted to upgrade to newest release as I didn't use Linux for some time.
Basically fdisk can see the disk but installer don't
View 5 Replies
View Related
Feb 7, 2010
The Install program is failing to see the hard disk!
Now heres the really weird bit. The live cd can see the drive just fine.
I have created partitions using gparted and the disktool also sees the drive just fine but as soon as I go back to the installer it shows no hard disk!
It's a SATA drive which I suspect might be a part of the problem.
Is there a way I can install without the install program?
Is there a way to make the install program see the drive?
This is ubuntu 9.10 desktop.
View 2 Replies
View Related
Mar 30, 2010
I want to install ubuntu 9.10 DVD, I have the iso image, so i try to boot the installer from hard disk by adding this lines to my menu.lst.
Code:
title Install Ubuntu
kernel (hd0,0)/install-ubuntu/vmlinuz
[code]...
View 9 Replies
View Related
Jan 24, 2010
I try to install Ubuntu on my new HTPC. I start Ubuntu with the Live CD and it boots fine. Then I want to start installing Ubuntu on my hard disk.Unfortunately the installer does not see my hard disk which has 1 empty ext4 partition. However, it can be seen and managed in GParted.
View 5 Replies
View Related
Mar 25, 2011
Just bought a new computer that I will use as server:
Gigabyte 890GPA-UD3H motherboard
AMD Phenon II 1090T
16 Gb RAM
4 x Seagate 2Tb hard disks
I tried to install Ubuntu server 10.04 and 10.10, both 64 bit, having similar results. Also I have tried enabling and disabling the RAID card. On 10.04 installer hangs preparing disk partitioning phase at 43%, on 10.10 hangs at the same stage 45%. Must I download something and apply before that phase?
View 1 Replies
View Related
Apr 11, 2011
Wanting to dual boot XP with UBUNTU. Live CD verified good.
ran df in terminal:
Ran sudo fdisk -lu in terminal:
Partition table entries are not in disk order
Originally I had two partitions for Windows xp of 100 gig each. I cleared / backed up the second partition and created two 50 gig partitions, splitting the second into two linux (using Gparted) partitions labelled root and swap.
Disk Utility sees this hdd as a RAID component. It is connected through a RAID controller.
The installer (in allocate drive space step) doesn't see them for some reason.
Hardware:
AMD Athlon 64+clawhammer processor
Asus A8N-SLI mobo
hdd as above
2 Gig RAM
DVD / CD Burner
View 5 Replies
View Related
Aug 26, 2010
I tried using the Windows installer, after not having success burning the ISO to cd, and I received another error message. "There is no disk in the drive. Please insert a disk into drive. DeviceHarddisk3DR3"
View 9 Replies
View Related
Apr 26, 2011
I have a problem with getting my Linux distribution (Debian amd64-bit) to install. Everything works the way it should - from booting a live CD/DVD (any distro) to running the text-based or gui installation right after bootup. Up until the Linux installation gets to the step for detecting my SATA hard disk drive(s), but before (or at the same time as) initiating the partitioning step, it'll freeze/hang my screen and my CD/DVD drives instantaneously - and the only fix is a forced shutdown and/or hard reboot.
I don't know what causes this, but I tried googling online and all that I really found out was that it might be an issue with running 32-bit vs 64-bit installations - but this is not the case; from running Gparted on Knoppix 32-bit or the partitioning step during a Debian 64-bit installation. Also, I read a random post online related to running kernel commands / parameters alongside the installation (e.g. acpi=off or something similar) stating that it might help?
Anyone got any ideas or solutions? I'm a real newbie when it comes to Linux (though, I'm quite knowledgeable when it comes to computers and technology, and Windows) - else I wouldn't be posting in this forum sub-section, hehe. I can't quite get my head around this one - despite trying my best to find a solution online beforehand.
View 2 Replies
View Related
Jan 17, 2010
"The installer encountered an eror copying files to the hard disk: [Errno 30] Read-only file system
This is often due to a faulty CD/DVD disk or drive, or a faulty hard disk. ..."
Before I try changing CD drives, re-formatting the hard drive (again), or cleaning the CD drive, I must add that Xubuntu did open. I got rid of all traces of the previous operating system (WinME), and Xubuntu seems to work pretty well. The installation stopped at 41% of copying files. Should I aim for a finished installation or is this fine?
View 9 Replies
View Related
Dec 2, 2010
Each time, different methods, I get this about 3/4 of the way through:
The installer encountered an error copying files to the hard disk:
[Errno 5] Input/output error
This is often due to a faulty CD/DVD disk or drive, or a faulty hard disk. It may help to clean the CD/DVD, to burn the CD/DVD at a lower speed, to clean the CD/DVD drive lens (cleaning kits are often available from electronics suppliers), to check whether the hard disk is old and in need of replacement, or to move the system to a cooler environment.
The only possibility of those is the CD being bad. But I've used it before, recently, and it was fine. I will burn another one from my other computer and try, but it shouldn't be doing this.
Question: If I plan to only use Ubuntu on this computer (no dual boot) should I make the /,swap and /home partitions all Primary or some logical, or does it even matter?
View 6 Replies
View Related
Apr 21, 2010
I'm trying to install fedora with the live cd into my windows machine. When i get to the select drive nothing can be selected.
View 1 Replies
View Related
Jan 12, 2010
I try to mount one disk image to two points.
sudo mount -o loop,user,uid=dm /home/dm/mmm/test_drive1.img /home/dm/mmm/fs
sudo mount -o loop,user,uid=dm /home/dm/mmm/test_drive1.img /home/dm/mmm/fs2
Thats done
But when i create,copy or change anything on one mount point (../fs) its not updates on second mount point (../fs2).
Does anyone know way to 'share' one disk image (.img) to some mount points?
View 3 Replies
View Related
Dec 19, 2009
Trying to install SUSE on a perfectly working PC that was running Windows. Blew away all the partitions and formated the drives.When trying to install SUSE, Installer will not detect my two hard disks. Tried with version 10.x, 11.1 and 11.2, without success.My Mobo is a XFX GeForce 8209, and my SATA drives are both Seagates (1x120GB, 1x320GB). I've tried different SATA mode selection (i.e. SATA, AHCI, and RAID) without any success either.I've tried to look for SATA controller drivers for my Mobo, to try to load on Installer startup, but failed there too.
View 1 Replies
View Related
